-
Product
Transport Expert
TX Series
-
The VeEX® TX product series offers a complete test solution for Next Generation of Transport, Metro and Carrier Ethernet Testing. Color graphical display assisted with touch panel enables users tapping through the test configuration and accessing complex overhead bits and bytes. Features include APS, TDM, pointer adjustment, pulse mask analysis, G.821/G.826/M.2100, histogram, and overhead access.
-
Product
30A, 50 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse
T3CP30-50
-
30A, 50 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse.
-
Product
40MHz
SM-4040
-
Waveforms*Main Waveforms: sine, square(only sine is available above 40MHz)*Waveform length: 8~16000point*Amplitude resolution: 12bit*sampling rate: 200MSa/S(≤80MHz) 300MSa/S(120MHz)*Built-in Arbitary: Triangle,±Ramp, ±pulse,rise/fall exponential,rise/fall logarithm,gause noise,cardiac,SIN(X)/X,DC*Waveform length: 8~160000point*Amplitude resolution: 10bit*sampling rate: 10MSa/S(≤80MHz) 20MSa/S(120MHz)
-
Product
High Gain Horn Antenna
BBHA 9120 K
-
The BBHA 9120 K is a linear polarized high gain horn antenna for immunity testing at short distances, especially optimized forAutomotive 600 V/m Pulse Radar Test 1.2 - 1.4 GHz. Standard: General Motors: GMW3097, Ford: EMC-CS-2009.
-
Product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
-
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
Product
Digital Delay / Pulse Generator
DG535
-
Stanford Research Systems, Inc.
The DG535 Digital Delay and Pulse Generator provides four precisely-timed logic transitions or two independent pulse outputs. The delay resolution on all channels is 5 ps, and the channel-to-channel jitter is less than 50 ps.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-3010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±8 kV*High pulse output current up to ±30 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
Activity Detection Unit
DG009-M1
-
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
Ultrasonic Testing
Pundit PL-200
-
The Pundit PL-200 is a best-in-class Ultrasonic pulse velocity (UPV) test instrument to examine the quality of concrete and other materials such as rock, wood and ceramics.
-
Product
P104 LVDT/RVDT Measurement Board
73LD4
-
NAI’s 73LD4 is a PC104-compliant LVDT/RVDT Measurement Board with six separate transformer-isolated channels. The channels can incorporate up to six programmable LVDT/RVDT-to-Digital Tracking Converters in a stack-through module. Each channel is programmable for 2-, 3-, or 4-wire inputs that automatically range between 2.0 volts and 28 volts, so there is no need to purchase multiple boards set for specific inputs. Operating frequency between 360 Hz and 10 kHz can be specified. Each channel also produces differential incremental encoder (A & B) outputs with programmable resolution and a zero-degree marker pulse.
-
Product
HBM Verification Tester
HBM-VT
-
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
Product
cDAQ-9185, 4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785064-01
Chassis
4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9185 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
Product
Modbus Transducers
THI Sensors
-
The THI-485 sensors are Modbus transducers for measuring thesurrounding temperature and relative humidity or for theacquisition of up to four passive pulse signals or digital states. This feature extends the possibilities of the device, turning it into a kind of RS485 pulse concentrator from other sensors andmeters.
-
Product
Autonomous RTU
BSC-50E
-
Infinite Industrial Informatics Lt
BSC-50E is an ultra low power, wireless RTU with data logging and alarming capabilities. The battery powered RTU incorporates a quad band GSM/GPRS modem, four digital inputs, three analog inputs, two pulse counters and multiple excitation options for powering measuring transducers.
-
Product
GC Detectors
-
Compact and modular, the new, second generation 5383 Pulsed Flame Photometric GC Detector (PFPD) offers greater ease of use, design flexibility, and analytical refinement than its predecessor, while retaining the proven technology features that laboratories around the world rely on for accurate results.
-
Product
Powerful Demagnetization Unit For Components
ZMAG CM
-
Foerster Instruments, Incorporated
To avoid this, FOERSTER offer a powerful demagnetization unit: the ZMAG CM. The pulse method used enables high penetration depth to demagnetize the components effectively and promptly. The Siemens control and pre-configuration allows an easy integration of the unit into your production process. Thus, your process quality and reliability can be significantly increased.
-
Product
Advanced Pulsed-RF Measurements
S93026B
-
S93026B advanced pulsed-RF measurements includes all the capability of S93025B (four internal pulse generators) and adds narrowband-pulse-detection method to extend pulse measurement capability in point-in-pulse and pulse-profile measurements.
-
Product
High Voltage Measurement
-
High Voltage Pulse Attenuator is used to attenuate high voltage pulse signals in a 50 system. It is consist of highly surge robust components with great voltage linearity. The device is symmetrical, Input and output can be exchanged.
-
Product
Pulsed X-ray technology
-
Golden Engineering X-ray generators are based on Pulsed X-ray technology. Pulsed X-rays generate a high intensity X-ray burst (pulse) in a very short period of time (10 to 50 nanoseconds depending on the model). The output dose of each pulse is 3-6 mR measured 12 inches from the front of the X-ray generator. The operator varies the overall dose of each exposure by changing the pulse setting. The pulse rate varies from 10 pulses per second to 25 pulses per second depending on the model. The generators can fire up to 200 pulses before a four-minute rest period.
-
Product
Internal Antennas
-
Pulse offers a large selection of internal antennas that are designed into an incredibly diverse selection of solutions, from smart home IoT devices to utility meters, from point of sale products to wireless charging. The PCB antennas, including those made with flexible material, are made to be mounted or adhered against a plastic surface and connect via cable to your PCB, and cover the ISM, WiFi, GNSS, and cellular bands. The NFC selection for 13.56 MHz will work with both 50 and 80 Ohm radios and include antennas with a ferrite backing to work even when mounted against metal. The selection of active GNSS patch antennas with cable are perfect for ensuring your device’s whereabouts are accurately tracked. Finally, the many transmit and receive coils for wireless power charging will add this popular consumer capability to your product, cutting one final cable from design. Use the product finder below to find the perfect internal antenna solution for you.
-
Product
10 MHz To 6 GHz LAN Wide Dynamic Range Average Power Sensor
L2051XA
Power Sensor
Frequency range of 10 MHz – 6 GHzLAN connectivity with a wide dynamic range of -70 to +26 dBm for small signal measurementsFast real-time measurement of 50,000 readings/secReal-time measurement with zero dead time to ensure every single continuous pulse is measuredAverage mode time-selectivity function allows full dynamic range for average and time selectivity average power measurementsInternal zero and automatic calibration saves time and reduces measurement uncertaintyA BenchVue software license (BV0007B) is now included with your instrument. BenchVue makes it simple to connect, control instruments, and automate test sequences
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
GPIB Interface Card
PI-31000
-
The Pulse Instruments PI-31000 IEEE Interface Card is a standard GPIB Interface card offered by National Instruments. This interface card is used in applications where the PI-2005 Pattern Generator or other instruments are controlled from a remote system CPU, or it can be used as the system controller when the CompactPCI CPU is the system computer.
-
Product
Electronic Instruments
-
The ORTEC range of modular electronics includes instruments in NIM formats as well as other modular instruments, such as photomultiplier bases, preamplifiers and other accessories. ORTEC also offers modular instruments for pulse height spectroscopy, fast timing, counting, high voltage power supplies and other special functions.
-
Product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
-
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
Product
MMIs for Test and System Integration
-
Laying out a custom PCB is too time consuming and costly for most rush projects. Pulse Research Lab has developed Mini Modular Instruments ™ to provide cost effective solutions to the most common engineering challenges.
-
Product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
