Filter Results By:
Products
Applications
Manufacturers
Torque Sensors
measure rotational twisting force.
See Also: Torque, Torque Testers, Torque Transducers, Torque Meters
-
product
Non Contact Flange Torque Transducer
FF425
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
product
Calibration Equipment
Calibration is the method of comparing tools and measuring devices to higher accuracy standards. Torque calibration equipment is the official means by which torque testers and sensors are calibrated and are traceable to National or International Standards, such as N.I.S.T and ISO. In order to maintain precision accuracy, it is essential that torque measuring equipment be calibrated regularly. By equipping your team with Mountz calibration equipment, you can avoid the costly chore of sending your torque tools to the lab whenever they fall out of alignment.
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
product
Calibration Hangers And Weights
Calibrated Dead Weight are the official means by which torque analyzers and torque sensors are calibrated and are traced to National or International Standards, such as N.I.S.T, ISO and others. Many industries like as medical, aerospace, nuclear and others continuously calibrate their measuring equipment to comply with government regulations. For companies that prefer to have calibration capabilities in-house when their calibration requirements become extensive, they need calibration equipment.
-
product
Force Sensors
Here at Flintec, our force sensor range provides solutions that integrate effectively into a wide variety of industrial applications. They include customized load pins, extensometers, torque sensors and a range of miniature force sensors.
-
product
Torque Transducers
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
product
Instrumentation
Complementing our range of force and torque sensors, we offer a comprehensive range of graphical displays, including the Digiforce, which are PLC controllers and data loggers all in one. Together with a fully comprehensive range of standard high speed load cell displays with analogue output.
-
product
Test Of Hand Pneumatic Tools
The measuring system consists of a test site and a control rack. The test site is equipped with a mounting for the test tool with measuring sensors: vibration, torque and speed, as well as a pneumatic regulator, a filter and a powder type brake clutch. The maximum torque test is performed until the rotation is completely stopped. The screen displays both the directly measured maximum torque and the calculated maximum power of this sample. At the end of the test, the results are presented to the operator on the monitor screen.
-
product
Low Torque Reaction Sensors
MTX
The MTX is a low torque sensor designed for calibrating and testing small hand screwdrivers, torque wrenches and power tools. With its low profile design, the calibration instrument can be used for automated applications, by mounting it to a palletized system. This saves time as there is need to remove the driver from the robot or off the automated system for calibration. These versatile torque sensors are used in conjunction with a torque tester.
-
product
Measurement
Multichannel Strain Gauge Meter
The Software Multichannel strain gauge meter is used for performing all types of strain gauge measurements using strain gauge sensors (for instance, force and torque sensors, bridge and semi-bridge circuits based on resistive strain sensors), strain measurement data acquisition modules ZET 017-T and digital strain gauge sensors of ZETSENSOR series. The program enables simultaneous processing of up to 128 measuring channels using strain gauge station and up to 500 measuring channels in the case if digital sensors are used.
-
product
Brushless Rotary Torque & Angle Sensor
BLRTSX-A
The Mountz brushless rotary torque & angle sensors an ideal torque-measuring solution for applications where accuracy and reliability rank paramount. Can be used for testing real-time torque or for checking the breakaway torque (first movement) of a fastener.
-
product
Amplified Torque & Load Cell Indicator
9834
For use with amplified load cells and rotary torque sensors. Features 120 readings per second, programmable +/-10V or 4-20mA analog output, peak and valley monitoring, RS232. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector.
-
product
Rotary Shaft to Shaft Torque Sensor
Futek Advanced Sensor Technology, Inc.
The Rotary Shaft to Shaft Torque Sensor category has Torque Sensors which are used in slip ring and non contact rotary torque measurements. The most common utilization for these models is for inline/reaction applications, where measurements can be made in both clockwise and counterclockwise directions. The Rotary Shaft to Shaft Torque Sensors are CE certified and utilize a bonded metal foil strain gauge. As with most FUTEK products, we will gladly work with you to customize or modify our Torque Sensors to meet your precise needs.
-
product
Torque Sensor
Futek Advanced Sensor Technology, Inc.
