A/D Converters
quantization of an analog signal into a digital signal.
-
Product
Octal 4 Gsps 12-bit ADC
ADF-O4012
-
The DEG ADF-O4012 FMC includes eight 12-bit, 4 Gsps RF analog-to-digital converters (ADC). The ADF-O4012 features a 16-lane, 24.75 Gbps JESD204C interface, flexible clocking and triggering options. This ADF-O4012 leverages two Analog Devices AD9209 MxFE (Mixed Signal Front End) ICs, elevating the technology to a new level of integration.
-
Product
Isolated RS-232 To RS-422/485 Converter
ADAM-4520
-
Automatic RS-485 data flow control3000 VDC isolation protectionSurge protection RS-485 data lineTransmission speed up to 115.2 KbpsLED indicator to monitor status
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Power Supplies & Adapters
-
Curtiss-Wright Defense Solutions
Curtiss-Wright manufactures rugged DC/DC converter boards for stackable PC/104 and other small form factor embedded systems applications. Capable of supporting -40/+85°C extended temperature operation and high shock/vibration environments, these power supplies are routinely installed in vehicle and aircraft systems.
-
Product
Electrical Probe Systems
-
INSTEC's Probe Systems offer an integrated solution for performing component-level electrical measurements over a wide temperature range.Compact Mini Probe Stages enable an existing inspection microscope or optical test setup to be converted easily into a precision temperature-controlled semiconductor testing and qualification station.Analytical probe stations are fully featured industry-standard platforms for all modern probing applications and testing.Benchtop Probe Stations provide the user with four independent electrical probes with X,Y,Z micropositioning for precise placement without opening the sample chamber.Highly configurable probe systems meet a range of requirements for atmospheric and temperature control, sample areas, and electrical measurements.
-
Product
Mini PoE+ Media Converter, 1000Mbps, SFP (Also Known As MiniMc 857-11911TG)
IMC-390-SFP
-
Supports IEEE802.3at PoE+ (25.5W) and IEEE802.3af PoE (15.4W) standardsServes as a power sourcing equipment (PSE) deviceSupports jumbo frame functionality (up to 10240 bytes)Supports multiple mounting options (desktop, DIN rail or wall-mount)Features in configurable PoE reset on fiber LOSSupports Link Fault Pass Through (LFPT)
-
Product
THERMO & A/D MODULE OF THE COMPACT DEVICE FAMILY
ES650
-
Featuring 16 electrically insulated measuring channels for analog voltages and an adjustable acquisition rate per module, this module provides high measuring accuracy through 16-bit (A/D) or 21-bit (thermal) resolution. Signal smoothing occurs through a parameterized software filter, and offers two selectable measuring ranges of 10 V and 60 V. The automotive measuring range is -210 C to 1372 C (-346 F to 2502 F). Data transfer to PC occurs via Ethernet.
-
Product
Thermal Voltage Converter
1395D
-
The 1395D series of TVC's, have Dual Thermal Element technology. The 1395D offers double the output voltage (typically 14 mV instead of 7 mV). This higher output voltage means better resolution and increased accuracy. It can be used to measure AC Voltages between 20 Hz and 100 MHz and it can serve as a primary AC voltage standard and/or standard for calibration of AC calibrators and voltmeters.
-
Product
300 HP Complete Bench Hydraulic Test Center
HTC-300
-
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 300 hp (224 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators). The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
Product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
Multifunction I/O
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
RF Power Amplifiers
-
RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99
-
Product
Real-Time Analysis, 255 MHz, Basic Detection, Multi-touch
N9040B-RT1
Signal Analyzer
See, capture, and understand elusive signals as short as 17.17 s with 100% POI and a complete set of advanced triggers View signal dynamics with integrated real-time displays Maximize your investment by adding RTSA at a fraction of the cost of a dedicated solution Easily integrate the 89600 software and thoroughly analyze complex signals Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Sanitary Conductivity Sensor (Ferrule Clamp Type)
FES-210L
-
The FES-210L Series sanitary conductivity sensors are electric sensors that target sanitation issues by employing a flat structure that keeps dirt from adhering to the tip of the sensor, and they enable continuous, high accuracy measurement in liquids of various concentrations, from purified water to cleaning solutions.The FES-210L Series, which is used in conjunction with the conductivity converter HE-960HS, demonstrates the optimum high sanitary characteristics that are ideal for the concentration and CIP management employed at food (beverage) and cosmetics plants.
