Tension
forces causing extension.
See Also: Force, Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Gravity, Electrical, Magnetic, Tensiometers, Tensile, Extensometers
-
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Computer Control Tensile Testing Machine
SG-L03B
These series of universal testing machine are used to test tension, compression, bend, shearing force, adhesion, peeling force, tear strength,...etc. of specimen, semi-product and finished product in the field of rubber, plastic, metal, nylon, fabric, paper, aviation, packing, architecture, petrochemistry, electric appliance, automobile,...etc. , which are the basic facilities for input quality contorl (I.Q.C), Quality Control (Q.C.), Physical Inspection, Mechanics Research and Material.
-
product
General Purpose Quartz Force Sensors
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
product
High Temperature Un-Cooled Extensometers (700 C)
Model 7642
Jinan Testing Equipment IE Corporation
These extensometers use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7642 is ideal for testing composites, metals and high temperature polymers in tensile, compression or cyclic testing. All units can be displaced in both compression and tension. The extensometer is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the extensometer. This system provides a number of functional enhancements, including high speed digital output, built in calibration and tare functions, analog and digital filters, and more.
-
product
Mini Low Profile Load Cell Universal/ Tension or Compression
MLP SERIES
The model MLP Series load cells were designed with economy as first priority. They are a scaled down version of our successful LPO Series Load Cells. MLP-10 through MLP-300 are anodized aluminum and the MLP-500 through MLP-1K are made from 17-4ph heat treated stainless steel. The unique low profile design of the MLP Series provides excellent stability for in line applications for tension and/or compression, while saving space at the same time.
-
product
15T Telemetry Running Line Monitor
RLM15T-3.0-T
The DLM 15T Telemetry Running Line Monitor measures the tension on a ropepassing through its three wheels. Typically used in cable laying and winch operationsto measure and record line tension. The robust and wireless design has become anindustry standard.
-
product
High Voltage Power Capacitors
Lifasa - International Capacitors, SA
Capacitors of correction power of cos φ and filtering of harmonics for AT of Lifasa, are manufactured under the base of the container / stainless steel box and porcelain terminals. There are two types, depending on the connection mode that we are going to use:*Single-phase (1 or 2 terminals) with internal fuses, for connection to the network through a double star. Recommended for networks of tension superior to 11 Kv or need of equipment of high power.*Three-phase (3 terminals) with internal fuses, for direct connection to three-phase network. Recommended for voltage networks lower than 11 Kv.
-
product
Tensile Tester
Wewon Environmental Chambers Co, Ltd.
Is a fundamental materials science test in which a sample is subjected to a controlled tension until failure
-
product
Optical Tensiometers
Theta Flex
Attension® Theta Flex is a contact angle meter that enables all measurements in one instrument for both research and quality control. It measures static and dynamic contact angle, 3D surface roughness, surface free energy, surface and interfacial tension, and interfacial rheology.
-
product
Wire Crimp Pull Sensor
Model MR06-200
The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the handles together to increase tension on the sample until a break occurs. The peak force is recorded by a Mark-10 indicator. A rotating turret with slots of multiple sizes accommodates a wide range of wire diameters, up to 0.25 in. (6.4 mm).
-
product
RFID Label Inspection System
Eurotech RFID FS
The Eurotech RFID FS RFID accurately rewinds rolls of RFID labels and validates their receptivity by running them through the Voyantic Tagsurance RFID inspection system. The unit allows stopping at a predetermined editing spot for the removal and replacement of the defective piece, as well as indicating defective labels by a mark printed by an inkjet system integrated with the machine. Adjustment of the closed loop tension control system can be made through adjusting the parameters on the software that control the servo motor control system. This gives the customer a virtual infinite range with which to wind their labels without cracking the inlay or antenna. As well accurate web adjustment and guidance is provided with a web guide system complete with an ultrasonic sensor. The Eurotech RFID FS RFID label inspection system is equipped with the Voyantic Tagsurance for testing the performance of RFID tags. This is done by verifying that the tag responds to commands on its whole operational frequency range, which means testing the tag on multiple frequencies, also outside the RFID reader frequency. Accurate power output combined with the Voyantic Snoop Pro antenna, optimized for testing tags inline at high speed, allows defining precise acceptance criteria and achieving stable quality.
-
product
Load Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
product
Force Sensor Elements
The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.
-
product
Motorized Force Test System
MT Series
In the past, film extruders, paper producers, converters, and woven/non-woven fabric producers have had the choice of test stands and universal test machines which are either value-priced peak-force-only machines, or expensive computer-operated integral-load cell machines. Now you can have the best of both worlds in a single instrument. The series MT-1500, a simple to use computer operated tester, with Quality Control software for automatic calculation and graphical display of break, elongation, yield, modulus, and other, tension and compression force information.
-
product
Automatic Tension Tester
HTYZL-H / 681
Wuhan Huatian Electric Power Automation Co., Ltd.
Measure the surface tension of various liquids (liquid-gas interface) and the interfacial tension of mineral oil and water (liquid-liquid interface).
-
product
Polarization Controller and Scrambler - PXIe
Pol 1000 Series
The Pol 1000 Series PXIe module enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands. Pol 1000 Series can be used with our wide range of optical and electrical PXIe test modules, and can be used to build complete mixed-signal test platforms.
