-
product
Through Bore Slip Rings
Through Bore Slip Rings are used in applications where the customer requires the bore space for some other capabilities (cooling or air media; optical or RF channels, etc.). The Slip Ring can be designed to accommodate a wide variety of bore sizes.
-
product
Off-Line Base Test Platforms
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
-
product
Super MUTT Deluxe Standard Edition
#9008-SE
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
Analogue (1kV below) Insulation Tester
1131 IN
Standard Electric Works Co., Ltd
● Hight quality Taut Band movement.● Three insulation test voltages (DC) : 250V, 500V, 1000V.● Two ranges for continuity test : 2Ω & 20Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600Vac.● 200mA continuity short-circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
product
Flow Leak Testers
If you need high-quality air flow testers, you’ve come to the right place. We carry equipment for mass flow and leak testing, laminar flow, and continuous flow. You have the option of choosing touch screen or standard digital. All our equipment is compact and includes high-performing, state-of-the-art technology. Begin testing your equipment with our premium-grade flow testing equipment. Explore our amazing selection of flow testing equipment.
-
product
Testing LTE, And VoLTE
Long Term Evolution (LTE) is the so called 4th Generation (4G) mobile standard in the rapidly evolving mobile technologies. Its distinguishing feature is an all IP infrastructure and significantly greater air interface bandwidth to the mobile handset. It was developed as an enhancement to the existing 3G UMTS System (Universal Mobile Telecommunications System) to provide users enhanced mobile radio and internet access.
-
product
Level Detectors
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers selective RF level detectors for air interface monitoring. The detectors are especially designed for frequencies used in e.g. electron accelerators. Due its mechanical design, the modules are compatible to cable route mounting systems. The detection of unintentional RF radiation is a main application field.
-
product
Thermacon Request to Exit Sensor
T-80 and S-80
These units are designed for easy concealed installation in suspended ceilings or on an enclosed metal electrical box is acceptable for use in air handling areas. In addition to the four standard interchangeable detection patterns, others may be custom made.
-
product
Trailer Light and Air Brake System Tester
Express Mobile
The Express Mobile eliminates most of the walkingassociated with trailer servicing. When you eliminate all that non-productive time and effort, you can easily check all lighting functions and the air brake system (including brake adjustment) in just two minutes, start to finish.
-
product
HDC Torque Controllers
The HDC controllers operates with only the HD-Series automation electric screwdrivers. It is a single tool controller that offers programmable speed, angle, auto reverse and soft start options. The controller provides programmable fastening options for sequence based assembly automation applications. The patented HD-Series hybrid system is the world's first torque control tool using both air and electric power to set and control torque. The HDC precise pneumatic pressure sensor and patented algorithm allow for precision digital torque selection.
-
product
Integrating Sphere
The standard test temperature is 25, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
product
CO2 Concentration Transmitter
H5324
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
1100 HP Water Brake Chassis Dynamometer
TD-24
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred
-
product
Joint Services Electronic Combat Systems Tester
JSECST™
The Joint Services Electronic Combat Systems Tester (JSECST) is part of the family of testers, supporting the U.S. Air Force, Navy, Army, and over 23 allied nation platforms. JSECST performs full end-to-end diagnostic tests of installed systems including radar warning receivers (RWRs), jamming systems, communication systems, and navigation systems. Our JSECST delivers confidence for flight crews and the technicians who support them. It quickly and accurately tests and fault-isolates electronic combat and avionics systems for today's most advanced combat aircraft.
-
product
350W to 1000W - Single Output
CUS350MP Series
*350W (1000W Peak) Convection Cooled*1000W Peak with Forced Air*Medical Certifications (2xMOPP)*Class B Conducted and Radiated EMI*5V 0.3A standby voltage, Remote on/off*Compact size (88 x 183 x 44mm)*Five year warranty
-
product
Full HD Surgical Monitor Series
ASM24FHB
The ASM24FHB Series of medically certified FHD surgical monitors features clear image and accurate color reproduction to fully support medical personnel. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the ASM Series can be easily and quickly cleaned using all common disinfectants and cleaning agents. This ensures a high level of hygiene in pathogen-sensitive environments such as the OR. The ASM Series’ hygienic design also can speed up turnaround time and operating theater preparation.
