PCIe
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller.
See Also: PCI Express, Instrument Control Buses, Modular Instruments, PCI Express Test, PCI Express Analyzers, PCI, Compute Express Link
-
Product
Opto Serial Module
DS-MPE-SER4OPT
-
The DS-MPE-SER4OPT offers 4 RS-232/RS-485 opto-isolated serial ports in a PCIe MiniCard form factor. Each port offers 16C550 compatibility and ultra-deep 256-byte TX/RX FIFOs. Maximum data rates are 1Mbps in RS-232 mode and 10Mbps in RS-485 mode. The board is available preconfigured for 4 RS-232 ports, 4 RS-485 ports, or a combination of 2 RS-232 and 2 RS-485 ports. I/O signals are provided on two miniature latching connectors, with 2 ports per connector.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5916-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
Multifunction I/O
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
PCIe
SFF 8639 Gen4 (U.2)
-
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
Product
PCIe-6363, PCI Express, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device
781051-01
Multifunction I/O
PCI Express, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device - The PCIe‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6363 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ ATX Server Board with 4 DDR4, 7 PCIe, 6 USB 3.1, 8 SATA3, Quad/Dual LANs, IPMI
ASMB-786
-
- LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ i7/i5/i3 processors with C246 chipset- DDR4 2666/2400/2133 MHz ECC/Non-ECC UDIMM up to 128 GB- One Gen 3.0 PCIe x16 link (or two PCIe x16 slots with x8 link), two PCIe x4, and three PCIe x1 slots- Triple displays - DVI-D, VGA and HDMI 2.0 ports- Eight SATA3 ports and six USB 3.1 ports- Rackmount optimized placement with positive air flow design- 0 ~ 60° C ambient operating temperature range
-
Product
2-Channel 200 MHz A/D with 766 DDCs, Kintex UltraScale FPGA - 3U VPX
Model 52865
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete software radio receiver solution for extremely high-channel-count applications- Uses Xilinx Kintex UltraScale KU035 FPGAs- Two 200 MHz 16-bit A/Ds- Four wideband DDCs (digital downconverters)- Up to 762 narrowband DDCs- Sample clock generation and synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x4- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Rugged Analog I/O Modules
-
Our extensive line of analog I/O modules currently includes PC/104, PCIe MiniCard and FeaturePak form-factor products, providing both A/D and D/A functions. Most of these products also include digital I/O and counter/timer features. A unique feature of Diamond analog I/O modules is our patented autocalibration technology, which can reduce analog measurement errors by up to 10 times relative to conventional designs.
-
Product
5-Port PCI Express
PEX 8747
-
The ExpressLane™ PEX 8747 is a 48-lane, 5-port, PCIe Gen 3 switch device developed on 40nm technology. The PEX 8747 device offers Multi-Host PCI Express switching capability enabling users to connect a host to its respective endpoints via scalable, high bandwidth, non-blocking interconnection to a variety of graphics applications. The PEX 8747 is optimized to support high-resolution graphics while supporting peer-to-peer traffic and multicast for maximum performance.
-
Product
ATCA Rear Transition Module
ART103
-
The ART103 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC103 carrier board. The ART103 is a passive RTM that allows for the additional connectivity of two GbE ports, Management 10/100Mbit Ethernet, Management RS-232 serial interface and three PCIe x4 lanes for expansion. One of the PMC J4s (user defined I/O) is routed to the back.
-
Product
ATCA Rear Transition Module
ART108
-
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
Product
Multi-standard Cable/terrestrial Modulator For PCIe
DTA-2111
-
DekTec's PCIe modulator for most QAM-, OFDM- and VSB-based modulation standards. The DTA-2111 has a programmable output level with excellent signal quality due to digital upconversion.
-
Product
Ultra Compact Industrial Computers, mini PCIe socket for WIFI / 4G module
Neousys NRU
-
Ultra-compact industrial computers based on NVIDIA® Jetson AGX Xavier ™ for mobile use (in transport, in surveillance systems, in industrial systems).- NVIDIA® Jetson AGX Xavier ™ SOM with JetPack 4.4- IEEE 802.3at Gigabit PoE + or 0GBASE-T 10G ports - M.2 2280 M key socket for NVMe SSD- mini PCIe socket for WIFI / 4G module - GPS PPS input
-
Product
PCIe High-Speed Digitizer
U5310A
-
The U5310A is a two channel PCIe, DC coupled 10-bit signal acquisition card providing sample rates up to 10 GS/s with 2.5 GHz bandwidth for use in a variety of advanced imaging and processing systems. Featuring unique spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) performances in high frequencies, especially at 250 mV full scale range (FSR), the U5310A ADC card is suited for embedded OEM applications requiring signal acquisition at wide bandwidth and high dynamic range.
-
Product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB116
-
The FAB116 features a PICMG 1.3 CPU card slot, one PCIe x16 slot, three PCIe x4 slots, three PCI, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB116 is compatible with Axiomtek's AX60551 and AX60552 chassis.
