-
Product
Computer-On-Module
CM22301
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM22301 uses Intel® sixth-generation Skylake platform and Core M low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.1GHz and the display output resolution can be up to 4K. CM22301 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-performance fanless designs. CM22301 supports up to 16GB dual-channel low-voltage DDR3L memory populated onboard, and up to 64GB on-board solid state disk silicon, as benefit the development of ruggedized products for harsh environment applications.As defined by VITA 59 specification, CM22301 provides up to 6 PCIe lanes, enabling flexible functionality expansions, such as NICs, DAQs, video capture and so on. Meanwhile, CM22301 also provides up to date computer interfaces like GbE, SATA3, USB3.0/2.0, HD Audio, etc. CM22301 uses the same 220pin board-to-board connector and Type10 pin out definition as COM Express.
-
Product
Tri-phase High Power Programmable AC Power Source
APS50000
-
Advanced direct digital frequency sythesizer(DDS) waveform generation technology, high frequency stability, good continutyMeasurement precision is high, suitable for current half-sinusoid and its similar waveforms with DC component measurementProvide embedded intelligent PC monitoring systemAdjustable output voltage from 0 to 150V, 0 to 300V, step distance 0.1VOutput frequency 45-120Hz(40-500Hz optional), step distance 0.1 HzOutput current limiting functionWith 9 sets of memory, you can store commonly used parameters for easy invocation when using themWith RS232C communication interface 【IEEE488.0(GPIB)optional】, instruction execution times is less than 10mSProtechtion mode: over voltage, over current, overload, short circuit,current limit, ectProvide RMS voltage, RMS current, active power, frequency, power factor, ectFor 100% load removal, voltage stabilizing reaction time within 20ms, strong overload capacity, instantaneouscurrent can with stand 3 times of rated current
-
Product
Real-Time Open Check Hi-Pot Tester
DU3328
-
Delta United Instrument Co., Ltd.
Programmable test voltage in AC: 0.1K~5KV, DC: 0.1K~6KV Programmable cutting current in AC:0.001mA~15mA, DC: 0.001mA~7.5mA 3 in 1 functions, with AC, DC Hi-Pot test, Insulation test. Built in 100 sets memory Arcing detect function 8 ports scanning function Independent 8 channels real-time open check Real-time check function, to ensure your products tested, no more loss test.
-
Product
Vita42 Compact PCI PICMG 2.16 Blade
CP6007-RA
-
CP6007-RA is based on a sixcore Intel® Xeon® processor with 10nm technology, with outstanding performance-per-watt values. Its scalable power budget allows users to tailor the power dissipation to their requirements. 32GB soldered memory with ECC is provided.
-
Product
PICMG 1.3 Full-Size SBC With 14/13/12th Gen Intel® Core™ Processors And Intel® Q670E Chipset
NuPRO-E47
Single Board Computer
The NuPRO-E47 is a high-performance embedded single board computer that features with 14/13/12th Gen Intel® Core™ i7/i5/i3 processor and an Intel® Q670E Express chipset, which supports PCIe Gen 3. It comes equipped with 2 DIMM sockets that can support up to 64GB of Non-ECC DDR5 memory running at 4800MHz. The NuPRO-E47 also includes 6 SATA 3.0 ports with RAID support and 4 COM ports (including RS-232/422/485) for increased connectivity options. Additionally, the NuPRO-E47 supports Intel® PCIe bifurcation, allowing for flexible and efficient use of PCIe lanes. This single board computer is designed for use in a variety of industrial applications that require high-performance computing and reliable connectivity
-
Product
Multi-Function Transient Fault Recorder
TR-3000
-
The TR-3000 is the only tool you need to capture and diagnose power system anomalies. With multiple recording modes and continuous transient oscillography, you will never miss an event. The TR-3000 captures high speed transients and long term system disturbances with enough memory to give you a complete view of the system disturbance. The TR-3000 takes the place of several devices: • Fault and Disturbance Recorder • Transient Fault Location • Phasor Measurement Unit • Power Quality Monitor • Sequence of Events Recorder.
