-
product
Electronic Calibration Module (ECal), DC-4 GHz, 2-Port
N7550A
The N7550A is part of Keysight’s family of value-line electronic calibration (ECal) modules that makes calibration of vector network analyzers fast, easy and accurate. Cut your calibration down to half the time it normally takes using a traditional mechanical cal kit. Simply connect it to your instrument and the firmware does the rest. For greater precision and higher accuracy measurements consider the N44xx and N469x family of ECal products.
-
product
Carpet Dynamic Loading Tester
TF610
TESTEX Testing Equipment Systems Ltd.
Carpet Dynamic Loading Tester, by simulating walking to determine the effects to two of the main actions of walking: compression, and the shearing effect at the edge of the shoe.
-
product
Electronic Transformer Test System
UI2000-ET
• Input characteristics analysis 1) Measure Vrms (10-300V) Lrms (0.04-4A) W, PF, Hz, total harmonic and 0-50 component of harmonic 2) Accuracy: ± (0.4%reading + 0.1%range + 1digit) • Output characteristics analysis 1) Measure lamp voltage (1-60V) lamp current (03-20A) lamp power, crest factor and oscillatory frequency 2) Accuracy: Class 2 • It can print without compute, and provide the communication port for PC
-
product
48V / 250 Amp Load
EL15-48M
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
product
Electronic Instrumentation
Electronic Instrumentation is about the design, realisation and use of elec- tronic. systems for the measurement of electrical and non-electrical quantities. Strongly related fields are measurement science and data acquisition.
-
product
OEM, Embedded, and Custom Electronics
Picosecond timingPrecision analog and mixed signal processingDigital delay and pulse generationHigh speed photonics and fiberoptic timing distributionAerospace instrumentation and simulation
-
product
Electronic Ballast Automatic Test Equipment
ATE-1
Test series connection, parallel connection and series/parallel connections of the electronic ballast (about 15 kinds of connections), available for various electronic ballast. • With a precise resistance box, tube is substituted for the resistance, can act as many as 6 tubes. Resistance value: 1-4095Ω adjustable. • Measure input parameters (vrms, irms, w, pf, harmonics, etc), output parameters (on-circuit voltage, lamp voltage, filament voltage, lamp current, lamp power, oscillatory frequency), can also test the ballast efficiency, abnormity protection, and power symmetry of partial rectifier effect and etc. • Program controlled AC power source to guarantee the smart choice of input voltage and the frequency. • Equipped with 17 inch LCD controlled machine, specially designed A/D combined with special CPU, has the two left and right testing interfaces to achieve stability of data and high- speed testing. • We can make the special-designed product for you and promise to upgrade the software for free.
-
product
ELECTRONIC MEGOHMMETER
MI-2550e
The MI-2550e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 2,5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 5.000.000 MΩ with four test voltages: 0,5 kV - 1 kV - 1,5 kV - 2,5 kV.
-
product
Specialised Load Monitoring Products
DLM have a wide range of specialist monitoring equipment for industry specific applications, ranging from saddleback monitors for PLGR operations to logging subsea loads with our data loggers.
-
product
Electronic Speed Controller
AFI-ESC610
AFI-ESC610 is an Electronic Speed Controller designed to drive BLDC motors. It meets the industrial requirements of high voltage and high power motor application for electrical vehicles, airplanes, boats and medium duty industrial machinery. It is rated at 6KW.
-
product
Load Bank
RLB
RARA manufactures load banks, ranging from small portable units for testing generators to multi-megawatt designs for larger applications. Regular load testing, along with correct battery maintenance, is the best way of ensuring the reliability of standby power systems. It is routine for all newly-installed generating sets to have a load test during the commissioning process in order to prove the performance of the set and all ancillaries-cooling system, exhaust system, switchgear and protection schemes.
-
product
Digital PIN Electronics Module
P128C200M
The P128C200M module provides measurement and control of parameters of integrated circuits using parametric measurement methods, as well as functional and algorithmic control. The module implements a synchronization system that ensures the operability of a group of modules when they are installed in the AXIe-1 crate.
