-
Product
Pneumatic Zero Drop Tester
-
HIACC Engineering & Services Pvt. Ltd.
Designed as per ISTA packaging standard, the Pneumatic Zero Drop Test stand is used to assess the drop bearing capacity of the specimen during its transportation and handling process. The system is ideal for testing the specimen vulnerability around edges, surfaces and corners at different heights.
-
Product
Needle Microprobe
MT-23/5HT
-
Fast-response 23 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Electronic Loads/Sinks
-
An electronic load offers the possibility of testing the specimen under different loads. Various load changes are simulated, as they can occur in normal operation. For this purpose, the relevant load current is set in a defined range and electronically controlled. For the test, different operating states are either programmed or entered into the system via an interface (USB, RS-232, GPIB...). For easy handling and quick use, there are four operating modes.
-
Product
CTGcalc™ Software
-
CTGcalc™ is a Windows application that sets up microwave network analyzers, acquires measured S-parameter data, and analyzes the acquired data for CTG’s various measurement fixtures. CTGcalc™ allows the user to extract complex dielectric permittivity, magnetic permeability, or sheet impedance of the measured specimens.
-
Product
Acoustic Noise
-
American Environments Co., Inc.
A Test Specimens can be evaluated in two different modes in reference to acoustic noise: The Test Specimen's response to acoustic noise and the Test Specimen's generation of acoustic noise.
-
Product
Electrodynamic Vibration Test Systems
DC-series
-
Depending on the reference PSD or other operating conditions such as the specimen, one part of the controlled response may deviate from the reference PSD
-
Product
Leak Tester
LSD-01A
-
Jinan Leading Instruments Co., Ltd.
LSD-01A Leak Tester is applicablein leak testing of pouches, bottles, pipes, cans and boxes of foodstuff,pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It’ s also applicable in the leak testing ofthe specimens after falling tests and pressure resistance tests.
-
Product
Flexometer
EKT-2002GF
-
By means of applying constant load and compression frequency to the test specimen, this instrument could help the user to understand the history of Heat Built-up and dynamic fatigue poeperties of rubber compounds. For example, while tests the tire compound, it could provide the information of rolling resistance. Pt100 temperature sensor, temperature controller in PID parameters control, and air circulator are adopted to ensure the stable temperature control.
-
Product
Automated System for DMA+ Series
Xpander
-
METRAVIB Xpander is a unique cost-effective solution to address the increasing throughput requirement of testing laboratories. Xpander is an automated specimen handling system dedicated to the DMA+ series Dynamic Mechanical Analyzers.
-
Product
Non-Contacting Video Extensometer
AVE3
-
The AVE3 is Instron’s most advanced extensometer, engineered for high-precision, non-contact strain measurement across a wide range of mechanical tests—including tension, compression, and flexure. Its adaptable design accommodates various specimen types, sizes, and elongation ranges, making it ideal for everything from delicate films to robust metals. By eliminating the need for clip-on devices, the AVE3 streamlines setup and ensures uninterrupted data collection through specimen failure, even in high-energy break scenarios, such as composites. Compatible with environmental chambers and fluid baths, it supports non-ambient testing with ease. With compliance to ISO 9513 and ASTM E83 and a fast 500 Hz data rate, the AVE3 delivers reliable performance for demanding testing standards.
-
Product
Transportation Vibration Simulator
KD-9363
-
King Design Industrial Co., Ltd.
Transportation vibration simulator is mainly used to check the product encountered in various vibration environmental of manufacture, assemble and install, transit and usage process. Especially all types of transportation vehicle. Common transport is road, railway, sea, air, etc. To identify whether the product have the anti-vibration capability to endure transportation environment and avoid arrival damage and harm the company reputation. It also can analyze the specimen structure and study its dynamic character.
-
Product
Pneumatic Bidirectional Vertical Shock Test System
KRD17 series
-
KRD17 series pneumatic bidirectional vertical shock test system is the novel designed and developed for large specimens that cannot or are not easy to turn over, especially adopt for battery testing. It can complete vertical upward and downward shock test in one test stand without moving the UUT.
-
Product
SPI Flammability Tester (Vinyl Material)
TF318
-
TESTEX Testing Equipment Systems Ltd.
SPI Flammability Tester (Vinyl Material), to determine the ignition properties of vinyl plastic film material according to CFR 16 Part 1611 U.S.A. Flammable Fabrics Act for flammability of apparel vinyl plastic film.The rate of burning shall not exceed 1.2 in./s as judged by the average of five determinations lengthwise and five determinations transverse to the direction of processing, when specimen is placed at an angle of 45 degree and expose to the standardized flame (22# fire nozzle, 1/2 inch. In length).
-
Product
Insect Rearing Rooms
-
Standard walk-in incubators or coolers used in the rearing of drosophila and other biological organisms often end up being problematic for a number of reasons. The acids inherent in the rearing of many specimens or their food can quickly corrode a standard refrigeration evaporator. High humidity exacerbates the issue, as droplets of concentrated acid will collect on the cooling components.
