Protocol
A standard way of controlling hardware and/or software that enables connection, communication and data transfer.
See Also: NTCIP, Communication Protocol
-
product
LAN⇔RS-232C Conversion
SI-60F
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
product
PCIe-7842, Virtex-5 LX50 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device
781101-01
Virtex-5 LX50 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7842 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7842 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
Single / Dual channel Dual Redundant DDC Controller
PCI-1553DDC-2
The PCI-1553-DDC-1/2 implements a complete single channel dual-redundant MIL-STD-1553 bus terminal on a half size PCI Card. Full BC/MT/RT modes are supported. 0°C to 70°C operating temperature is standard. Included is an DDC Enhanced ACE intelligent communications protocol engine, dual transceivers and encoder / decoders, shared memory, and management logic.
-
product
Rugged Cisco IP Router With Firewall & PoE+
NetSys-5311
The rugged design of the NetSys-5311 brings Cisco’s ESR-6300 Embedded Services Router and its Cisco-certified mobile IP routing protocols to the network edge in a SWaP optimized chassis.
-
product
AFDX® / ARINC 664 Test And Simulation PCIe Module
PCIe-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
PCIe 3.0 Protocol Analyzer
Summit T34
The Teledyne LeCroy Summit T34 PCI Express protocol analyzer is designed for PCIe storage, add-in card and embedded application developers. It supports x1 to x4 lane widths with the capability of expanding to x8 with two boxes connected together, and deep buffer memory that is expandable from 4GB to 64GB ideal for storage analysis, the Summit T34 provides unmatched capability and flexibility for developers and users of advanced PCI Express products. Teledyne LeCroy has been the leader in NVM Express and SATA Express protocol analysis since 2010. This storage analyzer incorporates all of these powerful legacy features and adds the latest in storage queuing performance analysis.
-
product
Optical Assemblies
Our team works closely with your design team to develop a custom, long-term production solution that fits your specific program. Our manufacturing niche is in low- and mid-volumes (10 to 1,000 units) for assemblies with demanding or non-standard optical performance requirements. Along with Promet’s rigorous QC protocols, our in-house testing labs and engineering support ensure a well-controlled process and predictable results.
-
product
OBD Protocol Diagnostics
Our innovative OBD Protocol Diagnostics comes with diagnostic break-out boxes and CAN network testers which can expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test ECU signals.
-
product
Substation Alarm ManagerAnnunciation and Data Viewer
SAM
Applied Systems Engineering, Inc
Applied Systems Engineering, Inc.''s Substation Alarm Manager (SAM) was developed in order to provide Power Utilities with a simple way to show the current status and data within a substation. SAM Substation Annunciator utilizes our extensive protocol library and allows for a wide variety of substation equipment to be monitored. Data can be acquired either by eavesdropping on an active circuit or directly polling an RTU/IED. Collection data is transmitted to SAM through the OPC protocol. This allows SAM to perform its alarm monitoring function either locally at the substation or at a remote site.
-
product
ANSI X3.28 To Modbus RTU - Serial To Modbus RTU Converter
Designed for legacy systems where there is a need to replace older X3.28 protocol Controllers and with new Modbus RTU Controllers. The Model 2399 provides ANSI X3.28 to Modbus RTU Conversion without changing the existing system software. The 2399 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands when controlling Modbus RTU devices.
-
-
product
Branch Circuit Monitor
Multiple branches of load can be monitored togetherCan group the device as 3 phase load and single phase loadFaster communication through RS485 port (Modbus protocol)Simultaneous sampling of Volts and AmpsAccuracy Class 1.0 as per IEC 62053-21 & Class 0.5 as per IEC 62053-22 StandardsDisplays more than 25 parameters
-
product
Conformance Testing Software
Clarinet-TTCN VOIP ETS
Protocol: the ITU-T H323 and H225 define VOIP call signaling protocol for "Packet based multimedia communication systems".IUT: H323/H225 Terminal, gatekeeper and gatewayATS: Based on first ETSI Drafts TS 101 804-2 and 101 804-3 rewritten by ACACIA
-
product
12 Channels, ARINC 429/575 Communications
AR1
The AR1 provides an ARINC 429/575 communications interface with 12 channels. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer. Each channel is programmable as either Tx or Rx.
-
product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
product
C Series CANopen Interface Module
The C Series CANopen Interface Module is a high-speed interface for developing CANopen applications. CANopen is a higher-level communication protocol based on the controller area network (CAN) physical layer. It was designed for motion-oriented machine control networks, but now it is used in a variety of products and applications, including medical equipment, maritime electronics, building automation, and more. The C Series CANopen Interface Module can transmit and receive process data objects (PDOs) and service data objects (SDOs) according to CiA-DS 301. Using the NI-Industrial Communications for CANopen driver, you can batch edit SDOs, configure slave nodes with LSS services support, as well as perform network management (NMT), heartbeat, node guarding, and CANopen synchronization functions.
