PCIe
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller.
See Also: PCI Express, Instrument Control Buses, Modular Instruments, PCI Express Test, PCI Express Analyzers, PCI, Compute Express Link
-
Product
Opto Serial Module
DS-MPE-SER4OPT
-
The DS-MPE-SER4OPT offers 4 RS-232/RS-485 opto-isolated serial ports in a PCIe MiniCard form factor. Each port offers 16C550 compatibility and ultra-deep 256-byte TX/RX FIFOs. Maximum data rates are 1Mbps in RS-232 mode and 10Mbps in RS-485 mode. The board is available preconfigured for 4 RS-232 ports, 4 RS-485 ports, or a combination of 2 RS-232 and 2 RS-485 ports. I/O signals are provided on two miniature latching connectors, with 2 ports per connector.
-
Product
SMARC
ROM-5780 B1
-
Advantech ROM-5780 B1 SMARC 2.1 Computer-on-Module is powered by Rockchip RK3399 SOC which includes dual-core Arm Cortex-A72 and quad-core Arm Cortex-A53 processors and Arm Mali-T860MP4 3D graphics engine. It provides rich display interface: HDMI 4K@60Hz, eDP and LVDS to meet different requirement. It also features USB3.0, PCIe 2.0, SATA, Gigabit Ethernet, MIPI-CSI for embedded applications. It is the ideal solution for POS, vending, infotainment, Medical.
-
Product
PCI Express Optical Link Board
SIS1100-E2
-
The SIS1100-e2 is the follow up card to our SIS1100-eCMC board (without CMC carrier functionality). It was developed to extend the lify cycle of our PCIe to VME interface. For software/driver compatibility reasons we still employ the PEX8311 PCI Express to local bus bridge chip.
-
Product
GigE And 3x ASI Ports For PCIe
DTA-2160
-
DekTec's Gigabit Ethernet adapter with three ASI/SDI ports, allowing zero-jitter transmission and reception of Transport Streams over IP networks; the additional three ASI ports allow easy conversion between the two interface types.
-
Product
PCIe Direct Digital Synthesizer
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.
-
Product
PCIe Thunderbolt 3 EON Express 12-Bit Digitizers
Thunderbolt 3
Digitizer
Thunderbolt 3 provides the largest bit-rate capacity interface possible at up to 40 Gbps (5 GB/s) over a USB-C connector to support a variety of protocols including PCI Express (PCIe).
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels
M2P.6566-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2230-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCI Express Card With Eight Isolated Inputs, Eight Relay Outputs, And Change Of State Detection
PCIe-IIRO-8
-
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
Product
PCI Express To PCI Express Expansion For Multiple Host Computers
ExpressBox16-SX8
-
Magma’s ExpressBox 16 is the simplest solution to seamlessly increase the number of PCI Express® slots available to your server or workstation. ExpressBox 16 expands one host PCIe® slot to sixteen slots by extending PCI Express signals over a high-bandwidth x8 or x16 connection to an external Magma enclosure.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Power Supplies
NW-550B
-
Experience our new NW-series of power supplies. The NW-series can power your system from 450 to 650 watts. It offers a cooling system with a fan size of 120mm with automatic settings, so you no longer have to worry about high or low settings and if your fan is spinning too slow or too fast. The NW-series will adjust itself according to the necessary heat dissipation level. It is dual PCI-E ready for better graphics capabilities (at 650W). Painted in black, the NW series works and looks great.
-
Product
cPCI Serial Chassis 9 Slots
4U 50HP
Chassis
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 9 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 9 slot PCIe Gen3 backplane with single star topology, powered by a 300W cPCI Serial power supply.
-
Product
COM Express Rev. 3.1 Basic Size Type 7 Module with AMD Embedded Ryzen™ V3000
Express-VR7
Computer on Module
ADLINK’s Express-VR7 COM Express Type 7 Basic size module is based on AMD Embedded Ryzen™ V3000 series processor. Offering up to 8 cores and 16 threads at 15W/45W TDP, the module exhibits the best performance per watt in its class, along with 14x PCIe Gen4 lanes with enterprise level reliability and extreme rugged temperature option (-40°C to 85°C).
-
Product
MiniPCI Express to M.2 PCIe Adapter (B-key)
SKU-089-12
-
MiniPCI Express Adapter has M.2 (B-key) connector. It allows connection M.2 modules with B-key to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits, and this Adapter supports PCI express, SIM and USB 2.0 interfaces.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52741
-
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Adaptive Relay Board, Virtex-6 FPGA - PCIe
Model 78624
-
Model 78624 is a member of the Cobalt® family of high-performance PCI Express boards based on the Xilinx Virtex-6 FPGA. As an IF relay, it accepts two IF analog input channels, modifies up to 34 signals, and thendelivers them to two analog IF outputs. Any signal within each IF band can be independently enabled or disabled, and changed in both frequency and amplitude as it passes through the module. The 78624 supports many useful functions for both commercial and military communications systems including signal drop/add/replace, frequency shifting and hopping, amplitude equalization, and bandwidth consolidation. Applications include countermeasures, active tracking and monitoring, channel security, interception, adaptive spectral management, jamming, and encryption.
-
Product
3U PCIe Gen2 ATR Style Chassis
Crosswind 600
-
PCI-Systems innovative 1-2-3 system. 1: Lab unit 2: Configure unit 3: Deploy unit! All our chassis and prototype systems can be deployed without needing to change out the chassis. Add Front and rear custom covers and full sealing and you are ready to go to qualification!
-
Product
Industrial ATX Motherboard with 8th/9th Gen Intel® Core™ i9/i7/i5/i3 or Xeon® E Processors
IMB-M45
Motherboard
ADLINK IMB-M45 ATX industrial motherboard supports the 8th/9th Generation Intel Core i9/i7/i5/i3 and Xeon E3 processor in the LGA1151 package, and the Intel C246 chipset. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz ECC or non-ECC memory up to 128 GB in four DIMM slots.
