BER Test
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: BER Testers
-
Product
Bit Error Ratio Testers
M8000 Series
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Test Solution Offering BER Testing
Eye-BERT Micro LR
-
The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Automotive Ethernet Rx Compliance Software
AE6910R
-
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
Product
MIPI Receiver Test Solution
M8085A
-
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Product
Advanced Measurement Package For M8000 Series Of BERT Test Solutions
M8070ADVB
-
The M8070B system software for the M8000 Series of BER Test Solutions can be enhanced by additional software packages, such as M8070ADVB or M8070EDAB to get the best out of the M8040A, M8020A and M8030A J-BERT platforms.The M8070ADVB Advanced Measurement package offers advanced features like automated jitter tolerance test and parameter sweeps, eye diagram measurement or the integration of external equipment such as electrical and optical clock recovery or error analysis using a real-time scope.
-
Product
RF Noise Source
NS-3
-
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
Product
Analog Noise Generator
PNG7000
-
The PNG7000A Series instruments generate white Gaussian noise and provide a summing input to control signal-to-noise (SNR) or carrier-to-noise (CNR) for bit-error-ratio (BER) testing. The output can also be used as a source for Jitter applications.
-
Product
GAOTek Handheld Gigabit Ethernet Tester
A0060001tek
-
GAOTek Handheld Gigabit Ethernet tester is designed for installation and maintenance of 10 M/100 M/1000 M Ethernet networks. It combines the functions of network testing, data packet capture, traffic generation, cable testing and BER testing into one unit. It also integrates full RFC-2544 and Y.1564 tests. Featuring an ergonomic design and 5.0 inch LCD color touch screen, this Ethernet tester helps the front-line field workers to analyze the network quality and locate faults rapidly. Test results can be shown graphically and numerically.
-
Product
Adjustable ISI Channel Emulation Package for M8000 Series BER Test Solutions
M8070ISIB
-
Simplify receiver testing by offering unprecedented flexibility for handling test channels.
-
Product
Error Distribution Analysis Package For M8000 Series BER Test Solutions
M8070EDAB
-
The M8070B system software for the M8000 Series of BER Test Solutions can be enhanced by additional software packages, such as M8070ADVB or M8070EDAB to get the best out of the M8040A, M8020A and M8030A J-BERT platforms.The M8070EDAB Error Distribution Analysis package offers features like burst mechanism detection and analysis, frame loss ratio estimation and error mapping.For instance, you can easily estimate your FEC decoder margin or find the root cause of systematic errors by exploring the error map. The plugin also supports the use of real-time scopes as error detector.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
Bit Error Rate Testers
-
The FarSync BERT Tester provides a comprehensive, simple to use, line testing utility for asynchronous and synchronous lines. Standard BER test patterns are used with real time error counters, user controlled error injection, full line test statistics and APIs.
-
Product
10G & 25G Clock And Data Recovery (CDR) Lab Buddy
-
Discovery Semiconductors, Inc.
Discovery Semiconductors' reference-free 1:1 Clock and Data Recovery (CDR) Lab Buddy, conveniently interfaces with the Bit Error Rate (BER) test equipment and provides a Receive, Reshape, & Retime (3R) solution, which is especially important for transmission experiments. Currently, Discovery offers a CDR Lab Buddy for 10G and 25G data rates.
-
Product
VITA 57.4 FMC+ HSPC Loopback Card
-
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
Product
Variable Attenuators
-
Variable attenuators are an integral part of most BER testing and EDFA characterization setups. All of EXFO's modular (IQS line) and benchtop variable attenuators are built for top performance and pinpoint accuracy. Each model offers a distinct set of features and specifications to suit various testing needs.
-
Product
Cable Free ATE
CABLEFREEATE
test
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
Product
Test Workflow Standard
test
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
test
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Test Management Software
ActivATE™
test
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
Test Instrument
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
PXI Digital Test Instrument
PXIe-6943
Test Instrument
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.This instrument is TPS-compatible with the legacy VXI digital test instrument from Astronics as well as other instrument vendors.
-
Product
Single Site Test Handler
3210
Test Handler
Chroma Single Site Test Handler 3210 supports various package types such as BGA series, QFP series, QFN, TSOP, and more. The handler is primarily designed for early device design and engineering validation.
-
Product
Magnetic Material Test Fixture
16454A
Test Fixture
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
Product
6TL29 Semi-Automated Test Platform
AQ377
Test Platform
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
Product
6TL10 Table Top Test Base
H71001000
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
PXIe Optical Test Modules
Test Module
Coherent Solutions’ expanding portfolio of PXIe optical test modules bring a wide range of new mixed-signal test capabilities to the PXI platform. The new modules offer seamless integration with PXI Platform and deliver reliable and repeatable results across a wide range of optical and mixed-signal test applications.
-
Product
LTE/LTE-Advanced Analysis Using NI PXI RF Test Instruments
NI-RFmx LTE/LTE-Advanced
Test Instrument
Highly optimized RF measurement experiencePerform physical layer analysis on LTE cellular signals including MODACC, ACPR, CHP, OBW, and SEMIncludes support for TDD, FDD, and LTE-Advanced signals specified in 3GPP standards release 12Simple access to advanced measurement parallelism





