-
product
Control Cables
TRIUMPH specializes in cable controls which are mechanical connections between controls and actuation systems used in a variety of applications. Our systems provide higher reliability, lighter weight, and greater control box selection. Current controls include wire rope, push-pull controls, sliding friction controls, ball-bearing controls and low-resistance and backlash mechanical control system cables. Wire Rope Controls: Wire Rope is used in applications where weight is critical, and the system operates in tension only. Assemblies are built to your required standards with unlimited configuration capabilities. Sliding Friction Controls: High load capacity in tension and compression. Flexible in any direction, wide temperature range and easy installation. No adjustment or lubrication needed during the life of the control. Ball Bearing Controls: Ball Bearing controls are a self-contained system that performs linear motion under tension or compression loads.Precise and accurate movement with high load capacity offering weight savings, low friction and high efficiency. Quick disconnect ends available.
-
product
Textile Tensile Testing Machine
TF001
TESTEX Testing Equipment Systems Ltd.
The Textile Tensile Testing Machine is designed to test a wide range of materials in tension, bursting, tear, elongation, constant load, elastic, thread slip, peeling and other mechanical properties.A PC-controlled machine equipped with AC servomotor and a quality ABBA ball-screw for ideal and smooth control. The machine talks directly with a PC running a data analysis software package in English or Chinese, via a high speed RS232.
-
product
Force Tensiometer
K20
Our Force Tensiometer – K20 is a robust, semi-automatic instrument for the precise measurement of surface tension and interfacial tension. Using the ring and plate method as the main tensiometric methods, it produces reliable measurements for the routine quality assurance of your surfactant solutions and interfacial processes.
-
product
Tensile Compression Force Tester
ESM303
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
product
Tension Load Cells
These Load monitoring systems are available in telemetry/wireless (RLP), self-indicating (LLP) and cabled non-indicating (WLP) versions. Towcell a 25kN, wireless tension load cell specifically engineered for the emergency services, salvage and 4 x 4 industries. Ruggedly built and highly accurate load link style load cell dynamometers allow for force and load monitoring across a broad range of industries and applications.
-
-
product
Superior Electromechanical Universal Testing Machine
WDW-S Series
Jinan Testing Equipment IE Corporation
WDW series computer control electromechanical universal testing system for tension,compression, flexure testing is designed according to ASTM, ISO, DIN, EN standards etc.. The electromechanical universal testing system for tension,compression, flexure testing is computer-controlled and precision. Our electromechanical universal testing system for tension,compression, flexure testing is widely suitable for metallic and nonmetallic materials for tension, compression, bending, shearing and low cycle test. The electromechanical universal testing machine features high precision, high stability and high reliability. Graph, test result display, data processing and printing can be done easily by its PC system and printer. Completed with modulus for metal, spring, textile, rubber, plastic and other material test, the electromechanical universal testing system for tension,compression, flexure testing is widely used in many fields such as industry factories, research and development, test institutes and training centers etc. WDW-S series superior materials testing systems adopt robust load frames, precise load weighting system, advanced measuring and control system, and intuitive modular application software. Configured with wide range of accessories for applications, the materials testing systems can provide the best testing solutions for your individual application needs. With 20 years’ experience of materials testing industry and based on abundant application knowledge, we are completely capable of configuring the best solutions and more accurate testing systems for the manufacturers involved in load frame, core measuring and control elements, software package, grip/fixture that based on their specified test application and other requirements.
-
product
Miniature S-Beam Load Cell
500 Series
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
product
Semiconductor Technology, Micro Scriber + Meters For Contact Angle And Surface Tension
SURFTENS WH 300
Optik Elektronik Gerätetechnik GmbH
The leading equipment for professional use in 200 and 300 mm wafer processing in semiconductor technology. SURFTENS WH 300 is equipped with a 3 axis wafer robot, wafer scanner, loadport for 200 and/or 300 mm wafers, fan filter unit, notching system. Suitable for any cleanroom class it features the automatic mapping of contact angles on wafers for up to 25 wafers.New: with SECS/GEM Interface!
-
product
Computer Controlled Electronic Relaxation Testing Machine
ERT-300
Jinan Testing Equipment IE Corporation
Model ERT-300 Computer Controlled Electronic Relaxation Testing Machine is designed for the relaxation tests ofPC steel bar, steel wires, indented wire, and galvanized steel wire etc. This machine adopts vertical load framewith great rigidity, AC servomotor with zero clearance & great torque precise reducer to drive the screw to carryout the adjustment of the test space, the tension of specimen and keeping of the load force, to complete therelaxation test. The machine is equipped with especially designed industrial PC. The control and data processingsystem of IPC has very high reliability, which can meet the requirements of data adopting, displaying, storage anddata analyzing demanded by the relaxation test that over 1000 hours; Testing standard: ASTM E328, ISO 15630, BS5896, ASTM A1061 etc.
-
product
load cell
EST-40
Technopark Automation & Control
The EST-40 is an 'S' type load cell suitable for use in tension and compression and is popular on hopper, tank weighing, belts scale and process weighing applications. It is low cost and is available in capacities from 50 kg to 2000 kg.
-
product
Axial Extensometer
Model 3542
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
product
Dynamometer
The PIAB Dynamometer is excellent for measurement and control of tension forces and weight, where accuracy, reliability and safety in all conditions is required. The PIAB Dynamometer conforms to the International Standards for Safety Inspectorates. The PIAB Dynamometer is an all-weather instrument, equally suitable for use in the laboratory as in the field for weighing and measuring mechanical tension forces.
-
product
High Altitude Wiring Clamp
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
