Linux
open-source operating system first develped by Linus Torvalds.
-
Product
Precision LCR Meter (20Hz to 2MHz)
ST2840
-
ST2840 series pricision LCR meter innovatively adopts a new generation of technologies such as dual CPU architecture, Linux bottom layer, 10.1-inch capacitive touch screen, built-in instruction which effectively solves the defects of slow LCR test, single display and complicated operation in the past.The measurement frequency of ST2840 series is from 20Hz-500kHz/2MHz, which makes up for the shortcoming of lack of high-performance bridge in the frequency range of 500kHz.
-
Product
ARINC 429 Test And Simulation USB Module
USB-429
-
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Extreme Rugged PC/104-Plus Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM2-BT2
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
Evaluation Kit
ROM-DK2620
-
*NXP Arm® Cortex®-A35 i.MX 8ULP Dual up to 1.0 GHz*1 x Arm Cortex-M33 core*Onboard LPDDR4 1GB, 2000MT/s memory*1 x 4 lane MIPI-DSI*1 x USB2.0, 1 x USB 2.0 OTG, 5 x UART, 2 x I2C, 24 x GPIO, 6 x PWM, 1 x CAN*Support Ycoto Linux
-
Product
High Speed Communication Board
MS 1712
-
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
Product
Time Repeater
VCH-402
-
Time repeater VCH-402 is designed for use in TCP/IP networks as a Time Server of the first level (NTP Stratum1).The time repeater is built on the basis of a single-board microcomputer running under the Linux operating system.
-
Product
Ethernet Gateway
-
ICS's Model 9065 Ethernet Gateway is an Ethernet to GPIB Controller that connects easily to your computer's Ethernet port, company network or to the Internet to control GPIB instruments. The Model 9065 is VXI-11 compliant, does not require special drivers and is compatible with the following systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. ICS's 9065 uses VXI-11 RPC calls for secure communication with virtually any computer. Eliminates the need for special drivers. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product.
-
Product
4K Custom Lens USB 3.0 Camera Board (Color)
See3CAM_CU135
-
See3CAM_CU135 is a 13MP fixed focus 4K USB camera board with good low light performance and iHDR support. This 4K board camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows and Linux. This 4K board camera is also backward compatible with USB 2.0 host ports.
-
Product
Modular I/O via Ethernet
2601 Series
-
100/10 Mbps Ethernet gateway to 2600 series I/O modulesFour RS-232/422/485 ports for remote serial devicesIntegral support for interlock and emergency stop circuitsNetwork watchdog shuts off I/O upon client faultHigh-performance network stack: up to 1000 transactions/secondUltra-fast, one second boot-up timeOptically isolated serial communication to I/O modulesWatchdog TimerCE CompliantCompatible with Linux and Windows
-
Product
X.25 Adapters & XOT
FarSync X25 T2Ee
-
The FarSync X25 T2Ee PCIe card provides a very flexible 2 port PCI Express low profile X.25 communications platform for Linux and Windows systems
-
Product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
Software Test Automation Solution
ZAPTEST
-
ZAPTEST is a software test automation solution for testing Mobile; Web; Desktop applications Cross-Platform. ZAPTEST allows testing of any GUI based software on any modern OS, mobile or conventional including iOS; Android; WinMo; Blackberry; Windows; Mac; and Linux, and supports testing of Agile and CI development.
-
Product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Jetson TX2 NX™ Edge AI Inference Platform
DLAP-211-JT2
Platform
- Deep learning acceleration with NVIDIA® Jetson™ TX2 NX- Linux® Ubuntu operating system- Support wide operating temperature- Compact, durable and fanless design for 24/7 operation- Wide variety of industrial I/O ports and visual inferencing capabilities- Available with AWS IoT Greengrass service and Allxon remote device management
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
COM Express Type 6 Basic Module With Intel® Xeon® & 8th Gen Intel® Core™ Processors And Intel® CM246/QM370/HM370
CEM520
-
The CEM520 is a high-performance COM Express Type 6 basic module featuring triple independent displays, industrial operating temperatures and rich expansions. The CEM520 is based on the Intel® Xeon® E-2176M and 8th generation Intel® Core™ i7/i5/i3 processors (codename: Coffee Lake) with the Intel® CM246/QM370/HM370 chipset. The system-on-module is equipped with dual DDR4-2666 SO-DIMM slots for up to 32GB of system memory. Its wide operating temperature range of -40°C to +85°C strengthens the adaptability of harsh operating conditions. Integrated with Intel® Gen 9 graphics, and with the support of DX11/12, OCL 2.0 and OGL 4.3/4.4, the Intel® Xeon® and Core™-based computer-on-module presents excellent graphics performance with a resolution up to 4K. Three independent displays are supported through one LVDS, one VGA and two DDI ports for HDMI, DisplayPort. The CEM520 comes with multiple I/O connectors including four SATA-600 interfaces with RAID 0/1/5/10, one Gigabit LAN port with Intel® i219-LM controller, four USB 3.0 ports, eight USB 2.0 ports, and 4-In/Out DIO port. Also, the system-on-module is expandable with one PCIe x16 slot and eight PCIe x1 slots, as well as LPC and SMB expansion buses. Trusted Platform Module 2.0 (TPM 2.0) is supported to provide efficient hardware-based data protection. This new powerful COM Express Type 6 module is compatible with Windows® 10 and Linux operating systems. It also supports AMS.AXView – Axiomtek’s exclusive software for smart device monitoring and remote management applications.
