Well
-
product
Bi-Axial or Axial Averaging Extensometers
Model 3560
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
PCIe FPGA Carrier For FMC, Virtex UltraScale™
PCI595
The PCI595 is based on the Xilinx XCVU440 Virtex UltraScale FPGA, which provides 2,880 DSP slices, 88.6 Mb RAM and 5,541,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to one DDR4, 64-bit wide, with 8 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
product
Extensive Qualification & Test
Quality and reliability of the battery pack design starts with proper cell selection. Ensuring the battery pack is well matched to the host equipment is often overlooked or not given sufficient priority until performance and/or supply problems occur. Proper cell selection is key and requires much more than checking dimensions and capacity. Designers need to consider loading, environment, shelf life, and a number of other factors specific to the application.
-
product
Electromechanical Testing Machines
Stand model in four-pillar design with electronic force transducer, flanged to the movable testing machine crosshead and electronic position transducer for measuring the crosshead path. The machine is driven by a quartz-precise stepper motor with two ball screws. Complete with integrated displacement measuring device 0.01 mm over the entire travel distance as well as additional displacement transducer with connecting cable and holder
-
product
Human Radiation Spectrometers
Human radiation spectrometer is designed for express control and measurement of the activity of 137 Cs and 134 Cs gamma-emitting radionuclides in the human body, as well as for assessing the internal radiation dose (“sitting in a chair” geometry).
-
product
PICMG 1.3 Full-size CPU Card With LGA1151 8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150
The SHB150 is based on the latest LGA1151 socket 8th generation Intel® Core™ processors (code name: Coffee Lake) and Intel® C246, Q370 or H310 chipset. The SHB150 features multiple I/O options and high-speed transfer interfaces as well as superior graphics capability (Intel® HD Graphics), making it an ideal solution for smart factory automation. The Intel® Core™-based full-size SBC, SHB150, comes with two 288-pin DDR4-2666/2400 Long-DIMM sockets with up to 32GB of system memory. The PICMG 1.3 single board computer has a maximum of six SATA-600 ports supporting software RAID 0/1/5/10 for data redundancy. It also has one M.2 Key M 2280 SSD slot with a PCIe x4 interface. The SHB150 with the Intel® HD Graphics brings a true high definition visual experience with triple display configurations (Intel® C246 or Q370) via DVI-I and DisplayPort (header) ports. Moreover, the Intel® Coffee Lake-based SHB150 supports optional Trusted Platform Module (TPM) 2.0 for optimum security, Intel® Active Management Technology (Intel® AMT) 12 for remote management, as well as Intel® vPro™ technology. The industrial single board computer provides significant advantages to customers in the fields of machine vision and industrial automation operations
-
product
Cable Test And Fault Location Systems
Power outages can cause serious financial and social damage, as they disrupt the normal operation of security and life support systems, destabilise the operation of industrial facilities, transport network, and utilities. Reliable power distribution is ensured by an effective prevention and prompt elimination of cable faults and electrical equipment failures. KharkovEnergoPribor Ltd. offers a range of integrated solutions designed for testing power cables and electrical substation equipment, as well as locating various types of faults in underground utilities.
-
product
PCIe-6321, PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device
781044-01
PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6321 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6321 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 5.82MΩ
50-298-052
The 50-298-052 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Diode Driver & Laser System Controllers
The laser controllers provide a simple method of controlling Lumina and other popular laser diode drivers or full laser systems. They include the ability to easily control current levels, pulse modes, and interlock controls as well as monitor voltage and current levels as well as q-switch triggering, external triggering, sync output, and additional I/O signals.
-
product
Signal, Module, Receiver, TriPaddle, 64 Position, w/ Right Angle Contacts
510104109
Primary mating module 510108101. (May mate with other ITA modules, as well.)
-
product
PXI Precision Resistor Module 6-Channel, 3 to 1.51M
40-297-050
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
C Series Voltage And Current Input Module
The C Series Voltage and Current Input Module features up to 16 input channels with built-in noise rejection. You can use this module to combine the two most common inputs to reduce the overall number of modules you need in your measurement system.The C Series Voltage and Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
product
Battery Voltage Recorder
BVR Series
Battery voltage recorders from BVR series are designed to serve as a support tool for cell voltage measurement during battery capacity testing.During capacity testing, cell voltage, temperature, inter-cell connection voltage, and specific gravity should be measured in order to determine failling cells in the string that should be replaced.Furthermore, IEEE standards for stationary batteries applications stipulate periodical measurement of overall string voltage, as well as cell voltage and temperature.The BVR Series is the perfect tool for that purpose. All measurements are automatically saved in device’s internal memory. Additionally, DV-B Win software helps the user to download all measured results. Furthermore, the user can create test reports and export them to various formats.BVR series includes two models: BVR11 and BVR22. These are rechargeable handheld devices intended for performing monthly battery inspections and support tools during capacity testing. The list of the applications of these instruments includes:Efficient supplement to BLU series of battery load units during battery discharge testingMonthly inspections of large battery banksAmbient temperature measurementCurrent measurement using current clampsUSB and Bluetooth communication with PCSimultaneous string voltage and current measurement to analyze a discharge test processThe BVR22 model provides Bluetooth communication with an external density meter, for transferring electrolyte specific gravity and temperature readings.
