Electrostatic Discharge Simulators
create known values of electrostatic discharge.
-
Product
PCB Simulation Solutions for High-Performance Designs
HyperLynx
-
HyperLynx® offers a complete suite of analysis and verification software that meets the needs of PCB engineers at any point in the board design flow. Easy to use and integrate into your flow, HyperLynx equips PCB engineers to efficiently analyze, solve and verify critical requirements to avoid costly re-spins. Achieve greater innovation, faster time-to-market and decreased costs with HyperLynx.
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Modules For PMC
AMCX1553
-
MIL-STD-1553 Test and Simulation modules for PMC with 1, 2 or 4 dual redundant channels plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
-
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Product
MIMIC® Wireless Simulator
-
Mobile device and network complexity is continuously increasing due to the multitude of devices, technologies and traffic patterns. As a result, wireless equipment manufacturers must test their products from every different aspect. They need to do this to improve quality and reduce costs.
-
Product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
-
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
-
Product
Multi-Domain Simulation
-
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
Product
Portable Solar Simulator
XES-40S3
-
We have manufactured the highly accurate solar simulators, which is used for evaluations where sunlight needs to be recreated. By fully utilizing these technologies, we have developed this portable Solar Simulator, which can easily reproduces sunlight. Our device is optimum solution for initial evaluations and inspections for the research purpose.
-
Product
Simulators (Gen II)
J1939
-
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
Environmental Simulation
-
Is your product heat-resistant? Throughout their useful lives, technical products are subject to a multitude of environmental influences, e.g., heat, cold, oscillations or impacts. This influences their functioning and length of service life. We can find out how the effect and cause are interrelated with an environmental simulation. We will test your products under specific environmental conditions and help you to optimize them for sustainable product development.
-
Product
T400 Radar Emulation Simulator
-
Kratos Defense & Security Solutions, Inc.
The Radar Emulation Simulator provides a cost-effective solution for simulating targets and channel effects in an RF environment. The system can be controlled via a standalone graphical user interface for simplified scenario applications, a dedicated real-time interface, or remotely via the Ethernet interface.
-
Product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
-
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 750 V Isolation
43-752A-001
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Accelerometer Simulator
MTN/8302
-
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
Product
Model Based Design and Simulation
-
Requirements validation through simulation and autogeneration of embedded systems
-
Product
Uphole Simulator
-
For testing Boom Boxes and other Blasters. The Uphole Simulator is the tool for testing a dynamite blaster in the shop or field. Quick and easy, the UHS unit connects to the high voltage output of the blaster and the uphole geophone input.The UHS sinks the output voltage from the blaster. As it receives the charge, it counts down 30 milliseconds and then outputs a waveform, simulating the signal the blaster might receive from an actual geophone.
-
Product
Dynamic Test Board Vehicle Simulator
DTB
-
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
Product
Single Long Pulse Solar Simulator & I-V Test System
TriSOL SLPSS
-
The OAI Test System for HIGH EFFICIENCY SOLAR CELLS overcomes the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match the cell’s dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell efficiency leading to increased profitability.
-
Product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
-
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
Product
MIMIC® Server Simulator
-
How do you test your management application's scalability to support thousands of servers and devices?How do you test whether a load balancer can handle a Web Server farm without reaching the performance limits?
-
Product
Solar Array IV Curve Simulation Softpanel
-
Chroma Systems Solutions, Inc.
Easily program the I-V curve of the Solar Array Simulator with this test software as well as the I-V and P-V curves for real-time testing. See both dynamic and static MPPT efficiency and even simulate the IV Curve with shadows. The real world weather simulation function allows the user to simulate the irradiation intensity and temperature level from early morning to nightfall.
-
Product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
Product
Multi-channel GPS Signal Simulator
MP6220
-
*Up to 8 channels support positioning test*Can also be used as a single channel
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
PXI Switching, Simulation & Instrumentation for virtually every application that can be tested
-
We are a leading manufacturer of PXI switch, simulation and instrumentation modules, available in PXI & PXIe formats.
-
Product
PXI Millivolt Thermocouple Simulator Module - 24 Channel
41-760-002
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
Electromagnetic Simulation Software Suite
EMTOOLS
-
EMTOOLS is a computational electromagnetic (CEM) software suite comprised of 16 different software codes. ACAL (Advanced Complex Algebra Library) is an out-of-core linear system solution library, using a hyper-matrix approach to partition the problem. The AntFarm™ (Antenna Farm) toolkit analyzes the radiation and electromagnetic interference (EMI) effects of single or multiple heterogeneous RF systems. Apatch™ software is an antenna design and analysis tool that provides antenna simulation and modeling by computing the radiation and receiving pattern of an antenna or antenna array installed in an operational environment...
-
Product
Radio Link Simulator
RLS-2100
-
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
Product
Environmental Shock Simulation Machine For Drop Testing
-
# Simulates environmental handling threats small handheld products must survive.# Gauges your product?s ability to survive handling environments.# Controls key test variables: product orientation at impact; nature of the impact surface.# Maintains orientation to just prior to impact then releases for unrestrained impact.# llows user changeable impact surfaces to better simulate the handing environment.# Includes 4 ch short transient shock instrumentation system.
-
Product
PXI/PXIe LVDT, RVDT, Resolver Simulator Modules
-
Linear variable differential transformers (LVDT) are electrical transformer sensors to measure linear displacement. Driven by an AC excitation source, the LVDT generates a pair of AC output signals modulated according to the core's mechanical position (displacement). LVDTs have been widely used in applications such as power turbines, hydraulics, automation, aircraft, satellites, nuclear reactors, and many others. These transducers have low hysteresis and excellent repeatability.
-
Product
2 PRI + 24 BRI-S/T ISDN Simulator
CH-24BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 24 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
