-
Product
Digital Power Meter (High Accuracy Model)
LS2050
-
LS2050 digital power meter is a new generation intelligent product which adopts digital sampling technology to analysis of the waveform. It has the following features: • Three windows digital display which reduces reading error, intuitive and convenient • Adopts high speed MCU and high precision A/D to control and measurement • All measured data as virtual value, also suit to signal waveform distortion • Fast test • Equipped with RS232 communicate function, can use upper computer software to carry on remote operation, control and read corresponding data, the test data and waveform could be displayed in the PC, Chinese and English operation interface, high intelligent instrument • This instrument provides two kinds of method to calculate total harmonic distortion (THD), IEC and CSA.
-
Product
PCI Data Acquisition Boards
ADDA14-100DMA Dual 14-bit A/D + Dual 14-bit D/A, 25 MS/s
-
Model ADDA14-100DMA contains two simultaneously sampling 14-bit A/D converters and two simultaneous 14-bit D/A converters, and can transfer data directly into host system memory at up to 100 MB/s in 64-bit PCI slots.
-
Product
Amp Booster
CHI680C
-
With the CHI680 Amp Booster, the current can be measured up to 2 A. The CHI680 is compatible with Model 600, 600A, 600B, and 600C series of instruments. You can stack the CHI600/A/B/C and the CHI680 together.
-
Product
Model Based Testing
RTT-MBT
-
Verified Systems International GMBH
The RT-Tester Model Based Test Case and Test Data Generator (RTT-MBT) supports model-based testing (MBT), that is, automated generation of test cases, test data, and test procedures from UML/SysML models. Moreover, it generates traceability data relating requirements, test cases, test procedures, and results.
-
Product
Antenna Test Chambers
-
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
Product
FPGA Signal Processor
376
-
The Model 376 is designed around the Texas InstrumentsADC12D1600 12-bit ADC. The 1.6 GHz sample clock issupplied by either the on-board frequency synthesizer or anexternal source. The frequency synthesizer can be phaselocked to the local 10 MHz TCXO or an external referencecan be used to achieve system-wide phase coherence.
-
Product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
-
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
Product
Adjustable Signal Samplers
7999
-
Now, you can extract a low signal level from a 50-Ohm coaxial system with the Model 7998 and 7999 series of Adjustable Signal Samplers from Coaxial Dynamics. These Signal Samplers are essential tools for spectrum analysis, RF signal scope observation, or frequency counting control.
-
Product
PXIe High Density Matrix Module, 32x8, 1-Pole, 2A, 60W
42-586B-001
-
Our model 40-586B-001, along with the following models 40-584A, 40-585A and 40-587A are high-density single pole PXI or PXIe matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays.
-
Product
FieldFox Handheld RF and Microwave Analyzers
-
Measure with confidence from 4 to 50 GHz - precise measurements agree with benchtop resultsCapture every signal with real-time spectrum analysis (RTSA) up to 50 GHzWithstands your toughest working environments - rugged enough to meet MIL-specsWeighs less than alternative solutions- millimeter-wave models 30% lighter than other handheldsChoose to configure as a cable and antenna analyzers (CAT), vector network analyzers (VNA), spectrum analyzers and all-in-one combination analyzer
-
Product
Data Acquisition Processor Board
DAP 5200a
-
The DAP 5200a model brings many more real-time data acquisition and control applications within the scope of Windows systems. Its onboard 400 MHz processor substantially increases the real-time processing power of the top end of the DAP line. Real-time processing functions include smoothing, filtering, FFT, PID control, and responding to alarm conditions;
-
Product
LabVIEW Tools for Digital Filter Design and Implementation
LabVIEW Digital Filter Design Toolkit
-
The LabVIEW Digital Filter Design Toolkit extends LabVIEW with functions and interactive tools for the design, analysis, and implementation of digital filters. New digital filter users can explore classical designs with the built-in interactive design tools, while experienced users can find a breadth of algorithms, filter topologies, and analysis tools for both fixed- and floating-point digital filters. For fixed-point filters, you can model quantization effects, optimize numeric representation/topology, and deploy the design on a digital signal processor or FPGA using automatically generated ANSI C or LabVIEW FPGA code.
-
Product
Waveguide Bends
-
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
Product
SMD Test Probes
-
The Parrot Clip, model PCM W1 or PCS-MB W1 invention can be connected to resistance’s, diodes, integrated circuits (SOIC, SO) etcThe advantage of the Parrot Clip is given by the double metal connection made between the new metal tip and the steel hooked rod, spring loaded. This connection, being made by metal parts is electrical and mechanical reliable, even if the contact point are small. Connections are resistant even at high temperatures.
-
Product
6-Slot Desktop/Wallmount Chassis
IPC-6806
-
6-Slot Desktop/Wallmount Chassis for Full/Half-Size SBC. Three models with different sizes to support various industrial applications. Supports versatile 6-slot backplanes, Streamlined filtered airflow.
-
Product
High Speed-Large Current DC Electronic Load (CC/CV/CR/CP)
PLZ-4WL Series
-
While the PLZ-4WL series succeeds to the superior operability of our conventional model of the PLZ-4W series, the PLZ-4WL series realizes the high speed rise and fall time (slew rate of 50A/µs.) in the range of low voltage with large current. The PLZ-4WL offers six operation modes, and equips with various features such as sequence operation, switching operation, soft-start function, and time and voltage measurement. The PLZ-4WL applies not only for the conventional load test of the CPU power supply, but also it can be applied to even faster current response test. In addition, the PLZ-4WL is a space-saving design (about 50% less volume of the conventional model) that can save the facility space of the testing site, and it can be applied for the single cell testing of the large scale rechargeable battery.