-
product
7/16 DIN Connectors
Pasternack 7-16 DIN connector category includes many part numbers, most are RoHS and REACH compliant. 7-16 DIN connector series in this category will terminate to coax or terminal. Our 7-16 DIN connectors are built to precise industry specifications. 7/16 DIN connector items are available in male or female gender with 50 Ohm impedance. 7-16 DIN connectors are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. These DIN 7-16 connector designs include clamp/solder, crimp/solder, field replaceable or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 7/16 DIN connector series is in-stock. Not only are the 7 / 16 connectors in stock, but they will also ship the same day as they are purchased.
-
product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine the multi-channel SA with the internal swept-signal generators. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
product
Open Pluggable Specification-Plus (OPS+) Digital Signage Player With LGA1151 Socket 8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q370 And TPM 2.0
OPS700-520
The OPS700-520 is an Open Pluggable Specification Plus (OPS+) digital signage player. The high-performance signer player is powered by the high-performance LGA1151 socket 8th generation Intel® Core™ i7/i5/i3 and Celeron® processors (codename: Coffee Lake S) with the Intel® Q370 chipset. This OPS+ digital signage module supports Trusted Platform Module (TPM) 2.0, Intel® Active Management Technology (Intel® AMT) 11.0 as well as Intel Unite® solution for content sharing and collaboration. It comes with two 260-pin DDR4-2400 SO-DIMM sockets that can provide system memory of up to 32GB. The Coffee Lake S-based OPS700-520 offering future-proofed flexibility and performance is among one of the most advanced and powerful digital signage players in the market.
-
product
Triaxial Linear Accelerometers
Columbia Research Laboratories
The Triaxial Force Balance Linear Accelerometers range from general purpose, low cost sensors, capable of measuring DC and low frequency acceleration simultaneously in three axes, to Miniature Airborne, Highly Reliable Sensors that operate from +24 to +32VDC Aircraft power. Also offered are compact, premium performance, extremely rugged sensors, well suited for demanding missile and airborne applications.
-
product
Flow Management
HR7100
HighReach Measuring & Controlling System Co.,Ltd
HR7100 series intelligent electromagnetic flowmeter is a fully intelligent flowmeter developed and developed by our company using the most advanced technology at home and abroad. It has the characteristics of high measurement accuracy, high reliability, good stability and long service life. Pay attention to every aspect In the process of designing product structure, material selection, manufacturing process, production assembly and factory testing. We have a water tower of up to 35m as a steady-state flow regulator, as well as a professional electromagnetic flowmeter production equipment line. Designed and developed large-scale production software and hardware for electromagnetic flowmeters to ensure long-term high quality.The product is designed with Chinese and English liquid crystal display with wide backlight and full-featured function. It is intuitive to display, easy to operate and use, and can reduce the trouble of on-site installation and maintenance. Widely used in petroleum, Chemical, metallurgy, water supply and drainage, steel, coal, paper, food, textile, environmental protection and other industrial sectors and municipal management, water conservancy construction and other fields.
-
product
RF & Microwave Power Meters
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
product
Acoustic Analysis
Noise is increasingly the subject of new regulations for the protection of human health and safety as well as for improving the environment in general. As well as sound levels, the perceived sound quality of products from washing machines to vehicles is often an important part of the customer buying decision so must be considered during product development. m+p Analyzer for noise and vibration measurement and analysis provides a full range of capability for these applications. Real-time fractional octave filters satisfy all acoustic applications from simple sound pressure, sound power for equipment legislative requirements, intensity mapping to isolate sources to sound quality metrics for product refinement.