-
product
EMC Test Systems
IEC61000
N4L are the only IEC61000 EMC test system manufacturer in the world* with an on site UKAS ISO17025 calibration laboratory offering accreditation to IEC61000-3-2, IEC61000-3-3, IEC61000-4-7 and IEC61000-4-15. Calibration and trace-ability are a vital aspect of any EMC test solution and the coverage provided through N4L’s UKAS Laboratory is comprehensive. N4L’s IEC61000-4-15 calibration procedure is particularly noteworthy as it covers the entire test protocol detailed in Annex C of IEC61000-4-15. It is commonplace for specific parameters within IEC61000-4-15 (d parameters are frequently omitted from calibration procedures) to remain untested during typical flicker calibration due to the difficulty in providing trace-ability for such measurements. All tests within the test protocol of Annex C are included within the scope of accreditation and calibration procedures at N4L.
-
product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
product
Network Gateways
The communication protocol of the master controller, Factory Automation (FA) network, is converted to Oriental Motor's own RS-485 communication protocol. Connection to Oriental Motor's network compatible products is completed with one RS-485 communication cable.
-
product
Electric Vehicle Service Equipment Test System
T4350
With the growing demand for electric vehicles (EV), there needs to be a simple and accurate method to test EV charging systems. Test the accuracy of AC and DC voltages and currents with TESCO’s Electric Vehicle Service Equipment (EVSE) Test System TS400. The TS400 is a valuable set with complete testing capabilities and caters to every possible EVSE charging protocol in the world (AC and DC). EV charging stations are popping up all over as the sale of electric vehicles increase. Many states or counties are now mandating testing for these charging stations. TESCO’s TS400 makes testing these chargers easy! TESCO’s EVSE Test Systems test the accuracy of energy delivery using a transactional mode compatible with Handbook 44 provisions. The TS400 Test System includes a T4000 EVSE Tester and a PL4000 EV Load Emulator. Reach out to your TESCO Representative for more information!
-
product
Advanced ARINC-429 Testing Ethernet Appliance - Parametrics TX Variable Voltage, Digital Signal Generator and RX Signal Capture
ENET-A429P
eNet-A429P™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). eNet-A429P is a small, low-power, device ideal for details ARINC signal testing with variable voltaqe control of the first 3 TX channels. Alta has combined the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, with a real-time IP/UDP thin server. The customer can implement their application with the same feature-rich application programming interface, AltaAPI™, as used with standard cards – often without even recompiling – the utlimate in code portability.
-
product
cRIO-9805, 4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO
786993-01
4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO - The cRIO-9805 is a 4-port Ethernet switch that provides additional ports with 802.1AS network synchronization capability over the 1000 Base-TX network interface. This module supports TCP/IP and UDP network protocols in DHCP + link-local, DHCP, static, and link-local network IP configurations. The cRIO-9805 auto-negotiates communication rates of 10, 100, or 1000 Mbps with its four internally switched ports.
-
product
Kalypso-Military Grade Secure Messaging Application
Secure Messenger Application (Code name : Kalypso) is a revolutionary Application designed to provide its users with end-to-end secure communication (Text, Voice and Video) using proprietary robust communication protocol / 256 bit military grade encryption algorithm with an On Premises Server.
-
product
8AI Modbus RS-485 Remote I/O
ND-6117
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
LAN⇔RS-232C Conversion
SI-60
SI-60 is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. Therefore, you can use it for factory automation without worry.
-
product
Networking Solutions
Thread
Thread is an IPv6-based mesh networking protocol designed as a reliable, low-power, secure, and scalable networking solution for connecting Things to the IoT. As a founding board member of the Thread Group, Silicon Labs helps accelerate time to market with proven mesh networking hardware and software solutions.
-
product
Bus Analyzer / Exerciser
VME850P0
The VME850P0 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P0 connector. This module allows the user to monitor and stimulate the A, B, C, D and E rows of the 95 pin P0 connector. Although the VME850P0 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P0 connector must be less then 5V in order to prevent damage of the analyzer.
-
product
Garmin LIDAR-Lite V4 LED
Distance Measurement Sensor (Qwiic)
The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone, robot, IoT, or unmanned vehicle operations when space is tight and power is limited. This sensor has up to a 10 meter range, 1cm resolution, and requires 85mA during data acquisition. The user can read and write to the LIDAR-Lite v4 using the I2C protocol; this is where the addition of the SparkFun Qwiic system really shines. The LIDAR sensor requires 5V to operate but runs on 3V3 logic. With a 5V boost circuit and an easy-to-use Qwiic connector you can power the sensor and get distance measurements over Qwiic all with a single piece of hardware.
-
product
Media Gateway
A Media Gateway is a networking device that provides valuable and essential functions for organizations, service providers, and network operators. When interconnecting traditional time-division-multiplexed (TDM) telephony systems with modern voice-over-internet protocol (VoIP) systems, a VoIP media gateway works by providing protocol conversion (translation) and interoperability between the two network technologies. Also known as an IP media gateway or SIP media gateway, the device converts a traditional analog plain-old-telephone-system (POTS) voice signal or related digital telephony signals such as T1, DS3, STM1 or OC3 into packets for transmission over a data network such as the Internet, private IP Network or a corporate LAN. When the legacy system is based on digital integrated services digital network (ISDN) technology, the device may be called a digital VoIP gateway or ISDN media gateway. Some manufacturers combine gateway functionality with WAN-access (internet-access) capability into a single device or network appliance. Such a dual-purpose device may be known as an access media gateway.
-
product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
