Hard Drive
Store data on magnetic surface plattens.
-
Product
6U VME Storage Module, 3 Drives, 5050 / 5051
5050
-
The 5050 is a 6U VME Storage Module with three 2.5” SSD in a single slot. Each SATA drive is accessible via front panel or RTM. Can be integrated into a multi-slot storage array using an external SATA RAID controller.
-
Product
Brinell Hardness Tester
-
Using a carbide ball penetrator, and applying loads of up to 3,000 kgf, Brinell hardness tester following ASTM E-10 are widely used on castings and forgings. This method requires optical reading of the diameter of ball indentation, and using a chart to convert the average measurement to Brinell hardness value. We offer low cost handheld Brinell scopes as well as a popular line of Automatic Brinell Microscopes for high frequency of testing. . Qualitest also offers Automatic In-line hardness testers for high volume testing.
-
Product
Stationary Drive Test System
ACTAS CF80
-
Stationary test system for sequential final factory tests and function tests on up to 8 drives. The drive test system is operated and controlled with the ACTAS operating software. The test position is selected using the multiplex method. The test system can reproduce drive control with the aid of a logic module. This makes it possible to test any drive even if there is no control unit.
-
Product
Medium Voltage Drives
-
Target markets include Oil and Gas, Water and Wastewater, Power Generation, Rubber and Tire, Mining, Cement and other industrial applications. They can be applied equally well to applications requiring Constant Torque (CT) output performance as well as the traditional Variable Torque (VT) pump and fan loads.
-
Product
Full-Automatic Testing Machine for Hard Board Car
U690HDIR
-
1. CCD automatic alignment, the alignment accuracy reaches ± 15μm2. Support layout test, displacement function3. Automatic marking function
-
-
Product
Shore Hardness Tester
DRK201
-
Shandong Drick Instruments Co., Ltd.
The Shore hardness tester is applied to test the hardness of vulcanized rubber and plastic.
-
Product
Four-Wheel Drive Dingle Roller Dynanometer for Cars with Axle Load of up to 2.4T, for Installation in an Existing LPS 3000 Dynanometer
MSR 500/2 CAR 4WD (LPS 3000) | VP 230038
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD is suitable for installation in an existing LPS 3000 base.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
Product
Compact Tablet Hardness Tester
HC 7
-
The new member of our Lab.line product family: the HC 7 hardness tester for manual use in the laboratory.Equipped with a touch display and the new database-driven touch software, the HC 7 impresses with its exceptional user-friendliness. The new software can be operated intuitively and is equipped with all important functions for quick operation.Start your quick, direct and product testing with just a few clicks directly via the touch display and set up to 50 products. Reports can be printed externally via USB or LAN interface. It is also possible to connect DYMO* and EPSON* roll printers (*special models only).
-
Product
Hardness Test Blocks
-
Used to verify the hardness tester's performance and provide data in order to calibrate the hardness tester.
-
Product
Microindentation Hardness Testing Systems
LM Series
-
Perfect for a production facility or a research lab, LECO's LM Series Microindentation Hardness Testing Systems offer a variety of models (including analog and digital) with the advanced features that meet your requirements and budget.
-
Product
Ultrasonic Portable Hardness Tester
MET-U1A/MET-U1A50/MET-U1A100/MET-U1A110
-
The PHASE II ultrasonic portable hardness testers are capable of measuring the surface hardness of a broad variety of metals on flat, round, thin or large surfaces. Unlike the standard Dynamic hardness testers, these "state-of-the-art" portable hardness testers incorporate "Ultrasonic UCI" technology, which enables the hardness testing of very thin and small workpieces, which otherwise could not be tested accurately using a portable device.
-
-
Product
Measuring Devices for Magnetically Hard Materials
MAG-ST100
-
The computerized measuring system is designed for measure the static magnetic properties of the hard magnetic materials e.g. Alnico, ferrite, magnets based on cobalt alloy with rare-earth elements or Nd-Fe-B alloy. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter. MAG-ST100 system fulfill the requirements of IEC404-5 Standard.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
-
-
Product
Rubber Durometer, Rubber Hardness Tester
LX-A
-
Shenzhen Chuangxin Instruments Co., Ltd.