-
Product
Extreme Rugged PCI-104 Single Board Computer with Intel® Atom™ Processor E3800 Series SOC
CM3-BT1
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
cRIO-9035, 1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, and Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
784774-01
Embedded Controller
1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, and Kintex-7 70T FPGA, 8-Slot CompactRIO Controller - The cRIO-9035 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. Additionally, the cRIO-9035 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
MIL-STD-1553 XMC Interface Module
XMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Ethernet to Modbus RTU Interface
Model 9099
-
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
Product
Imaging Modules
-
Teledyne e2v has developed compact MIPI modules which feature our own high performance CMOS image sensors inside a pre-focused, industrial-grade scanning optic. As a turnkey sensor/optics for imaging systems, these modules offers customers significant reduction in development time and cost savings. Only a few screws are needed to mount the module, with simple connection to the image processing system through an FPC cable connector. Software development efforts can also be reduced by using some limited API-layer Linux software drivers. This enables the module to be seamlessly interfaced to popular ISP platforms.
-
Product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
UI Test Tool for Web, Java, Windows, Android & iOS
QF-Test
-
QF-Test is the established tool for professional GUI test automation of desktop, web & mobile applications as well as PDF documents. QF-Test is a low-code GUI test tool that allows you to efficiently create test cases, e.g. using Capture/Replay, without any programming knowledge across platforms on Windows, Linux and macOS. For software developers, Jython, Groovy or JavaScript offer advanced scripting possibilities. Tests can be run automatically via continuous integration tools such as Jenkins and generate detailed log files and XML or HTML reports. Use QF-Test to create robust and stable regression tests for various GUI technologies. QF-Test supports all types of Java GUIs, ranging from Swing (including ULC, JIDE components, CaptainCasa), its successor JavaFX, as well as the Standard Widget Toolkit (SWT) and Eclipse, including plugins and RCP applications. You can also use QF-Test to test dynamic web applications based on Angular, React or Vue.js, for example, including Electron and hybrid applications using JxBrowser, JPro or WebSwing, for example. QF-Test supports native Windows desktop applications created with Win32, .Net, Windows Forms, WPF, Windows Apps. Mobile applications can be tested on real devices or with the Android Studio Emulator or iOS Simulator and Xcode.In addition, you can test automated whether your web application complies with common accessibility standards in just a few simple steps. PDF documents can also be conveniently tested automatically with QF-Test. On the market since 2001, the test tool is continuously being actively developed and is currently used by more than 1,500 companies across 60 countries. Contact us by e-mail at service@qftest.com or get a free trial version at www.qftest.com/en!
-
Product
Ethernet to GPIB Controller
Model 9065
-
* Controls GPIB Devices anywhere there is a network or internet connection.* No special driver required which eliminates driver problems. * Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Fully VXI-11 compliant. * Includes ICS's VXI-11 and VISA keyboard control programs. Control instruments without a program. * Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver lets you change network settings from any browser.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the GPIB instruments.* Supports GPIB and HP-IB 488.2 complicant instruments.* 9065 is a 2nd generation drop-in replacement for ICS's Model 8065. The Model 9065 is 2x to 4x faster and includes a webserver instrument control page.
-
Product
Shared Memory Network PCI Express Interface
PCIe-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodesNetwork interrupts supported - PCIe 2.0 (x4) CompliantSoftware Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
FlexMAX 3U
-
The FlexMAX 3U is a high performance, modular multi-protocol intelligent platform that offers support for large quantities of various I/O types. Powered by Linux Real Time, the FlexMAX 3U is designed to receive and transmit data across dozens or hundreds of channels with a high time and sync precision, bridge data from receive to transmit channels, detect or inject errors and comes with data filtering and triggering capabilities.
-
Product
12DI/12DO Intelligent I/O Gateway
ADAM-6750
-
Linux Open Platform12ch digital input(counter)/12ch digital output(pulse output)Programming: linux C API, Node-RED (graphic programming environment)Cloud/Database access ,edge data analysis and logic control, data visualization by dashboardInterfaces: RS-485x2, Ethernet port x 2 ,1 x USB Type-A 2.0, 1 x USB Micro-B 2.0
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARM LPC3250 Board
MS 1509
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
Software
ATS-SDK
-
ATS-SDK is a Windows and Linux compatible software development kit created by AlazarTech to allow users to programmatically control and acquire data from its line of waveform digitizers. With full support for C/C++ and C# (Visual Studio or GCC), MATLAB, LabVIEW and Python environments, ATS-SDK is the most powerful, efficient and high-performance programming environment. ATS-SDK includes many example programs that can be used as a starting point for custom code development for specific applications. As of version 7.1, ATS-SDK replaces ATS-VI as the recommended programming environment for LabVIEW users.
