Serial Digital Interfaces
A family of digital video interfaces standardized by SMPTE.
-
Product
64-CH Isolated Digital I/O Modules
cPCI-7432/7433/7434
Digital I/O Module
- Two external interrupt sources for cPCI-7432/7432RP/7433- 3U Eurocard form factor, CompactPCI compliant (PICMG 2.0 R2.1)- 32-CH isolated digital inputs & 32-CH isolated digital outputs for cPCI-7432- 64-CH isolated digital inputs for cPCI-7433- 64-CH isolated digital outputs for cPCI-7434/7434P- 5000 VRMS isolation voltage
-
Product
ARINC PCI Express 4 Lane Interface Cards
PCIE4L-A429
Interface Card
Alta Data Technologies’ PCIE4L-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal. The 4 lane card (PCIE4L) is normal 1/2 height common for most desktop and larger server systems.
-
Product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
Digital Module
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
Handheld Clamp Meter, 3 ½ Digit
U1213A
Digital Multimeter
Handle large currents up to 1000 A safely with 2-inch large jaw opening. Wider range DCV, ACV and resistance. Keysight Remote Link Solution allows datalogging wirelessly via Bluetooth.
-
Product
PCI-6513, 64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated Digital I/O Device
778970-01
Digital I/O Module
The PCI-6513 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6513 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
USB-6501, 24-Channel, 8.5 mA, Digital I/O Device
779205-01
Digital I/O Module
The USB-6501 is a portable, bus-powered USB digital I/O device, providing reliable data acquisition and control at a low price. The device provides overvoltage protection its digital I/O lines and a 32-bit counter. With plug-and-play USB connectivity, the USB-6501 is simple enough for home and academic applications, but robust and versatile enough for laboratory and industrial applications.
-
Product
Digital I/O
IP-DIGITAL482
Digital I/O Module
IP-DIGITAL482 is a single-wide IndustryPack configured to maximize the number of digital I/O lines. The 48 lines are accessible as individual bits or as bytes. These lines may also be used for 8-bit and 16-bit I/O with handshake lines. IP-DIGITAL482 is a drop-in replacement for the IP-DIGITAL-48.
-
Product
High-Speed A/D 8-Bit Digitizers
Digitizer
GaGe 8-bit resolution digitizer models divide the input voltage range into 256 different digitization levels with sampling rates at up to 4 GigaSamples per second on 1 channel or 2 GigaSamples per second on 2 channels with input bandwidths of up to 1.5 GHz, deep onboard sample memory up to 16 GS (16 GB), and true ENOBs of up to 7.6 bits.
-
Product
Handheld Digital Multimeter, 3 ½ Digit
U1232A
Digital Multimeter
Ergonomic shaped 6K counts DMM with flashlight, low input Z mode and continuity visual/audio alerts. Keysight Remote Link Solution enabled.
-
Product
PXIe-8430, 16-Port, RS232 PXI Serial Interface Module
781472-02
Serial Interface
16-Port, RS232 PXI Serial Interface Module—The PXIe‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
CAN Interface Device
CAN Interface
CAN Interface Devices communicate using onboard transceivers for High-Speed/Flexible Data-Rate, Low-Speed/Fault-Tolerant, and/or Single-Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from Fieldbus Exchange Format (FIBEX) and Database Container (DBC) files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
Power Management & MMI Module
H73000700
Interface
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
68 POS VHDCI Conn to Eight 9 POS D-SUB, RS 485, 1M
197546-01
Serial Cable
68 POS VHDCI Conn to Eight 9 POS D-SUB, RS 485, 1M
-
Product
cRIO-PB-MS, Master/Slave, C Series PROFIBUS Interface Module
781352-01
Interface Module
Master/Slave, C Series PROFIBUS Interface Module - The cRIO-PB-MS connects NI programmable automation controllers (PACs) to PROFIBUS industrial networks as powerful masters or slaves. The interface includes the NI‑PROFIBUS for CompactRIO instrument driver for human machine … interface (HMI) and SCADA applications, as well as a graphical networking Configurator software. You can perform PROFIBUS device automated test using these interfaces. The cRIO-PB-MS is compatible with only CompactRIO systems.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-2IPC-6U
Digital I/O Module
The CPCI-2IPC-6U module provides a high performanceflexible I/O scheme, that supports industry standard IndustryPacksÔ. For application requiring high performance, highdensity I/O or unique combinations, the CPCI-2IPC-6U is theperfect solution. The Local DSP’s can be used to simplymove data to and from the CPCI bus or provide localprocessing functions such as local PID controls, FFT’s, digitalfiltering, etc.
-
Product
Interface Board, Low Cost, 8:1 Ethernet RJ45
40-965-901
Interface
Low cost converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
PXI Remote Control Interface Cable, 7m
41-924-700
Remote Interface Cable
The 41-924-700 is a 7m cable accessory for the PCIe to PXI Remote Control Interface Kit. The kit provides a seamless connection between a PC’s PCIe slot and a PXI chassis and is suitable for providing an interface to any PXI chassis.
-
Product
10-CH General-Purpose Timers/Counters & 8-CH Digital I/O Card
PCI-8554
Digital I/O Module
- Supports a 32-bit 5 V PCI bus- On-board four 82C54 programmable timer/counter chips- 10-CH independent 16-bit down counters- 1-CH 32-bit cascaded timer- Four programmable clock sources for each timer/counter
-
Product
PXIe-5763 , 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785160-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Network Interface Card
XMC477RC
Interface Card
The XMC477RC is a quad switched mezzanine card (XMC) compatible module providing a 4-channel Gigabit Ethernet Small Form Factor pluggable (SFP) interface.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
DN2.222-02
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 2 Channels, 1.5 GHz Bandwidth
DN2.223-02
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
CEI-2x10GBASE-T
Network Interface Controller
- Support up to two 10GbE BASE-T interfaces- Marvell AQR113C inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-03
Digital Waveform
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785957-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Network Interface for PCI Express
PCIe-ASM-NIC
Network Interface Controller
Avionics Interface Technologies
Quad port FC-AE-ASM Network Interface Controller for PCI Express
-
Product
NI-5732, 80 MS/s, 14-Bit, 2-Channel Digitizer Adapter Module for FlexRIO
781658-02
Digitizer
The NI‑5732 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 80 MS/s. You can use the NI‑5732 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5732 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Handheld Clamp Meter, 3 ½ Digit
U1212A
Digital Multimeter
Handle large currents up to 1000 A safely with 2-inch large jaw opening. Keysight Remote Link Solution allows datalogging wirelessly via Bluetooth.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s, 500 MHz Bandwidth
DN2.221-04
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.445-08
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