-
Product
Single Space Electro-hydraulic Servo Universal Testing Machine
WAW-F Series
-
Jinan Testing Equipment IE Corporation
WAW-F series single space Servo-Hydraulic Testing System Computerized is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The ultra-large testing space & dual-action actuator with longer stroke enable it to test not only standard specimen, but also longer ones with long elongation every so often. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing System Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Tester of Single Space is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
-
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
Product
Mechanical Testing
-
The Mechanical Testing Department at IMR is well equipped to perform most standard mechanical testing, as well as specialized tests designed to the customer's requirements. A complete in-house machine shop supports the department with precise specimen preparation and fixture fabrication.
-
Product
Samples Preparation (Polisher/Grinder)
-
* LCD displays all the cutting data.* The diameters of specimens to be cut range from 5 to 8mm (1008:100mm) and the cutting capacity reaches 100x200mm.* Manual cutting and automatic cutting can be changed over at random. * Large cutting chamber & tempered-glass view window.* Non-burnt movable cutting mode which greatly improves cutting quality.● Automatic retract at the end of cutting operation.● Dual-direction feed which increase the depth of cutting.
-
Product
VCS
Broad-Band Random Vibration
-
The program Broad-band random vibration is intended for testing the specimen with the use of broad-band random vibration with a particular intensity degree.
-
Product
Hydraulic Servo Control Compression Testing Machine (Four Column)
TYE Series
-
Jinan Testing Equipment IE Corporation
This series Servo-Hydraulic Compression Testing Machine is mainly designed for compression test of building material items, such as concrete cubes, cement specimen, paver materials and related component, etc. With new design idea and advanced technolog, this series has more advantages in appearance, operation & applications. The compression testing machine is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching at scientific institutes.
-
Product
Digital Imaging
-
No one camera does it all. ACCU-SCOPE offers a wide selection of cameras for a variety of applications, and our experts can help you find the best match for your specific need. We have solutions from brilliant brightfield to low-light fluorescence, and from imaging living, moving specimens to fixed stained sections on slides. Need help deciding? Just ask!
-
Product
Type 1 And Type 2 Pantograph Grips
-
Pantograph grips use a simple spring design to hold and apply pressure to specimens during tensile testing. These grips are mainly used for tensile testing plate specimens of rubber, textiles, or soft plastics.
-
Product
Averaging Clip-on Extensometer
2650 Series
-
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
Product
Martindale Abrasion Tester
SG-P02M
-
This machine is ideal for determining the abrasion resistance of upper, lining, socking, and similar types of shoe materials, particularly those made of fabric. The specimens are capably tested for four bieces or six pieces(option) per time and are rubbed over the abrasive in all directions in a complex, repetitive pattern(a lissajous figure) and, at the same time, the holer totates.
-
Product
Fully Automatic Plastic Tensile/Bending Testing Machine
-
This is a fully automatic tensile and bending tester for plastics. It is capable of continuous operation from measurement of specimen dimensions, supply, and data processing.
-
Product
Needle Microprobe
MT-29/5HT
-
Fast-response 29 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Vibration Test Systems
G-9 Series
-
The G-9 Series Vibration Test Systems, featured by high eccentric moment and a large loading table supported by the unique rigid lateral suspension structure, are suited to transportation tests for relatively large specimens; packaged goods and electric apparatus. In addition, the unique structure enables horizontal tests of relatively heavy specimens without conventional horizontal slip tables.
-
Product
1 KN Eccentric Roller Grips
-
These eccentric roller grips are specifically designed for tensile testing flexible materials, such as rubber and soft and semi-hard plastics. Named after the non-symmetric roller design, these grips employ a simple and quick clamping mechanism. They also have a self-tightening action, which maintains clamping of the specimen during testing regardless of any thickness reduction. In addition, the upper and lower grip faces are parallel grooved to help hold these soft materials.
-
Product
IEC60068-2-75 Spring Impact Hammer
-
Shenzhen Chuangxin Instruments Co., Ltd.
Adjust the impact severity by rotating the knurled cap until the desired energy- value is displayed. Pull the knob slowly out of the device until it locks in place. If moved too fast, the clamp may skip its arrester and will lock at its way back when the pulling-force declines. Hold the device horizontally at it’s housing tube and press the (black) release cone to the specimens plane of impact. The strike is automatically released when the release force threshold is reached.
-
Product
Automatic Contacting Extensometry
AUTOX750
-
The Instron AutoX750 automatic contacting extensometer offers automated, high-precision strain measurement by motor-driven contact arms to engage specimens—eliminating manual setup while maintaining sub-micron accuracy over long travel. They integrate seamlessly with Instron testing frames and software to reduce operator error, speed cycle times, and ensure repeatable, standards-compliant strain data for metals, plastics, composites, and elastomers.
