-
product
X-Ray And Gamma Detector Systems
The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.
-
-
product
X-Ray Detector
XRT Detector Onyx
ONYX 1412-X is a performance-leading X-ray detector comprising a proprietary 2768 × 2376 active pixel sensor array of 50 × 50 µm pixels. This detector consists of a high-speed, low-noise, radiation-tolerant, 14 × 12 cm, 6.6M pixel CMOS image sensor, with a directly deposited high-resolution CsI scintillator on Fibre Optic Plate. The highly configurable sensor is accessed through a software interface, connected via a 10 GbE SFP+ hardware interface.
-
product
Clamping Voltage Tester
MIG0603CLV1
The MIG0603CLV1 is a generator for testing varistors. It has circuits with three different source impedances and up to 11 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 200A which is maintained over the entire load range.
-
product
Voltage Meter
MN6SV
The M-module is intended for use as part of an automated measuring system for monitoring any object, the output signal of which is high voltage, for example, telemetry circuits, etc.
-
product
Voltage Variable Attenuators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
High Voltage
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules. The flexible high voltage design platforms and responsive management structure enable us to offer an economically viable custom build. High voltage power supplies from ETPS are used in a variety of applications ranging from electron acceleration systems and mass spectrometers to magnetrons, x-ray and nuclear research.
-
product
Protected Voltage Relay
PVR
Type PVR voltage-acuated relays are designed for indication alarm or annunciation in electric utility applications. They are used for data inputs to supervisory control/data acquisition and sequntial event recorders.
-
product
Smallest Multimetric Nanoparticle Detector
partector 2
Naneos Particle Solutions gmbh
The naneos partector 2 is the world's smallest multimetric nanoparticle detector. The partector 2 uses dual non-contact detection stages to measure not only lung-deposited surface area like the partector 2 Light, but also particle number concentration and average particle diameter. Additionally, ultrafine particle (UFP) surface and ultrafine particle mass concentrations are calculated and displayed. In contrast to some of our competitors, the UFP mass is displayed online, and it is calculated using the measured diameter of the particles, rather than estimated by a simple multiplier for LDSA.
-
product
CO Detector
6602
Peaceful Thriving Enterprise Co Ltd
This detector is design to detect the concentration of CO within the environment. The concentration of CO will be indicated by LED and buzzer voice. It's a helpful appliance for home, room and factory detection.
-
product
Low Voltage Regulation
The low voltage regulation system LVRSys represents a cost effective alternative for grid expansion. The economic use is recommended in all low voltage grids where short-circuit power is sufficient, but have voltage maintenance problems.
-
product
Underwater Metal Detector
5000
Littlemore Scientific Engineering Co
Robust diver held detector capable of operation to 200 Meters (660ft).Supplied ready for use with rechargeable battery, clacker earphone, standard 25cm coil, mains charger and user manual.
-
product
AE Valve Leakage Detector
SVLD1
Through acquisition, processing, and calculation of acoustic emission signal of the valves, SVLD1 could generated root-mean-square voltage (RMS), average signal level (ASL) and power (P) parameters as which could judge the leakage. Meantime, you can pre-calibrate the leakage quantity for the specified valve, and calibration curve of parameters and leakage could be calculated by SVLD1, so as to give the valve leakage reference value during the test.
-
product
Voltage Controlled Oscillators
Mercury Systems’ VCOs (Voltage Controlled Oscillators) offer predictable consistency, rugged design and reliable performance. Our VCO products will meet your application’s most demanding stability and low phase noise requirements; featuring wide tuning bandwidth up to an octave. With custom designs and space qualified versions, trust Mercury to provide the VCOs for your next design.
-
product
Ultrasound Detector
D200
A heterodyne detector with backlit, large digit, accurate digital display, showing the tuned frequency in the heterodyne mode. The frequency and volume controls are on the side of the case, making it easy to adjust.
-
product
Panel-mounted Voltage Power Amplifier
PAV120Bi
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
product
Pinhole Detector
270
The Elcometer 270 Pinhole Tester range utilises the wet sponge technique and has been designed to set a new standard for wet sponge pinhole detectors.
-
product
High Voltage Probes
High voltage measurements have a variety of different requirements, and our PVM series and VD series probes are designed for most of these requirements. The PVM probes are designed for wide bandwidth and ease of portability where a variety of measurements must be made. The VD series probes are designed for use at higher voltage ranges, and where physical stability is required.
-
-
product
Low Voltage Cable Tester
1100R+
The 1100R+ bench top cable tester packs impressive capabilities into a package that is small, affordable, and intuitive. The large display and sensible button interface make cable testing quick and easy. Test Point Range: 128-1024, Test Voltage: 5VDC 6mA max current.
-
product
Multi-spectrum Infrared Flame Detector
975MR
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
product
Fluorescent Powder Color Detector
Shanghai Yiya Electronic Instrument Co., Ltd.
Useful testing tool for detecting the color of fluorescent powder tubing.- Safe and reliable.- Mini design more portable. - Safe on button design with accidental turn -on protection.
-
product
Voltage Controlled Oscillators
Teledyne RF & Microwave offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
product
H.V. Detector
276 HD
Standard Electric Works Co., Ltd
● Telescopic, compact, lightweight● High voltage and Low voltage detection● Self-test button● Easy-to-recognize indication ● Waterproo
-
-
product
Non-Contact H.V. Detector
300 HP
Standard Electric Works Co., Ltd
Protection class : IP66. 3 LED indicators in a circle for easier viewing in any directions (360° LED indication). 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV. High bright LED visual indication. With the longer shelter to make the 3 LED indicators brighter under the sun. Sound indication. The maximum voltage setting can be 500kV . Self-test function. Power source : 1.5V "C" type battery × 3. High impact nylon casing. Non-contact work by proximity. Compatible with most hot sticks. Lightweight, robust & compact. Suitable for indoor and outdoor use. Easy access to batteries. Special ranges are available upon request. The maximum detection range can be 500kV. Meets EN 61326-1, CISPR 11, EN 61000-4-2, EN 61000-4-3, EN 61000-4-8.
-
product
Series Voltage References
Analog Devices offers a broad line of series voltage references with low dropout, low power, and excellent line regulation. These devices are voltage references that are functionally similar to a three-terminal regulator. Some series voltage references are designed to also operate in shunt mode by biasing the output pin and leaving the input pin open circuit. Series mode voltage references have the advantage that they draw only load and quiescent current from the input supply.
-
product
Gas Detectors
At PCE Instruments you will find a professional quality gas detector / gas detection instrument for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
-
product
Relay Testing Voltage Source
PTE-FCN
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
product
Ground Fault Detectors
STB Electrical Test Equipment, Inc
STB's convenient Ground Fault Detectors may be operated with one hand and are ideal for preventative maintenance. Ground Fault Detectors indicate ground faults and electrical leakage while equipment is in operation.