Torque Sensors manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), offering a huge selection of Torque Sensors, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.A Torque Sensor, is a transducer that converts a torsional mechanical input into an electrical output signal. Torque Sensor, are also commonly known as a Torque Transducer.
-
product
Socket Wrench Torque Sensor Rotating Type
RSS SERIES
Our RSS Series rotating socket wrench torque sensors are available in ranges from 10 ft-lbs. through 250 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. Unlimited rotation of the ball bearing supported sensor shaft allows monitoring of the total fastening cycle. The sensing element incorporates bonded foil strain gages of the highest quality, along with coined silver slip rings and two silver graphite brushes per ring for data transmission.
-
product
Run Down Adapters
Mini RDA
The mini RDA unit with fastener is designed for low torque sensors. Engineered to provide consistent and reliable torque readings for use with low torque power tools. The mini run down adapter is mounted in-line between the tool drive and torque sensor.
-
product
Load Cell Amplifiers
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
product
Rotary Hex Drive Torque Sensor
Futek Advanced Sensor Technology, Inc.
The Rotary Hex Drive Torque Sensor category has Torque Sensors which are used in slip ring and non contact rotary torque measurements. The most common utilization for these models is for inline/reaction applications, where measurements can be made in both clockwise and counterclockwise directions.
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
product
Torque Sensors & Torque Transducers
Datum Electronics is a world-leading designer, manufacturer and supplier of torque sensors, torque transducers & torque meters, bolt-on strain, weight & load sensors, as well as shaft power measurement solutions.With 30 years of expertise in torque and shaft power measurement, we research, design and manufacture our reliable & accurate torque sensors in-house. Besides, our team specialises in providing both industry standard off the shelf solutions, as well as bespoke custom torque sensors, built to your own specifications and requirements.
-
product
Digital Telemetry Solutions
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
product
Smart Sensors
Datum Connect
Datum Connect is the latest configuration and logging application, which supports the latest torque sensor technology. Datum Connect allows simple, quick and easy configuration of all Datum torque sensors, enabling users to see torque sensor outputs in real time in a format of their choosing.
-
product
Calibration Segment Arm
A torque analyzer or a torque sensor are a finely tuned instrument designed for testing and monitoring torque applications. In order to maintain accuracy, it is crucial that torque measuring equipment be properly calibrated regularly. Segment arm is engineered for calibrating torque analyzers and sensors and ensuring instruments are traceable to National or International Standards, such as N.I.S.T and ISO.
-
product
Strain Gauge Sensor
ZET 7010
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
product
Torque Verification
90229
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
-
product
Peak Track Instrument
90323
The model 90323 Peak Track Instrument is a general-purpose sensor readout device designed to complement our AutoID line of load cells and torque sensors. AutoID is a term that indicates that the calibration information for a sensor is stored on a chip inside the sensor’s connector. AutoID allows true “plug and play” operation without manual calibration procedures of any kind. The unit is also equipped with a 2-line alpha-numeric display and single button operation for simplicity.
-
product
Calibration Wheel
A torque analyzer or a torque sensor are a finely tuned instrument designed for testing and monitoring torque applications. In order to maintain accuracy, it is crucial that torque measuring equipment be properly calibrated regularly. Calibration wheel is engineered for calibrating torque analyzers and sensors and ensuring instruments are traceable to National or International Standards, such as N.I.S.T and ISO.
-
product
Custom & Special Models
Futek Advanced Sensor Technology, Inc.
Custom Load Cells manufactured in the US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Custom Force Sensors and Custom Torque Sensors utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
-
product
Force & Strain Measurement
Load cells, tank weighing devices, balances, scales, force gauges, torque sensors and strain gauges including diaphragm, dual parallel, linear, rosette, T-rosette, and torsion and shear types.
-
product
Instrumentation And Signal Conditioners Products
Stellar Technology offers a full line of readout meters, in-line amplifiers and signal conditioners to complement our broad variety of pressure, load/force/torque, displacement, and temperature sensors. If you’re in need of reliable signal conditioners for your essential operations, our diverse options can provide a solution. Read on to discover all that Stellar Technology can offer your company.