-
Product
PCIe Compliance Testing
-
Teledyne LeCroy offers an integrated and automated compliance testing system, approved by the PCI-SIG as a standard tool for Link and Transaction Layer Compliance testing for developers working with the PCIe 4.0 and PCIe 5.0 specification. This solution combines a Summit Z58 or Summit Z516 Exerciser and a PCI Express Test Platform (for testing End-Point devices) This system has been selected by the PCI-SIG as a standard test tool for PCI Express 4.0 and PCI Express 5.0 Link and Transaction Layer Compliance Testing.
-
Product
Carrier with System Management
EnsembleSeries™ CCM3011
-
*OpenVPX carrier module designed to use the Data Plane*PCI/PCI-X interface at up tof 133 MHz on each site*x8, x4 and x1 PCIe interfaces*Advanced OpenVPX system management functionality enables remote monitoring, alarm management, and hardware revision and health management*Conduction-cooled and air-cooled variants available
-
Product
24 Port PCI Express
PEX 8625
-
The ExpressLane™ PEX 8625 offers 24 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 24 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. With 24-ports, the PEX 8625 is the largest PCIe switch in the industry serving the communications and networking markets. The PEX 8625 architecture implements Multicast as defined in the PCI Express Specification.
-
Product
14-Bit Digitizer For PCIe Gen-2, 4 Channels 25 MS/s Up To 8 GS Memory
Octave-14 Express / CompuScope 8342
-
The GaGe Octave Express 83XX CompuScope PCIe digitizer card features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11.1-bits with 10 MHz input. Onboard digitizer sample memory is expandable up to 8 GS (16 GB) and up to 8 Octave Express digitizers can be combined for up to 32 channels in a single system.
-
Product
Thin Mini-ITX SBC With Intel® Celeron® Processor N3350, Dual HDMI, LVDS, USB 3.0, PCI Express Mini Card, MSATA And HD Audio
MANO311
-
The MANO311 is powered by the Intel® Celeron® processor N3350 (codename: Apollo Lake). Its customizable I/O interfaces, wide voltage and stunning graphics performance were designed to reduce time-to-market and facilitate quick deployment. The feature-rich MANO311 is an ideal solution for healthcare, automation, retail, digital signage and other Industrial IoT-related applications. The Intel® Atom®-based MANO311 has one 204-pin DDR3L-1867 SO-DIMM socket with up to 8GB of system memory; moreover, it supports 4GB memory down for options. It features one SATA-600 connector, one mSATA socket and one SDXC slot for storage devices. A wide range DC input of 12V to 24V makes the power input selection more flexible for a various applications. Furthermore, the newest mini-ITX motherboard features one PCIe x1 slot and one PCI Express Mini Card slot to enhance its expansion. Triple-display capability is available through the dual HDMI and LVDS.
-
Product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
Model 5973-313
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 250 MHz 16-bit A/Ds- Four multiband DDCs- One digital upconverter- Two 800 MHz 16-bit D/As- Extended Interpolation- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- See comparable JadeFX Xilinx Kintex UltraScale FPGA Family:- Model 5983 JadeFX Kintex UltraScale Processor and FMC Carrier 3U VPX- Model 5983-313 JadeFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
-
Product
Power Supplies
CT Series
-
The CT series has a dual smart fan system that provides the fastest cooling system while maintaining a low noise level. The fans are installed in the front and rear of the power supply for maximum cooling efficiency. The CT series have all the necessary connectors to power all your devices and components. And it is PCI-E ready.
-
Product
3U VPX Extender PCIe Gen3
-
The VPX extender modules are built to extend a 3U or 6U VPX module completely out of a chassis, providing access to all sides of the module for testing and debugging.
-
Product
Fanless Embedded System With LGA1151 Intel® Xeon®, 9th/8th Gen Intel® Core™ I7/i5/i3 Or Celeron® Processor, Intel® C246, ECC/Non-ECC And 1 PCIe X4 Expansion Slot
eBOX710-521-FL
-
*Intel® Xeon®, 9th/8th gen Intel® Core™ i7/i5/i3 or Celeron®processor*2 DDR4 ECC/non-ECC memory supported, up to 64GB*Dual swappable 2.5" SATA HDD drive bays with RAID 0 &1*DVI-I, HDMI, and DisplayPort with triple-view supported*6 GbE LAN, 6 USB 3.2 and 1 PCIe x4 expansion slot*Flexible I/O window supported
-
Product
2-slot Fanless Industrial System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170, Front-access I/O, PCIe And PCI Slots
IPC962-512-FL
-
The IPC962-512-FL is powered by the 7th/6th generation Intel® Core™ and Celeron® processors (codename: Kaby Lake/Skylake) with the Intel® Q170 chipset. It is equipped with dual DDR4-2133 SO-DIMM slots with up to 32GB system memory. The ultra-compact industrial computer supports two swappable 2.5" HDDs; moreover, it offers flexible expansion options with one I/O module slot and two PCI/PCIe slots. It also has a wide operating temperature range of -10°C to +60°C and a 24VDC (uMin=19V / uMax=30V) power input for severe environments. According to the features above, this rugged IP40 industrial PC is a great choice for a wide variety of Industrial IoT applications including automatic optical inspection, digital signage, motion control, and factory automation.
-
Product
Ethernet Network Adapters
-
Available in PCIe NIC and OCP mezzanine 2.0 and 3.0 form factors, Broadcom’s Ethernet network adapters support configurations ranging from 1G to 200G, and utilizing both optical and copper connectivity.