-
product
Portable Sulphuric Acid Dewpoint Temperature Monitor
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6～50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
-
product
Hot Wire Anemometer
CENTER 332
Air Velocity Measurement: m/s, km/hr, ft/min, MPH, Knots & Build In Temperature ºC / ºF, Humidity %RH, Air Velocity Compensation In Atmospheric Pressure, Air Flow Measure: CMM, CFM, Telescoping Hot Wire Probe
-
product
High-performance multifunctional AC Power Supplies (CV/CF)
PCR-LE Series
The PCR-LE Series is a new line of advanced multifunctional AC power supply that has been developed from our PCR-L/LA Series (linear amplifier type). The PCR-LE Series provides high reliability and can be applied to various applications, by taking advantage of the features that can control broadband waveform freely. Moreover, the PCR-LE Series can be configured as a core device of a test system combined with E-loads and Power Analyzers for “Grid Connection Testing” in regard to dispersed power generation, such as Solar Power, Wind Power, Fuel Cell, and Gas Engine referred to as “New Energy Field”. With various options, the low frequency immunity test and various power enviroment tests are supported. The options for parallel operation and three-phase operation enable you to expand a single-phase system up-to 27kVA, single-phase three wires up-to 54kVA, and a three-phase system up to 81kVA. The system can be applied to a large-scale EMC site for testing of industrial high-capacity air conditioners.
-
product
Flow Sensor For Compressed Air (FLUEREX With Integrated Display)
PF/PFU
This is a flow sensor for compressed air for medium and large flow rates, which is useful for grasping the current state of energy consumption and confirming the effect.
-
product
4U 14-slot Rackmount Chassis
AX6156LE
The AX6156LE is a 4U-high rackmount industrial computer chassis which can hold a 14-slot PCI/ISA backplane and supports ATX Motherboard form factor. One 12cm ball-bearing cooling fan maintains positive air circulation through the whole chassis. The front access I/O ports are designed for ease access and maintenance. Furthermore, this industrial chassis features three 5.25" and one 3.5" disk drive bays. A wide range of standard computing peripherals can be integrated with the chassis to meet different application requirements.
-
product
Scanners
TK94A/TK94RL
The two scanner variations of the type TK94 have similar features. The difference is that variation "A" is used for checking single positions or free space while the version "RL" rotates in both directions without stopping to check for two tools. These scanners are best suited for harsh environments and have a built-in air purge with a strong/fast motor. This scanner would be used in applications that previously used the BK Mikro model 4 or 5 scanners such as lathes, transfer machines or in the work envelope of machining centers.
-
product
Logger version conductivity and temperature sensor
INFINITY-CT A7CT-USB
Infinity-CT is an autonomously deployable data logger for temperature and salinity measurements. The conductivity sensor has a design of 7-electrode. The small-sized instrument (Φ54mm x 255mm, 0.7kg in air) can be deployed and integrated virtually anywhere. The instrument has two depth rating versions: shallow water (200m, A7CT2-USB) and deep water (2,000m, A7CT-USB).
-
product
Vane Probe
AP472S2
Vane probe ∅ 60 mm with handle to measure air speed in the range 0.5…20 m/s.
-
product
Automatic Temperature and Velocity Scanner
ATVS-2020
Advanced Thermal Solutions, Inc.
The only system that can measure both temperatureand air velocity with a single sensor. The system canaccommodate up to 32 channels (sensors) for easy and accuratemapping of the velocity and temperature fields of the testdomain.
-
product
LXI Scalable Matrix Chassis
65-200-001
This LXI scalable matrix chassis offers you a solution that can be easily re-configured by the insertion and removal of up to six LXI matrix plug-in modules (detail in the tables below). It is purchased as an empty chassis with a quantity of plug-in modules required for a particular matrix size. Unused chassis slots are blanked off by the supplied blanking pieces. Cooling is provided by rear fans and front air intakes ensuring no wasted space when the chassis is rack mounted. The cooling system is adaptive to its operating environment to ensure the acoustic noise is minimized when used in quiet laboratory environments and low load conditions.
-
product
Environmental Chamber
REXMED REC-400
MOD. REC-400, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,506 Watts, 11,962 BTU/hr, 3,020 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Intraocular Lens Optical Test System
OptiSpheric® IOL R&D
The OptiSpheric® IOL R&D is specially designed for the analysis of single intraocular lenses in research and development. With the OptiSpheric® IOL R&D, important parameters of all types of lenses (monofocal, multifocal, trifocal, toric, aspheric and those with extended depth of focus (EDOF) – whether diffractive, refractive or sectors) can be measured and tested in air or in situ in accordance with ISO 11979.
-
product
Antennas
Elbit Systems of America’s antenna product line offers ruggedized, field-proven, military communication solutions for air, sea and ground operations. These advanced antennas deliver high performing, continuously connected voice, video, and data communications. Our technologies support high up/down-link rates and make our antennas ideal for fixed and maneuver units. Each system is designed to be fully integrated with most broadband satellite communication systems.
-
product
Co2 Meter Desktop with USB Interface Touch Screen
VAT810-TH/SD (VAT810-CO2)(VAT80
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Desktop:Touch buttons : CO2 monitor Real-time monitoring of indoor air quality including CO2,temperature ,humudity and VOC.
