Face
See Also: Human Body
-
product
Medical Face Masks Flammability Tester
Sataton Instruments Technology CO., Ltd
Medical face masks flammability tester is to determine the fire resistance performance of medical face masks and full face masks. The tester can provide a specific flame and make the dummy head with facepiece move to the flame under a specific speed. The operator can observe the effects of the flame on the masks and facepiece. The tester is suitable for medical face mask, respiratory protective equipment and full face masks.
-
product
End Face Inspection Microscopes
D SCOPE EFI – D SCOPE EFI-C – D SCOPE EFI-C LWD
The new D Scope EFI for MTP/MPO and multifibers field connectors is a cost effective microscope for inspecting fiber optic patchcords and cassettes.
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
product
Electric Servo Motor Type 4 Face 3 Axis Vibration Tester
The electric servomotor type 4-sided 3-axis vibration tester can control 4 vibration tables synchronously or independently by combining 4 independent 3-axis vibration testers.
-
product
Trainings, Seminars, Workshops
To make your staff able to face daily tasks and handle with high productivity is in the center of our trainings. Especially when a new test sytems starts to run it is extremely important that the personnel can operate appropriately from the beginning.Our workshops are designed as classroom trainings so everybody can concentrate completely on the workshop contents without being bothered by day-to-day business or other troubles.An alternative is the training in-house so we can look after individual and concrete problems directly on-site at the running test system.No matter if we teach in our rooms or in-house we emphasize to teach concrete practical content. The participants will spend at least 50% of their time with pracitcal questions or problems. Small groups ensure the individual care of each. We offer trainings in english or german language.
-
product
Electrical Testing Monitoring
The IEC 61850 represents the migration from the analog to the digital world to the substations. Accordingly, industry faces a period of transition, also noticing the effects of IEC 61850 in the traditional checking and monitoring procedures.
-
product
FlowSpec DDoS Mitigation
Large volumetric-based DDoS attacks are increasing in terms of frequency and scale at which they are perpetrated. With hundreds of-gigabits worth of attacks becoming commonplace, organizations not only face service interruptions for customers but the complete implosion of their infrastructure’s operation. In the face of this increasingly challenging threat landscape, BGP FlowSpec DDoS mitigation has emerged as one of the most effective techniques to mitigate DDoS attacks. Combined with an accurate and speedy detection system, it helps manage and synchronize working with firewalls to mitigate these attacks.
-
product
Fiber Test & Measurement
Thorlabs manufactures a range of devices for testing and measuring the performance of optical fiber. Power, spectral signature, polarization, or end face surface geometry can by characterized with out-of-the-box solutions from our catalog. EO modulators, optical switches, and light sources are available to treat light being used on a test bed.
-
product
End Face Inspection
Cleave quality inspection. High precision interferometers for checking the end face quality of cleaved optical fibers and for cleave process optimization. Crisp and clear fringe patterns and software with advanced measurement functionality. Ideal for use in production settings and when working with difficult to cleave fibers in laboratory environments. Fiber holder adaptors available for use with cleavers and splicers from the major splicer manufacturers. This facilitates easy transfer of the fiber from cleaver to interferometer and then onto the splicer with no need for reclamping.
-
product
IEC60065 Socket Torque Balance Tester Torsion Tester
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
product
Medical Equipment
We develop solutions for demanding medical applications. Whether a Home Healthcare CPAP or complex Robotic Surgical System, Haydon Kerk Pittman can deploy a solution designed to your program requirements. We offer lube free systems for clean, maintenance-free operation; specialty materials for radiation, autoclaving and chemical environments; smooth and quiet operation for patient facing applications; and miniature and micro product designs for precision fluid pump and drug delivery systems.
-
product
Digital Automated Fiber & Ferrule Interferometer For Single Fiber Connectors
DAFFI SF
The latest interferometer from Data-Pixel is a cost effective solution for high volumes production, without compromising on accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI SF to be robust, fast and accurate in order to meet all manufacturing or laboratory environments. With the Blink software platform, DAFFI is able to measure the end face geometry on single fiber connectors in a very short time. The Daffi interferometer accessories (flange and adapters) are fully compatible with the Daisi range, allowing the user to limit the costs of the 3D geometry measurement units.
-
product
1U Rack Adapter for Series HSF-1U, HSF-1UR
RA 19
The 1U high rack adapter will mount four of the low profile 50W, 100W and 150W (Series HSF-1UR or HSF-1U) power supplies. Each plug-in power supply is equipped with a power on/off, indicator LEDs and voltage test points. The RA 19-1U provides access to the DIP switches and rack keying without disassembling the rack. It also provides a redundant scheme with modules 1 and 3 being powered from one a-c input and modules 2 and 4 from a second a-c input. Module numbering is left to right facing the front panel.
-
product
Oscilloscope
RTA4000
Designed with top class signal integrity and responsive ultra-deep memory, the R&S®RTA4000 brings the power of 10 to a new level. The Rohde & Schwarz designed 10-bit ADC plus class-leading noise and memory depth provides sharp waveforms, more accurate measurements and confidence when facing unexpected measurement challenges.