-
product
Sensor
Lepton
The FLIR Lepton™ is the most compact longwave infrared (LWIR) sensor available as an OEM product. It packs a resolution of 80 × 60 or 160x120 pixels into a camera body that is smaller than a dime. This revolutionary camera core is poised to equip a new generation of mobile and handheld devices, as well as small fixed-mount camera systems, with thermal imaging capabilities never seen before. Lepton contains a breakthrough lens fabricated in wafer form, along with a microbolometer focal plane array (FPA) and advanced thermal image processing. In order to support the lepton and make it easy to use, we have developed a breakout board to support the module along with example source code. Please see the Lepton Thermal Camera Breakout Datasheet for more information.
-
product
Top Loading Industrial Ovens
Gruenberg manufactures two, specialty industrial top loading ovens that are designed for multiple processes, including annealing, preheating and baking. Their rugged durability are well suited for oil and gas applications. Standard and custom options accommodate a variety of processing applications including drying, curing, baking, aging and more.
-
product
Dynamic Component Test Systems
RedViking brings advanced engineering and proven implementation expertise to your next dynamic component test stand. We’ve designed entire fleets of multi-model and single-model test systems for new component development and production as well as military and commercial MROs. We have decades of experience building and implementing turnkey dynamic component test systems, and we’ll work with your teams virtually anywhere in the world.
-
product
ArgoBot Kit
ROB-00001
The ArgoBot Full Kit is a fully assembled robot and controls development platform. It is based on the Digilent chipKIT WF32(TM), a WiFi enabled development platform, and configured for LabVIEW targeting. Most importantly ArgoBot was designed with FIRST Robotics Competition teams in the front of our minds! Named after the FRC Team 1756 mascot, Argos, the ArgoBot development platform includes a fully-assembled, ready to drive mini WiFi enabled robot (about 8" x 5" x 4"), as well as tons of FRC controls tutorials and example code (LabVIEW VIs). Features included on the ArgoBot will look very familiar to anyone who has worked with National Instruments products (Compact RIO and RoboRIO) in the past. This includes three 5V Digital I/O modules (with jumpered pull-ups), three 5V analog inputs, and an I2C header. Example VIs have been streamlined to enable a 1-click configuration style to accelerate your development process. We also added a 2-channel motor driver that is used to supply the ArgoBot drive motors. Our ultimate goal is that everything you can build, control or implement on ArgoBot can be easily leveraged on your FRC bot! Complimenting its many electrical features, ArgoBot is easy to work with and easy to maintain. The chassis is a polycarbonate (the extremely tough stuff that is easy to drill and modify but easily takes bumps and bruises without cracking) case that is fully intact - meaning that ArgoBot doesn't just come with a case... it is a case! Clean-up and organization is simple - just close the case and turn off the power switch.
-
product
75 Ohm SMB Connectors
Pasternack 75 Ohm SMB connector category includes dozens of part numbers, most are RoHS and REACH compliant. 75 Ohm SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB 75 Ohm connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm SMB connector products are built in jack or plug gender with 75 Ohm impedance. SMB connectors in 75 Ohm impedance are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm SMB connector series is in-stock. Not only are these connectors with 75 Ohm SMB in stock, they will ship the same day as they are ordered.
-
product
NVIDIA® Jetson™ TX2-based Industrial AI Smart Camera for the Edge
NEON-2000-JT2 Series
ADLINK's NEON-2000 Series of the NVIDIA® Jetson™ based industrial AI cameras, integrate the Jetson™ Xavier NX or Jetson™ TX2, image sensor, optimized OS, and Rich I/O for vision applications in a compact chassis with verified thermal performance, saving users' Total Cost Ownership on integration and trouble shooting, as well as minizing footprint and cableing required for installation.
-
product
Digital AC milli Volt meter
PGP Electronics Private Limited
PGP Electronics Digital AC Mill voltmeter is a very versatile and general purpose equipment for the measurement of audio frequencies. It is useful in measuring low amplitude signals over a wide band of frequencies with precision. Its has a wide band width and sensitivity is 10uV. This instrument is useful for all amplifiers/ audio system manufacturers, college laboratories to measure input/output of any amplifier as well as frequency response of that amplifiers. .
-
product
Raman Spectrometer
IndiRAM CTR Series
CTR series Raman Spectrometer is a state-of-the-art Raman Spectrometer with an unmatched capability to identify a broad range of materials, as well as to quantify material concentrations at femto-molar level. The system comprises of one or more laser sources, an imaging spectrometer, TE cooled (-10oC / -60oC) CCD camera, an optical magnifying lens with a spatial resolution < 1µm. The CTR series Raman Spectrometer offers unparalleled sensitivity and resolution, making it ideal for nanoscale analysis and intricate molecular investigations. Easy to use, Microsoft Windows-based control and data processing software enables the user to comfortably operate the spectrometer.