-
Product
HandyScope HS6-DIFF With SafeGround & SureConnect: 1 GS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-1000XMSG-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
Product
Thermometer
S0111
-
Thermometer is designed for record of temperature. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
Product
6U Compact PCI Single Board
CP62005
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62005 is a 6U CompactPCI® single board with high-performance, low power consumption and high reliability. It is ideal for ruggedized systems requiring high-bandwidth processing, or for information processing and embedded computing.CP62005 supports 4th generation Intel® Core™ i7 or i5 Haswell processors, up to 16GB onboard DDR3L memory. It also offers 16GB onboard SLC SSD for operating system and drivers. The onboard design of memory and SSD can enhance the anti-shock and vibration performance.CP62005 integrates Intel® HD Graphics 4600 controller, which supports a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA… CRT max resolution is up to 2048x1536. With HDMI/DP/eDP it can be up to 4K. It also supports three independent displays.
-
Product
Accelerometers
-
An accelerometer is used in manufacturing machine maintenance to inspect equipment vibration. An accelerometer also is used in product testing to measure the vibration of various components.A triaxial accelerometer, also called a 3-axis accelerometer, provides measurements of the following parameters: vibration acceleration, vibration velocity and vibration displacement. In this way, vibration is measured and recorded with great precision.Most accelerometer products offered by PCE Instruments are portable devices. Many feature memory functionality so that readings can be stored and retrieved later for in-depth analysis. Some accelerometer models come with a manufacturer's calibration certificate. Some accelerometer models can be calibrated to ISO standards optionally for an additional fee.
-
Product
4G Router
BB-SR30400021
-
SmartFlex, EMEA/LATAM/APAC, 2× ETH, Metal, ACC EU LTE cat.4, 3G/HSPA+, GPRS/EDGE, EMEA/LATAM/APAC, 2× SIM. LTE B1, B3, B5, B7, B8, B20, B38, B40, B41 Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
EEPROM
-
Renesas EEPROM realizes high speed, low power consumption and a high level of reliability by employing advanced MONOS memory technology, CMOS process and low voltage circuitry technology.
-
Product
Memory Test System
T5230
-
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
Super Fast Gang ISP Programmer
448Pro2
-
The Dataman 448Pro2 is a super fast PC based gang programmer with four independent 48-pin ZIF sockets, ISP capabilities and USB 2.0 connectivity • Up to 75% faster programming of high-capacity memory devices • Over 105,000 devices supported with new devices added monthly • Independent modules supporting concurrent programming • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Full ISP capabilities including JTAG compatibility • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5933-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
PCI Board
FastX1703-DIG
-
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
Product
3U CompactPCI Quad-Core Intel Atom® Processor X Series Blade
cPCI-3640 Series
Processor Blade
- Low power quad-core Intel Atom® x6413E Processor (formerly Elkhart Lake)- Up to 32GB DDR4-2400-3200MT/s ECC soldered memory- Optional onboard SSD support- Flexibility in IO selection- Extended temperature -40 to 85 degree C supported
-
Product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
ATCA PCIe Rugged Processor With Dual Xeon E5-26xx V4
ATC127
-
The ATC127 is a high performance ATCA processor blade featuring dual 14-core Intel® Xeon® processor (E5-2658 v4, E5-2680 v4, E5-2648L, 2618L, 2620 or 2630 v4), with eight banks of memory up to 256 GB DDR4 memory. Versatile connectivity includes two PCIe Gen3 x16 Fabric Interfaces, dual GbE Base Interfaces, dual front panel GbE egress Ports, front panel dual RS-232 and USB 3.0/2.0 Ports and front panel DVI-I connector. Onboard mSATA storage is available for local boot.
-
Product
Mini-ITX SBC With Intel® Celeron® Processor N3160 (up To 2.24 GHz) SoC, VGA/HDMI/LVDS, USB 3.0, Mini PCIe Card, MSATA And HD Audio
MANO300
-
The MANO300 mini-ITX motherboard built with the latest Intel® Celeron® processor N3150 (codename: Braswell) with integrated Intel® Gen 8 graphics supporting up to 4K resolution. Two SO-DIMM sockets are provided to support up to 8GB of DDR3L-1600 memory. The 12V single voltage DC power jack or ATX power makes the power input selection more flexible for different automation and embedded industries. Its friendly fanless cooling system design and compact form factor aimed at space-limited applications as well as harsh environments.