-
product
Smart Manufacturing Solutions
The integration of the physical and virtual worlds and the speed of technological change are just two of the challenges facing manufacturers today. Industries undergoing a digital transformation, including IoT and the merging of IT and OT, are rapidly reshaping the manufacturing landscape. Don’t fall behind! Let our test expertise and extensive knowledge of ATEs confidently guide you through this new market reality.
-
product
Heavy Duty Dynamometers
MD-7500-HD
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 1-slot, Texas Instruments PCI1410 Chipset
P111
The P111 is perfect for use with Wireless LAN cards like WiFi / 802.11b or any of the newly emerging 802.11a or 802.11g standards. It also suits Bluetooth cards or other functions where the ability to occasionally remove the card is important, but where during normal use the rear facing aspect of the slot suits its operation.
-
product
Software Services
At Igence we like to talk with our clients, preferably face to face. We meet in the early stages of your project before we have started. This means we both get to know each other and we can begin to understand your needs as soon as possible.
-
product
Non-Contact Displacement Sensing System
KD-2306
Multi-purpose non-contact position/displacement sensing* Supports both dual and single coil sensors* Terminal I/O connections* Auto-synchronization of multiple channels* Analog DC and 4-20mA outputs* Single ended, bipolar, and differential voltage outputs* Front face coarse and fine calibration controls* RoHS compliant and CE marked
-
product
3D Machine Vision Process Control Solutions
In the age of automation and robotics, manufacturers utilizing automated dispensing in their assembly lines face growing challenges to maintain process control of their manufacturing processes. To eliminate errors and optimize product quality, they increasingly need the help of machine vision based “eyes of automation”. Whether manufacturing automobiles or medical devices, they need high-speed inspection tools to confirm the accuracy of their dispensing process and the overall quality of their products.
-
product
Optical Power Meter - PXI
Power 1400 Series
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
product
Temperature and Humidity Sensor, Cresnet
C2N-RTHS
The C2N-RTHS is a wall-mounted temperature and relative humidity sensor that communicates directly with any 2-Series control system via the Cresnet control network. One-piece mounting makes the C2N-RTHS simple to install. The 1-1/2 inch diameter face protrudes just 1/8 inch from the wall surface and is easily painted or wallpapered to blend into the wall surface.
-
product
Test Data Management
With increasing test data volumes, diverse data types, complex relationships, and data sensitivity, most enterprises face significant challenges with test data management. Having good quality data is key to testing enterprise functionality correctly and efficiently in the test environment. Copying production data to be used for the test can expose the company to numerous privacy and compliance risks. In the absence of a strong test data management strategy, you may end up jeopardizing your testing cycles and pile up huge infrastructure costs.
-
product
Protocol Converter
MACC2
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
product
OFFSOON Endface Cleaner
CA3006
CA3006 OFFSOON Endface Cleaner is a fiber endface cleaner for cleaning transceiver modules or components. By using pure liquid and gas, OffSOON shoots liquid to dissolve oil and dirt and blow the end face with air stream to remove the liquid and dirt and make the endface clean. The whole process just need 1 seconds. OFFSOON comes along with SC and LC type adaptors and fulfill almost every customer’s need for connectors cleaning jobs.
-
product
Fibre-optic Hydrophones
The best instrument available to measure close to the face of the ultrasound transducer, make CW measurements or to measure the acoustic pressure and associated thermal effects of a high-intensity field.
-
product
ITC Style VXI Module Shield Kits
* Box design for C-size ITC style PC Boards with 11 slots on their sides.* Pre-machined flat front panel with ejector handle cutouts.* Side shields include 0.375 inch wide vent slot on top and bottom sides for maximum cooling.* Shroudless design fits all VXI chassis.* Each kit includes side shields, front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.* Complimentary layout support includes PCB design template and CAD layout files.
-
product
Inspection Microscope
This compact, lightweight and ergonomic Inspection Microscope is specifically designed for inspecting ferrule and fibre end faces in the field or the laboratory. The microscope provides dual-illumination, both coaxial and oblique; to produce the highest-quality image detail and superior view of fibre end face cleanliness and core condition.
-
product
Remote Controller
ADLINK Bus expansion is a technology that increases the number of slots of the same or different bus type for a host computer system. ADLINK bus expansion product provides variety of interface options, including PCI, PCI Express, PXI, and ExpressCard to increase bus slots and leverage the latest computing power of both desktop and server-grade computers for a variety of applications. The interoperability of different bus interface devices, such PCI, PXI and PCI Express, is also a great benefit for those facing complicated system integration tasks. ADLINK bus expansion products also provide complete hardware and software transparency, without the need for additional drivers or software.
-
product
Flat Front Panel Kits
* Pre-machined, single-slot wide flat front panel.* Fits virtually any VXI B and C-size board.* Ejectors pivot on mounting brackets that mount on the PC board.* Each kit includes front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.
