Validators
Assure standards are met.
-
product
Diagnostic Test System™
The original Teseda system for bench-top stimulus, test pattern debug, validation, device failure mode stimulation in-situ with other Failure Analysis lab equipment such as an EMMI, etc.
-
product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Ada Embedded Software Test Solution
VectorCAST/Ada
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing Ada software components necessary for validating safety- and mission-critical embedded systems. VectorCAST/Ada parses your source code and invokes code generators to automatically create the test code (stubs and drivers) required to construct a complete, executable test harness.
-
product
Protocol Analyzer and Exerciser
Keysight's protocol test solutions for each technology typically consists of both protocol analyzer application as well as a stimulus solution, such as an exerciser or traffic generator. Keysight's protocol test solutions combine multi-protocol analysis, traffic generation, performance and conformance verification to debug, validate and optimize your designs using high speed protocol standards.
-
product
ccVPX Card
EXC-4500ccVPX/xx
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The EXC-4500ccVPX/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
product
GMSL3
FRAMOS is the first company in the market to integrate Analog Devices’s new GMSL3 technology into an embedded vision environment. GMSL3 can transmit high frame rates (4K, 90 fps) as far as 14 meters with unprecedented efficiency. This interface is well suited for applications where the MIPI CSI-2 (D-PHY) length restrictions are not sufficient, while at the same time, a highly durable cable with low power consumption and low cost are essential. Camera developers can use the flexible FRAMOS Sensor Module Ecosystem to validate a variety of image sensors in the lab and in the field while taking advantage of the interface’s features.
-
product
AWG
With the accelerated growth of hyperscale datacenters, Ethernet network infrastructure performance demands are increasing exponentially, and customer expectations for high-speed data throughput are at an all-time high.Other high-speed I/O protocols such as PCIe Gen 5 and 6 are also gaining momentum. Arbitrary Waveform Generators are the ideal general-purpose development tool for validating high-speed receivers and are extremely flexible instruments for coherent module development.
-
product
End-To-End Performance Testing
IxLoad Wireless
Keysight Network Applications and Security
IxLoad Wireless enables mobile operators and equipment manufacturers to test and validate complex wireless networks and components for greater end-to-end service quality. This “lab to live” LTE testing solution recreates networking environments and real-world subscriber traffic, such as voice, video, and data. At the same time, it emulates multiple mobile subscriber activities—including handovers, TAU, and idle-connected transitions—for comprehensive test coverage. Whether modeling the behavior of thousands of subscribers or measuring end-user experience, IxLoad enables mobile operators to fast-track new networks and services with confidence.
-
product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Universal Software-Defined Radio
VPX3-E320
Curtiss-Wright Defense Solutions
Designed for superior durability and reliability, the VPX3-E320 incorporates Curtiss-Wright’s industry-leading rugged hardware design and validation practices to meet the stringent requirements of the most demanding front-line environments. Paired with the industry-leading UHD based software-defined radio workflow, this product is truly unique.
-
product
Autonomous Vehicle Simulation
Ansys Autonomous Vehicle Simulation provides a solution designed specifically to support developing, testing and validating safe automated driving technologies. This autonomous vehicle simulation solution saves significant time and costs versus traditional development and testing methods by allowing you to exercise your AV/ADAS software stack in a closed loop, with sensor-accurate synthetic data in software-in-the-loop or hardware-in-the-loop context with the driving simulator of your choice.
-
product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
product
Easy Navigation Package for Optimal Raman Imaging
EasyNav
The new EasyNavTM package makes it easy to navigate through your image and acquire sharp Raman images in the blink of an eye, thanks to three new revolutionary applications: NavMapTM, NavSharpTM and ViewSharpTM. With the groundbreaking EasyNavTM package, it is fast and easy to navigate in-focus, in real-time, to identify the region of interest and obtain sharp, clear Raman chemical images. EasyNavTM has been tested and validated on a large variety of samples. HORIBA NavMapTM+ NavSharpTM+ ViewSharpTM apps can be used together or separately to deliver a powerful user experience for all Raman users.
-
product
Security Policy Change Automation
FireFlow
Confidently automate your security policy change process - from planning through risk analysis, implementation and validation.
