Device Programmers
Program non-volatile memories, logic devices, microprocessors and other electrically-programmable devices.
See Also: Programmers
-
Product
In System Programmers
-
In-circuit serial programming, also known as in-system programming (ISP) or in-circuit programming (ICP) enables programming and reprogramming of microcontrollers, serial EEPROMs and flash memories already soldered on a target PCB.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-341-HI
Programmable Resistor Module
The 40-230-341-HI (PXI) and 42-230-341-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 102kΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Active Device Characterization Solution Up To 50 GHz For 5G
N5245BM
-
The N5245BM provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for active device characterization up to 50 GHz for 5G applications.
-
Product
PCI Precision Resistor Card 4-Channel
50-297-130
Precision Resistor Module
The 50-297 PCI precision resistor provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 range is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
IEC60558 Insulation Material Layer Abrasion Resistant Test Device
CX-J16
-
Shenzhen Chuangxin Instruments Co., Ltd.
This test is conforms to IEC60558-1 Fig6 and IEC60065 Fig14--16.The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-151
Programmable Resistor Module
The 40-297A-151 (PXI) and the 42-297A-151 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710-5V-I
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785650-02
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
PoKeys I/O devices
-
This board allows expanding the number of outputs of the Pokeys by using the PoExtBus. This board incorporates 16 high current/voltage open collector outputs which suits applications such as lamps, relays.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-133-HI
Programmable Resistor Module
The 40-230-133-HI (PXI) and 42-230-133-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Photonic Device Testing
-
ficonTEC’s series of photonic device testing machines is focused on automated electrical, optical or mixed-signal electro-optical characterization (test-&-qualify) of chips and dies, opto-electronic assembles and integrated devices. Capability includes PIC design validation and device verification.
-
Product
Medium Power Programmable DC Electronic Load(600W~3000W)
FT63200A/E
-
Shenzhen FaithTech Technology Co., Ltd.
The FT63200A/E series of Medium power programmable DC electronic load is designed for high reliability and high power density. It can achieve 2U/3kW, which is twice of the power density of the conventional load. The FT63200A/E series has three voltage ranges of 150V, 600V and 1200V, with a single power range from 750W to 3kW. Its wider working range, extremely fast dynamic frequency, effectively increase the testing capability and application range. The whole series of products have strong overload capacity, instant over power pull up to twice the rated power, can effectively reduce the test cost.
-
Product
PCI-8532, 1-Port, DeviceNet Interface Device
781062-01
Interface
The PCI‑8532 is a high-speed DeviceNet Interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the controller area network (CAN) physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. The DeviceNet specifications are managed by OVDA, Inc. You can program the PCI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
High-accuracy Dual-channel Programmable Battery Simulator
N8352 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8352 series is specially designed for the R&D and testing of portable, battery-operated products , such as Bluetooth headsets, mobile, AR/VR smart terminals, electrical tools, etc. The current flows in both directions and can be used as either a power supply or a load. N8352 is easy for operation with touch screen and UI design. The output features are comparable to actual batteries, with fast dynamic response, no overshoot in voltage rise and fall, and stable waveform. The resolution is up to nA level, which can test the loop static power consumption, etc. N8352 can be widely used in the area of consumer electronics testing.
-
Product
PCIe-6537B, 32-Channel, 50 MHz, 200 MB/s Digital I/O Device
782631-01
Digital I/O Module
32-Channel, 50 MHz, 200 MB/s Digital I/O Device - The PCIe-6537 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-020-HI
Programmable Resistor Module
The 40-230-020-HI (PXI) and 42-230-020-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 472Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm
50-294-013
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-041-HI
Programmable Resistor Module
The 40-230-041-HI (PXI) and 42-230-041-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-053-HI
Programmable Resistor Module
The 40-230-053-HI (PXI) and 42-230-053-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 11.32MΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-252-010
Programmable Resistor Module
The 40-252-010 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
-
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
GPIB-USB-HS, USB, IEEE 488 GPIB Instrument Control Device
778927-01
GPIB Controller
USB, IEEE 488 GPIB Instrument Control Device - The GPIB‑USB‑HS is an IEEE 488 controller device for computers with USB slots. The GPIB‑USB‑HS achieves maximum IEEE 488.2 performance. With no GPIB cable required for instrument connection, you can use the Hi‑Speed USB port to control up to 14 programmable GPIB instruments. This device is completely IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-041-HI
Programmable Resistor Module
The 40-230-041-HI (PXI) and 42-230-041-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
FD-11614, 16-Channel Temperature Input Device for FieldDAQ
785854-01
Temperature Input Module
The FD-11614 measures up to 16 thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11614 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11614 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11614 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
Product
Bus Analyzer, Monitor, Debugger & Programmer
BusPro-I™
-
The BusPro-I has all the power, flexibility, and features you need to monitor and debug the I2C bus circuitry on your board. The BusPro I2C can be used to monitor and log I2C bus traffic in real-time, generate I2C transactions to communicate with peripheral components on the bus, and in-system program I2C compatible EEPROMs.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-350-HI
Programmable Resistor Module
The 40-230-350-HI (PXI) and 42-230-350-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Smart Device Testing
-
Helping you ensure that your smart devices with integrated wireless modules meet requirements to demonstrate compliance to global wireless type approval requirements.A smart device is any piece of electronic equipment that intentionally communicates and interacts with other electronic devices using wireless protocols. In order to verify the performance and connectivity of these devices, both the device hardware and the communication protocol are evaluated to ensure smooth connectivity and eliminate unacceptable interference.
-
Product
Mature & Discontinued Devices
-
The product families on this page have been classified as "Mature". In most cases there is a newer technology product family that will better meet the needs of today's system logic designers. Designers working on new designs are strongly encouraged to evaluate the alternative product families listed in the "Use for New Designs" column. Unless a Mature Family has been formally superseded via our Product Change Notification (PCN) procedure Lattice will continue to support existing business for these Mature products. Certain of the products for which the PCN process has been completed have been transferred, as indicated in the table, to Rochester Electronics or Arrow Electronics. Please contact those companies for availability of the products indicated.