-
Product
Noise Monitoring Kit
NMS044 SoundAdvisor
-
Larson Davis has created a new standard for portable noise monitoring systems by making the SoundAdvisor Kit Model NMS044 completely wireless with solar charging and 4G wireless while keeping it truly portable. The SoundAdvisor noise monitor includes everything needed for a noise monitor (powered by SoundAdvisor Model 831C Class 1 sound level meter) that can run indefinitely while remaining connected to the Internet making your meter and your data always readily available.
-
Product
RS-232 Opto Isolation Module with DB9 Connectors
Model 9268
-
Ensure clean data transmission and reception between two devices by installing Telebyte Model 9268 Opto Isolation Module with DB9 Connectors. For applications ranging from testing laboratories to factory floors, isolation is a critical component in data communications environments.
-
Product
Model Quality Assurance (MQA)
-
Model Quality Assurance (MQA) is an automated SPICE model validation software which allows you to check and analyze SPICE model library, compare different models, and generate quality assurance (QA) reports in a complete and efficient way. With more than ten years of history, MQA has become the industry standard for SPICE model acceptance and signoff and is widely adopted by leading integrated device manufacturers (IDMs), foundries and design houses.
-
Product
High Impedance Preamplifier
1671
-
The Model 1671 is a single ended low noise field effect transistor
-
Product
DCDC
QQA Series
-
The QQA series features the latest in MOSFET design, state of the art surface mount technology, and offers a 4:1 ultra-wide input range, and efficiencies greater than 80% (typ). Features include continuous short circuit protection, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. All models are packaged in a six-sided shielded miniature case measuring only 1.0” x 2.0” x 0.4” high.
-
Product
Environmental Simulation Chambers
-
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
Product
Magnetostrictive Level Transmitter
DM330
-
The Drexelbrook DM330 magnetostrictive level transmitter is a two wire loop powered intrinsically safe sensor with a configurable 4 -20 mA span.This level transmitter uses proven machine tool positioning accuracy combined with a process compatible float to offer a liquid level, and interface measurement system for the process industry.It comes in a patented low clearance design with all of the sensor’s electronics integrated in a 5/8” diameter sensing tube eliminating the electronics enclosure at the top of the sensor. Not only does this result in reduced cost it also offers its user greater options for insertion and mounting.The DM330 is available in two models.The rigid 316SS model offers a choice of a mini-connector or an optional housing including terminal connectors with zero and span adjustments.
-
Product
Ellipsometer
RC2
-
The RC2 design builds on 25 years of experience. It combines the best features of previous models with innovative new technology: dual rotating compensators, achromatic compensator design, advanced light source and next-generation spectrometer design. The RC2 is a near-universal solution for the diverse applications of spectroscopic ellipsometry.
-
Product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
-
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
Product
Pressure Controllers & Transducers
-
Alicat Scientific, Incorporated
Fast pressure controllers keep your process stable and repeatable. Alicat offers pressure controllers for use in flowing, dead-ended, or vacuum applications. Dual-valve models for closed volumes eliminate the need to continuously bleed expensive process gases. Instruments are available with absolute, gauge, or differential pressure sensors for pressure control as high as 3000 PSIA/PSIG (or 150 PSID) and as low as 2 inH₂O.
-
Product
8-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - PCIe
Model 78131
-
Model 78131 is a member of the JadeTM family of high-performance PCIe boards. The Jade architecture embodies a new streamlined approach to FPGA-based boards, simplifying the design to reduce power andcost, while still providing some of the highest-performance FPGA resources available today. Designed to work with Pentek’s new NavigatorTM Design Suite of tools, the combination of Jade and Navigator offers users an efficient path to developing and deployingFPGA-based data acquisition and processing. The 78131 is a multichannel, high-speed data converter with multiband DDCs (digital downconverters). It is suitable for connection to HF or IF ports of a communications or radar system. Its built-in datacapture feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP
-
Product
Digital Gauge Counter
DG-2310
-
Model DG-2310 is a 2-channel digital gauge counter with multi function to measure and display the dimension and displacement by using our linear gauge sensors (BS/GS-series).Not only the various calculating function of addition/subtraction (A+B, A-B) for 2 channels' data but also that of Max., Min., Range (Max. - Min.) are provided.OK/NG judgment and alarm operation are also possible by using the comparating function.Further, the sequencer, personal computer, recorder and other instruments can be operated by inputting the various signal output from DG-2310, which can make it possible for the data recording and monitoring easily.
-
Product
Handheld Wind Meter
E9350
-
Stationary wind meters have not always been available at all sites where they are needed, such as sites for flying model aircraft, para-gliding, sailing, surfing and many other leisure activities. In addition to the excellent portability provided by its compact design and the innovative “packaging” of the wind wheel, the new ELV handheld wind meter permits not only determination of the wind strength, but also the complex assessment of the weather situation at the site.
-
Product
Gas Analyzers
-
Omega's Handheld Gas Analyzers are ideal for monitoring VOC levels in petrochemical plants, power plants, mining facilities and restaurants. Models available to measure CH4, CO, O2, and H2S