-
Product
Battery Voltage Recorder
BVR Series
-
Battery voltage recorders from BVR series are designed to serve as a support tool for cell voltage measurement during battery capacity testing.During capacity testing, cell voltage, temperature, inter-cell connection voltage, and specific gravity should be measured in order to determine failling cells in the string that should be replaced.Furthermore, IEEE standards for stationary batteries applications stipulate periodical measurement of overall string voltage, as well as cell voltage and temperature.The BVR Series is the perfect tool for that purpose. All measurements are automatically saved in device’s internal memory. Additionally, DV-B Win software helps the user to download all measured results. Furthermore, the user can create test reports and export them to various formats.BVR series includes two models: BVR11 and BVR22. These are rechargeable handheld devices intended for performing monthly battery inspections and support tools during capacity testing. The list of the applications of these instruments includes:Efficient supplement to BLU series of battery load units during battery discharge testingMonthly inspections of large battery banksAmbient temperature measurementCurrent measurement using current clampsUSB and Bluetooth communication with PCSimultaneous string voltage and current measurement to analyze a discharge test processThe BVR22 model provides Bluetooth communication with an external density meter, for transferring electrolyte specific gravity and temperature readings.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 4 Channels
M4I.6622-X8
Arbitrary Waveform Generator
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
Product
Multi-Interface Frame Grabber
Xtium2 CLHS PX8
-
Building on the field proven Teledyne DALSA’s Xtium family of frame grabbers, the Xtium™ 2 CLHS PX8 features CameraLink HS standard on the PCI Express™ Gen 3.0 platform. The Xtium2-CLHS supports Active Optical Cable (AOC) and industry standard CX4 cables. This single cable, single slot solution supports up to 7-CLHS lanes, each operating at 10.3 Gbits/s, to acquire images at up to 8.4 GBytes/s and transfer them using PCIe x8 slots to the host memory.
-
Product
Control Unit
Epec 5050
-
Epec 5050 Control Unit is ideal for applications that require plenty of I/O and enhanced algorithms. Epec 5050 control unit has also a large memory and its I/O is widely programmable. For example, PI pins’ threshold voltage can be selected and many inputs have pull-up/pull-down selection.
-
Product
PCIe3 AIC (NVMe) RunCore Consumer SSD “Sprinter Series”
-
RunCore Innovation Technology Co. Ltd.
Add In Card PCIe3 NVMe Solid State Drive (SSD) is a high capacity solid-state flash memory product that complies with the PCIe Gen 3 standard and is functionally compatible with a PCIe protocol.
-
Product
ECU Interfaces
-
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
Product
Infiniium S-Series High-Definition Oscilloscope: 2 GHz, 4 Analog Plus 16 Digital Channels
MSOS204A
Oscilloscope
2 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.5 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
USB Modular Oscilloscope, 100 MHz, 2 Analog Channels
U2701A
Oscilloscope
100 MHz2 analog channelsMore accurate analysis of electronic designs with deep 32 Mpts memory and high 1 GSa/s sample rateSimple USB setup with plug and play capabilityGet the debug power you need with advanced triggering, automatic measurements, math functions including FFTs and moreQuick and easy measurement configuration and acquisition with bundled Keysight Measurement Manager (KMM) softwareDocument results more easily using the high speed USB 2.0 interface
-
Product
Broadband Field Meter
NBM-550
-
*Intelligent probe interface detects probe parameters*Fully automatic zero point adjustment*Memory for saving up to 5,000 measurement results*PC software for convenient data management*Voice recording for comments*Conditional logging: Measured value saved when a threshold value is exceeded
-
Product
Relay Testers
-
Outputs 100VA single-phase voltage and 180VA single-phase currentEquipped with counter function, output selector, auto sweep function, memory function, DC output for testing, master/slave function, etc.Output frequencies of 50Hz, 60Hz, and 10Hz to 200Hz, using external synchronization or line synchronization (selectable)Equipped with GPIB/RS-232C interfacesWeight: 19.5kg