-
Product
DC Electronic Load
-
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
Product
Isolated Process Control Signal Conditioning Products
SCIM7B
-
SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.
-
Product
Temperature and Humidity Regulator
H3331-2
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Gateways And Bridges
FarLinX Connect Mini v2
-
A compact remotely manageable HDLC Bridge and TCP to HDLC Converter.
-
Product
Titration
-
A typical titration begins with a beaker or Erlenmeyer flask containing a very precise volume of the analyte and a small amount of indicator placed underneath a calibrated burette or chemistry pipetting syringe containing the titrant. Small volumes of the titrant are then added to the analyte and indicator until the indicator changes, reflecting arrival at the endpoint of the titration.
-
Product
4-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - PCIe
Model 78664
-
Model 78664 is a member of the Cobalt family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A multichannel, high-speed data converter withprogrammable DDCs (digital downconverters), it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture feature offers anideal turnkey solution. The 78664 PCIe output supports fully the VITA 49.0 Radio Transport (VRT) Standard.
-
Product
8-Channel 200 MHz A/D with DDC, Kintex UltraScale FPGA - 6U VPX
Model 58861
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Eight 200 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PCIe-7858, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device
786457-01
Multifunction Reconfigurable I/O
PCIe, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7858 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7858 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
Scanners
TK91A
-
BK Mikro TK91A is a scanner designed mainly for broken tool detection inside the tool changer of machining centers adding little or no additional cycle time. The controller stores up to 512 different tool lengths in memory and is controlled using M-Code combinations, a custom Macro or Profibus. The system can check tools whose lengths vary as much as 22 inches from the shortest to longest in the changer. Each of the 512 different tools can have individual tolerance ranges set varying between 0.05 and 25.4 degrees. This equates to as little as a 0.38mm difference in tool length variation that can be detected using a 500mm long wand.
-
Product
Heavy Duty Dynamometers
MD-250-HD
-
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.
-
Product
100 KS/s, 12-Bit, 16-Ch Universal Multifunction PCI Card
PCI-1711
-
16-ch single-ended analog inputCost-effective12-bit A/D converter, with up to 100 kHz sampling rate16 single-ended analog inputsProgrammable gain16 digital inputs and 16 digital outputs16-ch digital input and 16-ch digital outputTwo 12-bit analog output channelsOnboard FIFO memory (1,024 samples)Onboard FIFO memory (1024 samples)Automatic channel/gain scanningOnboard programmable counter
-
Product
DC current Sensors
CTH
-
The CTH sensors convert dc current to an isolated voltage output, the CTHR sensors convert ac current to a dc output signal proportional to the Arms. All popular process control voltage and current loop outputs are available. Through hole or split core options mean that connection is non-intrusive and straightforward. The available input range of the CTH sensors is any value from 5A to 6000Adc.
-
Product
Media Converter
-
Xtramus Industrial Instruments
Translates one type of network signal or cable media into another, such as connecting traditional copper Ethernet cables to fiber optic cables.
-
Product
Scientific CMOS Camera
Prime 95B
-
The Prime 95B Scientific CMOS camera allows you to overcome many difficult imaging challenges by converting nearly every available photon to useful signal through an incredible 95% Quantum Efficiency by using the first available scientific CMOS sensor with back-side illumination. The result is the most sensitive CMOS camera available for scientific imaging.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 4 Channels, 2.5 GS/s on 8 Channels, 1.25 GS/s on 16 Channels
DN6.225-16
Digitizer
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
System Components
-
System components and accessories complete the Bender product portfolio:Coupling devices for ground-fault monitoring at high voltages, analog measuring instruments, power supply units, interface converters and interface repeaters.Please contact us for advice regarding these and other system components.
