Wave Solder
-
Product
20-Pin GMCT Male Connector, 10A, Panel Mount, Solder Bucket
40-963-020-10A-M
-
The 40-963-020-10A-M connector is designed to allow users to directly terminate a cable with soldered connections. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. Included is the screwlocks/fixing screws and male solder bucket contacts.
-
Product
Acoustic Wave Device
-
Murata offers high-performance acoustic wave radio frequency (RF) devices including filters, duplexers, diplexers, resonators, and frequency control devices. This allows us to provide a wide range of acoustic wave-based RF devices in a one-stop service to all RF engineers.
-
Product
Profiling Current Meter and Wave
SeaGuardII DCP Wave
-
The SeaGuardII DCP Wave is a 600kHz Doppler Current Profiler able to measure directional wave parameters and currents from a bottom mounted installation.The Acoustic Wave software 5759 used by the DCPS implements unique features to improve the wave measurement accuracy by optimizing the signal to noise ratio.Maximum deployment depth is 40m in normal scatter conditions. The Profiling Current Meter and Waveis available as a self-recording instrument. It can be easily integrated into a real-time system offering reliable two-way communication.
-
Product
04 With Soldering Eyelets | 1 Wafer | 24 Positions
04-1xx3-00/30-xx
-
Very robust, multi wafer selector with 15° detent angle, switching torque up to 20 Ncm and a rotational life up to 25'000 cycles
-
Product
Plane Wave Converter
PWC200
-
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
Product
GENERAL INSPECTION MACHINE AFTER SOLDER MASK
-
DVI is a technology of automated optical inspection, which can inspect deep to the difference from semi-transparent layers or semi-reflective layers.
-
Product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
92-960-104-M
D-Sub Male Connector
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied without backshell. This connector is not compatible with Pickering modules that use the 104-pin D-type connector.
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5021
Amplifier
The HMMC-5021 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5021 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gain response and excellent port matches over the 2-22 GHz frequency range.
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5022
Amplifier
The HMMC-5022 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5022 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-22 GHz frequency range.
-
Product
2-26.5 GHz Traveling Wave Amplifier
1GG7-8045
Amplifier
The 1GG7-8045 is a broadband GaAs MMIC Traveling Wave Amplifier designed for high output power and moderate gain over the full 2 to 26.5 GHz frequency range. Seven MESFET cascode stages provide a flat gain response, making the 1GG7-8045 an ideal wideband power block. Ebeam lithography is used to produce gate lengths of ~0.3 mm. The 1GG7-8045 incorporates advanced MBE technology, TiPtAu gate metallization, silicon nitride passivation, and polyimide for scratch protection.
-
Product
37-Pin D-Type Female Solder Pin HV
92-960-037-F-HV
-
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Pulsed And CW ESR/EPR: Quasi-continuous Powerful Millimeter (mm-wave) And Sub-millimeter (sub-mm Wave) Orotron Generator
-
Insight Product Company offers Quasi-continuous powerful millimeter (mm-wave) and sub-millimeter (sub-mm wave) Orotron Generators which can be used for both continuous wave (CW) and pulsed electron spin resonance (ESR) and electon paramagnetic resonance (EPR) experiments.
-
Product
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178
610104142
Coax Contact (Receiver)
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178.
-
Product
Guided Wave Radar (GWR)
VEGAFLEX
-
In level measurement with guided wave radar, microwave pulses are conducted along a cable or rod probe and reflected by the product surface. The measuring probe of the TDR sensor ensures that the signal reaches the medium undisturbed. Liquids, bulk solids and separation layers (interfaces) in liquids are commonly measured with this measuring technique.
-
Product
Continuous Surface Current Mapping & Wave Monitoring System
SeaSonde
-
The SeaSonde HF radar system by CODAR Ocean Sensors is your solution for making continuous, wide-area ocean observations. The SeaSonde will provide you with years of real-time data over large coverage areas, with ranges up to 200 km — This is not possible with any other technology!
-
Product
Single Photon Detector System For Near-Infrared (1.6-2.3 Um Wavelength) Waves With Closed-Cyle Cooling
-
Single Photon Detector System for Near-Infrared (1.6-2.3 um wavelength) waves with Closed-Cylce (cryogen-free)cooling
-
Product
Solder Paste Inspection Machine
3D SPI
-
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
D-Sub Male Connector
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
Millimeter Wave Frequency Counter 70-170 GHz
-
Insight Product Co. offers the electronic frequency counter for frequency measurements of millimeter wave generators of continuous or pulsed signals. The counter has an auto and waiting modes of operation and a direct 6-digits reading in frequency range (70-170) GHz without an external mixer.
-
Product
Ring Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
Product
Combination Wave and EMC Surge Generators
-
Shanghai Guantu Technology Co., Ltd.
Surge generator is an electronic measuring instrument used in the fields of information science and system science, electronics and communication technology.
-
Product
Solder Cup Connector Kit
Y1142A
D-Sub Male Connector
Used to build custom cables for 34950A – 78-pin Dsub male – 60 V.
-
Product
Long Wave Infrared Cameras
Calibir DXM640 Series
-
The Calibir uncooled Long Wave Infrared camera platform offers outstanding shutterless imaging performance and is optimized for Size, Weight and Power (SWAP). The Calibir DXM640 series features both shutter and shutterless operation and rapid image output on power up while delivering uniform response over the entire operating temperature range, making it ideal for thermal imaging applications requiring uninterrupted image acquisition. ULIS’s gen2 sensor offers an improved NETD and the updated calibration include customized gain correction on a per lens basis to offer even better image performances and response uniformity.
-
Product
HD Arbitrary Waveform Generator,8 Ch,350 MHz,16 bit,128Mpts/Ch,6 Vpp output,AFG/AWG, Wave Sequencing
T3AWG3358
Arbitrary Waveform Generator
HD Arbitrary Waveform Generator,8 Ch,350 MHz,16 bit,128Mpts/Ch,6 Vpp output,AFG/AWG, Wave Sequencing.
-
Product
Soldering Stations
SM-878AD
-
*Module: 878AD*Display: LED*Power Rating:700W *Air Flow: 120L/Mints*Temperature: 100-450DEGREE*Noisy: <45dB
-
Product
Guided Wave Radar Level Transmitters
LWT Series
-
For high-accuracy, reliable measurements even in harsh conditions.Using radar frequencies, guided in a probe going into the monitored vessel, guided-wave radar level measurement provides continuous, reliable measurements with high accuracy. The radar wave being guided by the probe, the wave energy remains high which allows measurement even in harsh conditions.
-
Product
68-Pin SCSI Micro-D Female Solder Bucket
40-962-068-SB-F
-
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Soldering station
SM-850 with Hot Air
-
*Place of Origin: Guangdong, China (Mainland)*Brand Name: MCH*Model Number: SM-850*CONDITION: BRAND NEW
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
Wave Inverter - New Compact, High-performance Series
CSI 280-F3 Series
-
ABSOPULSE Electronics has released the CSI 280-F3 Series of ultra-compact, high-performance dc/ac sine wave inverters. The units introduce new semiconductor technology and a unique design topology that simplifies the circuitry and enables significantly more compact construction, lower weight and cost, and higher MTBF than previous 300VA inverter designs. The total footprint of each unit is 132 x 64 x 300 mm.
