Three Phase
Three voltage waveforms at 120°,1/3 of a cycle offset in time.
-
Product
Metra Power Clamp
1000A
-
Metra Power Clamp 1000A/400A measures, calculate and displays important electrical pa-rameters of single phase or three phase power system. It also features Resistance, continuity, diode and non contact voltage detection.
-
Product
Three-Phase AC Power Source 320 Vrms, 3 KVA, 550 Hz
AC6903L
-
Keysight’s AC6900 Series three-phase power source provides a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
Product
AC-Powered, Phase Sequence Monitor
PAA/PLA
Phase Sequence Monitor
NAI's PAA and PLA are AC-Powered, Phase Sequence Monitors that protect three-phase loads from damage due to phase reversals or phase absence. These sequence monitors are ideally suited for rugged defense and industrial applications.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
Phase Noise Analyzer
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
AC-DC Power Supply Solutions
-
Advanced Conversion Technology, Inc
From single to three phase inputs, 60 Hz or 400 Hz, ACT can provide you with a design to meet your demanding applications. ACT can also provide designs that incorporate an active PFC front end, single and three phase, which provides less than 3% total current harmonic distortion.
-
Product
DC-Powered, Phase Sequence Monitor
PAD/PLD
Phase Sequence Monitor
NAI's PAD and PLD are DC-Powered, Phase Sequence Monitors that protect three-phase loads from damage due to phase reversals or phase absence. These sequence monitors are ideally suited for rugged defense and industrial applications.
-
Product
Phase Angle Voltmeter, Industry Standard
2250A
Phase Angle Voltmeter
NAI's 2250A Phase Angle Voltmeter is the most accurate and versatile AC measurement tool in the Synchro/Resolver and LVDT/RVDT marketplace. Considered the industry standard and based on the latest DSP and FPGA technologies, the 2250A substantially extends and simplifies the capabilities of the legacy 2250 model.
-
Product
Three-Phase Relay Test Equipment
AK-10
-
The new AK-10 three-phase relay test equipment from Amperis features AC and DC Voltage Source ; AC Current Source ; AC/DC Auxiliary Power Source ; 8 possible configurations.
-
Product
Three Phase Power Calibrators And Tester Of Power Engineering Devices
C300B
-
Calmet Smart Calibration Devices
Three phase, class 0.02 and 0.05 power quality calibrator up to 120A (360A) and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
-
Product
DC POWER
VARIABLE TRANSFORMER
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
Product
Grid Simulator
PAS-F
-
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
Product
Phase Noise Test System
N5511A
Phase Noise Analyzer
The Keysight N5511A phase noise test system (PNTS) lets you measure at the limits of physics with readings down to kT (-177 dBm/Hz). The N5511A PNTS is a replacement for the gold-standard Keysight E5500 phase noise measurement system and is designed to meet the needs of phase noise power users.
-
Product
Phase Noise Analyzer and VCO Tester
FSPN
Phase Noise Analyzer
The R&S®FSPN phase noise analyzer and VCO tester is designed to provide both very high sensitivity and measurement speed for production and design engineers working in these fields characterizing sources such as synthesizers, VCOs, OCXOs, and DROs. It is the ideal instrument for demanding development and production phase noise and VCO analysis.
-
Product
Phase Testers
-
Measurement on the voltage detection terminal and covered wireSafely used even for high-voltage bare wiresConsisting of the transmission and reception parts as well as the optical fiber wire connection those two parts
-
Product
Phase Shifter
-
A microwave network module which provides a controllable phase shift of the RF signal.
-
Product
Phase Detectors
-
High DC output versus phaseLow DC offsetRugged metal coaxial packageTiny surface mount packages, 0.38 x 0.50 x .023 in.
-
Product
Three Axis Accelerometers
TAA
-
The Inertial Labs MEMS TAA-308, TAA-315 and TAA-340 are the third generation of the Inertial Labs MEMS, three-axis high-precision accelerometers released in a stand-alone design. The TAA-308, TAA-315 and TAA-340 are revolutionary, compact, self-contained, strapdown, Navigation-grade Accelerometers that measure linear accelerations with high precision due to their unique design and developed by Inertial Labs over last 20 years several significant know-know and technics in calibrations of inertial sensors. Measured by TAA Accelerometers accelerations are determined with low noise and very good repeatability for both motionless and dynamic applications.
-
Product
Phase Detectors
CD series
-
The CD series is a phase detector module. It is possible to detect small level signal and signal buried in noise.
-
Product
Phasing Sticks
-
High voltage phasing rods enable phase comparisons to be made at the point of paralleling two circuits without the interposition of voltage transformers or secondary wiring circuits.
-
Product
Three Axis Helmholtz Coil Systems
-
Macintyre Electronic Design Associa
he MEDA turnkey closed loop magnetic field sources cancel the local ambient field as well as generate accurate and uniform magnetic fields in a control volume. The sources use Helmholtz coils driven by control currents to produce stable magnetic fields from 1 nT to 100,000 nT. The accuracy of the field in the control volume is better than 0.05% of the setting.
-
Product
Phase Locked Oscillators
-
Phase locked oscillators (PLO) utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals at lower frequencies. Frequency multipliers, amplifiers and filters are used to extend the low frequencies for higher frequency requirements. The standard offering covers the frequency range of 2 to 110 GHz and provides both internal and external reference options. The frequency stability and phase noise are dependent on the oscillator reference type.
-
Product
Phase Detector
Paula
-
BAUR paula phase detector. The paula phase detector is used for clear phase identification in earthed and shorted medium and high-voltage cables. With the help of the measurement procedure tried and tested over many years, paula delivers precise phase allocation without scope for interpretation and corresponds to the highest safety standards for tasks on and close to electric equipment.* Clear phase determination possible in cable lengths up to 40 km* Highest level of safety when used on earthed and shorted cables in compliance with EN 50110-1 (DIN VDE 0105-100)* Suitable for all switchgear constructions due to compact design of the signal injectors* Ready for operation for up to 2 weeks (standby mode)
-
Product
Phase Angle Meters
GF211
-
Beijing GFUVE Electronics Co.,Ltd.
It can be applied to electric power dispatching center, relay protection department or relay protection in power plant. Its metric division class makes it suitable for petroleum, railways and the iron and steel industries also.
-
Product
Phase Sequence Tester
TKF-12
-
The TKF-12 tester is a modern high-quality, simple and safe device. However it is recommended to get acquainted with he present manual in order to avoid measuring errors and prevent possible problems related to operation of the meter.
-
Product
Phase Rotation & Continuity
PC15250
-
Quickly and simply prove continuity of all 3 lines. Identifies which are faulty and shows the sequence of phase rotation. Fast & effective method of identifying worn or unmarked cables, and ensuring 3-phase outlets and machinery are wired correctly.
-
-
Product
Phase Shifters
-
Low insertion lossPhase shift adjustable up to 360°Surface mount packages as small as 0.80x.045x0.25 in.
-
Product
Phase Shifting Transformer
-
Supreme Instrument Laboratories
Supreme make PHASE SHIFTING TRANSFORMERS are special transformers which provide convenient means to adjust phase angle (power factor) of A.C. loading circuit while testing power factor sensitive device for the full 90 degree LAG through '0' degree to 90 degree LEAD. Based on their rating these Phase shifters are manufactured in two configuration.
-
-
Product
Turns Ratio and Phase Tester
SS310
-
Turn ratio meter is a reliable test instrument used for product inspection and sample analysis in the manufacture of transformer, radio and TV set or relative scientific research units.