-
product
Electronic Pilot Balloon Theodolite
TEBAL 2
F. W. Breithaupt & Sohn GmbH & Co.KG
*Available in 12/2016*Observe, measure and transfer angles of elevation and azimuth of the flight of an ascending pilot balloon at predetermined time intervals to a tablet/laptop/PC*Determine wind speed and wind direction at certain air layers with an easy-to-use software*Ruggedized design*Easy to use*Quick measurement*Quality made in Germany*Reliable data and documentation
-
product
Surface Mount Reed Relays from Pickering Electronics
Pickering Electronics Surface Mount Reed Relays contain the highest quality instrumentation grade reed switches making them suitable for the most demanding applications and are suitable for infra-red or vapor phase reflow soldering.
-
product
Artificial Resistive Load
326
An industry staple for over 50 years, the TESCO Artificial Resistive Load (Catalog No. 326) has been redesigned to meet 21st century standards, making it the most cost effective, portable and light weight artificial load box on the market today.
-
product
Electronic Warfare MMI and HMI Simulators
MS 1600
The EW IFU (Electronic Warfare Interface Unit) interfaces between Cockpit electronics viz., RWR Display Unit (DU), New control Box (NCB), CMDS Control/Display units and Simulator Host Computer (HOST). The EW IFU transmits the status of the cockpit control units to the host, receives display data from the host and transfers the same to RWR DU, NCB and CMDS CCU/CDU. The display data for the RWR DU received from the host would comprise of the complete symbol data in respect of emitters that are to be displayed based on the data from the Instructor Station (IS) and control input from the cockpit. The display unit receives and presents the data as symbology on the display screen. The EW IFU based on the PC–AT.
-
product
Press Force Load Cell
6000 Series
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
product
Indicators - Electronic
An electronic device used to read an input value from a measuring device and show a displayed value.
-
product
Auger Electron Spectroscopy (AES)
Rocky Mountain Laboratories, Inc.
Auger Analysis, Auger Electron Spectroscopy (AES or Auger) is a chemical surface analysis method. AES measures the chemical composition of the outermost 100 Å of a sample. Measurements can be made at greater depths by ion sputter etching to remove surface layers.
-
product
Electronics Testing Solutions
Don’t cut corners when it comes to developing high-quality electronics functional testing solutions. Ball Systems helps you ensure you deliver the quality your customers expect by providing open and reliable advanced technical testing solutions.
-
product
Multi-interface Electronic Control Unit
The Mors Smitt CatEnergy control unit ECU is the most modular and scalable solution available on the market for all function using high voltage measurement. From Energy Measurement purpose to all essential train function, the CatEnergy ECU is the perfect compact system for all demanding application on existing and new build train.
-
product
S-Type Load Cells
S-Type Load Cells take their name from their shape – as you can see from the images below – they are in the shape of the letter “S”. These load cells are commonly used in tension applications; mechanical-to-electrical scale conversions as well as weighing applications including cranes etc.
-
product
24V / 400 Amp Load
EL12-24M
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
product
Resistive AC Load Bank
AC load bank testing offers you whole solutions of predictive failure analysis for UPS(uninterrupted power supply), generator, transformers, PV system, inverter etc, to validate the condition and output of such power systems comprehensively. Integrated AC & DC load bank could be made in one unit or separately with different load voltages as per your need for different applications.
-
product
Industrial Weighing - Wireless Load Cells
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
product
Website, Mobile & Web App Load Testing
LoadComplete
LoadComplete helps you design and run performance, stress, and load tests for mobile, websites, and web apps. It's very easy to use. In fact, it is so easy, that you can create your first load test within a few seconds, even without any programming knowledge. LoadComplete allows you to generate load through virtual machines, on-premise computers, or even the cloud. It's compatible with leading continuous integration environments, which allows you to find root causes immediately.
-
product
Beam and Singlepoint Load Cells
We have trimmed all the non-essential fat off these load cells, however you can be sure that nothing has been trimmed from the actual load cells, they are precision tested and certified to meet all the exacting requirements on the downloadable technical specifications shown below.
-
product
Load Logger
LL-230
AMETEK LoadLoggers* and LoadProfilers are non-invasive digital recording loggers for gathering data on distribution loads and power quality. Whether the data is from a load site or direct from the distribution system, the AMETEK Load Management products are easy to install, operate and analyze.
-
product
Resistive & Inductive AC Load Bank
RL
Resistive & reactive load banks are able mimic motor loads and electromagnetic devices within a power system as well as purely resistive loads by offering the ability to set a specific power factor (pf). Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit. JUNXY has an extensive range of resistive & reactive load banks to simulate these types of loads on a power source and the transformers, relays, and switches which will distribute the power throughout your facility.