-
Product
DAQ Cards
-
DAQ cards are high-speed yet cost-saving products, including PCI DAQ and PCIe DAQ that feature multifunction I/O selections such as analog I/O.
-
Product
Single-Port 50GbE PCIe Ethernet NIC
P150P
-
Based on Broadcom’s scalable 10/25/50/100/200G Ethernet controller architecture, the NetXtreme®-E Series P150P 1x50G PCIe NIC is designed to build highly scalable, feature-rich networking solutions in servers for enterprise and cloud-scale networking and storage applications, including high-performance computing, telco, machine learning, storage disaggregation and data analytics.
-
Product
HPx-400e PCIe Radar Input Card
-
The HPx-400e is a high-performance PCI express single or dual stream primary radar acquisition card, capable of capturing and processing analogue and digital primary radar video from up to two independent radars. The dual stream HPx-400e variant supports a number of multi-channel input modes, including dual redundancy and fully independent dual-stream capture.
-
Product
14 Bit Digitizer For PCIe With 8 Channels 65 MS/s Up To 8 GS Memory
Octopus-14 Express / CompuScope Express 8385
-
The GaGe Octopus Express 83XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11-bits with 10 MHz input.
-
Product
9/12-Slot All-Hybrid 3U PXIe Chassis, ATX-Powered With 16 GB/s System Bandwidth Capability
PXES-2596
-
The ADLINK PXES-2596 is a 9-slot PXI Express all-hybrid chassis. It features 1 system slot and 8 hybrid slots, supporting CompactPCI, PXI, and PXI Express modules for maximum flexibility. Built on a two-link PXI Express architecture with 16GB/s system bandwidth, all peripheral slots support PCIe Gen3 x4, providing up to 4GB/s per slot.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-5V-I
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
Product
PCIe Mini Module
PCIe-Mini-DIO16/32
-
The PCIe-Mini-DIO16/32 has 32 I/O channels that can monitor or control the on/off (high/low) status of up to 16 differential devices or up to 32 channels LVTTL, software selectable in groups of 2. Each channel can be used as an input or output.
-
Product
Embedded MXM GPU Module with Embedded NVIDIA RTX™ A500
EGX-MXM-A500
Graphics Card
- NVIDIA Ampere Architecture- Standard MXM 3.1 Type A (82 x 70 mm)- PCIe Gen 4 x4 interface- 2048 CUDA® cores, 16 RT Cores, and 64 Tensor Cores- 6.54 TFLOPS Peak FP32 performance
-
Product
Power Supplies
RM - SERIES
-
With dual PCI-E connectors, the RM Series carries all its essentials to power your system. Enjoy the graphic rendered programs and games without the threat of overheating. Its dark aluminum chassis not only looks good, but dramatically relieves heat built-up. The 120mm cooling fan enhances the already efficient heat dissipation rate and helps balance the cooling system with noise level. The RM Series is great for high end users to everyday casual users. Whatever your system needs, the RM Series can deliver.
-
Product
2200-Channel GSM Channelizer wih Quad A/D - 6U VPX
Model 58663
-
- Complete GSM channelizer with analog IF interface- Eight 180 MHz 16-bit A/Ds- Four banks of 375 DDCs for upper GSM band- Four banks of 175 DDCs for lower GSM band- PCI Express (Gen. 1 & 2) interface up to x4- LVPECL clock/sync bus for multiboard synchronization- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Circuit Module, Riser for ISMB,PCIex4+2 PCIex1+PCIex16 A101-1,Ro
AIMB-R431F-21A1E
-
- Connecting Interface: PCIe x16 + PCIe x4- Expansion Slots: 1 PCIe x16 + 2 PCIe x1
-
Product
JadeFX FlexorSet 2-Ch. 3.0 GHz A/D, 2-Ch. 2.8 GHz D/A - 3U VPX
Model 5983-320
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex UltraScale FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two 3.0 GHz*A/Ds- Two 2.8 GHz* D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and synchronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Xilinx Sublicense FAQs - Pentek Sublicensing Agreement for Xilinx JESD204 IP Cores- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
PCIe-8371, x4 Gen1 PCI Express Host, 832 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
779723-01
Remote Control Interface
The PCIe‑8371 is an MXI‑Express remote controller for devices or systems cabled over PCI from a computer with a PCI Express slot. The PCIe‑8371 remote controller provides a x4 PCI Express link over a copper cable to the PXIe‑8370 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
Micro-ATX Motherboard AMD Ryzen™ Embedded 7000 Series Processors
AIMB-523
-
AMD Ryzen™ Embedded 7000 Series processors with B650 chipset6 LAN ports with 2.5GbE for multiple IP-based devicesTriple displays by 1 DP and 2 HDMIHigh-speed expansions: PCIex16 Gen5, 8 USB 3.2, 1 M.2 M-key (PCIe Gen4 x4)1 internal USB2.0 type A to support USB keylock functionsWindows 10/11
-
Product
PCIe-7852, Virtex-5 LX50 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781103-01
Multifunction Reconfigurable I/O
Virtex-5 LX50 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7852 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7852 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