-
product
Wi-Fi Performance Validation
Excentis offers a unique testing service in a real home a realistic, static, residential environment with controllable interference. This setting enables the customer to statistically compare Wi-Fi access points, as the performance is measured by a robot from different physical locations in the home, with different client types (laptops, tablets, smartphones,...) and with different operating parameters. This program can also be used for benchmarking.
-
product
HDMI 2.1 Receiver Compliance Test Software
N5991HP1A
N5991HP1A HDMI electrical performance validation and compliance software solution offers a complete test execution environment for validating and troubleshooting the electrical performance of HDMI 1.4 and HDMI 2.1 sink devices.
-
product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
PXI Signal Insertion Switch Module
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
product
Vibration Testing
Automobiles, electronics, heavy equipment, home appliances and more…consumers want dependability and manufacturers need to deliver quality. The need to comprehensively test components and systems for shock and vibration resistance can often be the key to long-term product success. Trialon’s experienced team will be your partner to provide complete satisfaction throughout the product validation process.
-
product
LPDDR3 178-ball BGA Interposer For Logic Analyzers
W3301A
The W3301A LPDDR3 rigid BGA interposer for LPDDR3 178-ball DRAM enables capture of simultaneous read and write traffic at data rates in excess of 1866 Mb/s. E5406A Soft Touch probes and U4201A cables connect the W3301A LPDDR3 BGA interposer into the U4164A logic analyzer module. The W3301A LPDDR3 178-ball rigid BGA interposer allows signal access to the LPDDR3 signals critical to your debug and validation effort through a U4164A logic analyzer. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DRAM using a LPDDR3 178-ball riser (included) or an optional 3rd party socket (not provided), enabling operation and acquisition of LPDDR3 signals.
-
product
Satellite Network Simulator
The DataSoft Satellite Network Simulator is a real-time software tool capable of simulating satellite links by operating as a hardware-in-the-loop tool for layer-2 verification and validation, or, as an offline planning tool for capacity and availability analysis for planned deployments.
-
product
JTAG (and IJTAG) Environment Tool Suite
SAJE
SAJE is the SiliconAid Suite of JTAG related standards focused tools for chip development, verification, validation and patterns generation of ATE, Board, and System Test. Each tool can be used as a point tool by itself to compliment other tools in your flow. However, the SAJE Tool Suite used together in a flow can provide a total solution that also leveraging previous steps for debug and analysis.
-
product
Electrical DfT & Fault Coverage Analyzer
TestWay
TestWay's electrical DfT analyzer enables designers to validate designs at the schematic capture stage, to ensure that adequate measures have been included to comply with the manufacturers test requirements. The ability to verify that PCB designs have been developed with adequate Design-for-Test in mind, is key in determining the most effective test strategies and accurately calculating fault coverage, which is crucial in improving competitive advantage, lowering cost and ensuring product quality.
-
product
Network Security
TrustMonitor™
TrustMonitor™ provides continuous monitoring of the trust network by:*(Analyzing content & constraints for validity of credentials*Monitoring that certificate authorities are available to support validation*Easily scaling to incorporate new certificate authorities (no agent required)
-
product
Absorber Lined Shielding Enclosure Measurements
ALSE
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
-
product
Torque Carts
AIMCO offers torque carts for "lineside" or "point of use" tool validation and calibration. Our torque carts allow testing of tools on repeatable joint simulators and "in process" use on production joints, allowing users to identify process capability. There are multiple torque cart options:
-
product
Light Obscuration
FlowCam LO
Yokogawa Fluid Imaging Technologies, Inc.
Our new FlowCam LO instrument combines our patented flow imaging microscopy technology with an embedded light obscuration particle counter to provide you with the necessary data for USP regulations and validation with images.
-
product
PXIe-6594, 28 Gbps, 8-Channel PXI High-Speed Serial Instrument
786939-01
PXIe, 28 Gbps, 8-Channel PXI High-Speed Serial Instrument. - The PXIe-6594 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale+ FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe-6594 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
product
Test Tool
Iron - IEC 60870-6
Iron is a Windows™ application that creates compliant IEC 60870-6 (TASE.2/ICCP) Applications, both unidirectional and bidirectional. Iron is a highly configurable tool with multiple simulation options for changing Data Model values and generating valid message traffic. Support for Read, Write, Reporting, Discovery, Controls, and Dynamic DataSets are built into the tool.