LX-A Shore A Rubber durometer is widely applied in the low and medium hardness plastic, all kinds of rubber, multi-dimensional fat, leather, wax etc. The product conforms to GB/T531-1999 any other related standard.
-
Product
Hardness & LSI Titration Kit
Ultrameter™ III 9PTKB
-
The Ultrameter III 9P™ AHL Titration Kit, is based on the tried and tested design of the Ultrameter II™. The 9P adds the ability to perform in-cell alkalinity and hardness titrations either as stand-alone measurements or as part of an LSI calculation. Alkalinity, hardness, pH and temperature values can be manipulated in the LSI calculator to predict the effect of changes on water balance. Measurements are extremely accurate. And the 9P is simple to operate and maintain.
-
Product
Full-Automatic Testing Machine for Hard Board Vehicles
U800HDIR
-
. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Optional laser marking5. Support SHOPFLOOR report output6. Optional BARCODE READER
-
Product
Motor Drive Control
-
Four motor speed drive control models ranging from a simple speed dial/display to complex machine/process synchronizers. Capable of many motor/machine control schemes, from open-loop master to closed-loop pulse-locked speed/event synchronized follower. Compatible with all motor speed drives of any size/power rating with an analog input (AC, AC Vector, DC and Servo)
-
Product
Rockwell Hardness Testers
-
Newage Testing Instruments, Inc.
Newage Testing Instruments offers a wide range of rugged, high precision Rockwell hardness testers and accessories.
-
Product
cPCI® Hard Metric Eurocard Plugbord
-
VECTOR Electronics and Technology, Inc.
Boards for 1mm and 2mm hard metric Eurocard plug-in application with option to mount 2mm hard metric connector on ends. Available with different circuit patterns for prototyping applications.
-
Product
Mini-Integrated Portable Hardness Tester
PHT-3300
-
The PHASE II portable hardness tester, Model No. PHT-3300 is an advanced integrated portable hardness tester distinguished by its very compact size, high accuracy, wide measuring range and simplicity of operation. It is suitable for testing the hardness of all metals and widely applied in many areas of industry.
-
Product
Digital Leeb Hardness Tester
TIME®5310
-
Beijing TIME High Technology Ltd.
TIME5310 is an advanced digital Leeb hardness tester developed with advanced micro electronic technology. It is loaded with all the features for metal hardness testing, such as probe auto recognition, large memory, USB output, removable printer, software, etc. The improved display makes it is much easier to read the values. TIME5310 digital hardness meter is a must have for testing in the field or in the lab. By the way, there are newly designed probes for this hardness meter now.
-
Product
Direct Drive Motors
-
The Javelin Series enables OEMs to design high performance, reliable, small and lightweight systems using flexible and easy-to-integrate linear motor components. The Javelin Series’ state-of-the art magnetic designs deliver high acceleration and high speeds in compact form factors. Direct drive technology and air core (ironless) construction provide good mechanical stiffness, low cogging and zero backlash, reducing settling times and increasing system performance and throughput.
-
Product
IQpump Drives
-
Our drives were designed with the pump service operators and pump system owners in mind and offer ease of setup and comprehensive pump and motor protection features.
-
Product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
-
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
Product
Hardness Testers
-
* Compact plastic case, suitable for use under poor working conditions. Test at any angle, even upside down.* Wide measuring range. It can measure the hardness of all metallic materials. Direct display of hardness scales HRB, HRC, HV, HB, HS, HL* Large screen (segment LCD), showing all functions and parameters. With EL background light.* Large capacity memory could store 100 groups information.* Datapro Software to connect with PC via RS232 port. Micro printer support* Software calibration function.
-
Product
Tablet Hardness Testers
-
Teledyne LABS offers both manual and automated tablet hardness testers. Tablet hardness testing is a method of determining mechanical properties of a drug product, typically oral dosage forms such as a solid dose tablet. Tablet breaking force (commonly called tablet hardness) is a crucial characteristic in the manufacture of solid dose formulations. Tablet hardness testing is a major step in tablet consistency and quality control.
