3-D Solder Paste Inspection
checks form, height, surface area, bridges, volume, x/y offset and coplanarity of solder.
-
Product
3D Solder Paste Inspection Machine (3D-SPI)
3Si Series
-
Saki's 3D SPI identifies critical defects and assists with process improvement.
-
Product
3D Solder Paste Inspection system
PI Series
-
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
Product
3D Solder Paste Inspection (SPI)
-
Systems designed for solder paste inspection (SPI) quickly and reliably check the solder paste deposits on the circuit board.
-
Product
3D Solder Paste Inspection (SPI)
TR7007 SII
-
Offering inspection speeds of up to 200 cm2/sec, the TR7007 SII is the fastest solder paste inspection system in the industry. This highly accurate inline shadow-free solder paste inspection solution offers full 3D inspection at resolutions of 15 µm or 10 µm. Built on a high precision linear motor platform, the system's hallmark features include closed loop function, enhanced 2D imaging, auto-warp compensation and fringe pattern technology. Increase capacity without sacrificing additional space with an available dual-lane configuration.
-
Product
3D Solder Paste Inspection
aSPIre 3
-
Industry-leading measurement accuracy and inspection reliability- Perfect solution to eliminate shadow problems, base plane settings, and problems with projection direction- Full 3D foreign material inspection solution for the entire PCB- High productivity through the highest accuracy
-
Product
Tool, Inspection Depth Gauge, Mini Coax, ITA
910121157
Inspection Tool
Used to verify the depth setting of the center conductor of the ITA mini coax contacts.
-
Product
Tool, Inspection Depth Gauge, Micro Coax, Receiver
910121179
Inspection Tool
Tool, Inspection Depth Gauge, Micro Coax, Receiver
-
Product
Solder Paste Inspection System
LaserVision SP3D Mini
-
The LaserVision SP3D Mini offers the same level of overall measurement capabilities as the VisionPro SP3D. Utilizing a lower cost microscope platform and the ability for customers to supply their own PC if needed, the SP3D Mini sets the "affordable" boundary on reliable, low cost SPI solutions.
-
Product
Solder Paste Inspection Machine
3D SPI
-
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
Product
Solder Paste
MVP Versa (3D SPI)
-
The first part of any SMT process is Paste. MVPs Versa and 900 Series platforms provide high accuracy paste inspection. High accuracy paste measurements are made using a choice of 10um or 5um 3D measurement systems.
-
Product
Solder Paste Inspection
3D SPI
-
Checking all the relevant points in the production process is essential, especially in terms of analyzing the causes of defects, fixing them, and – most importantly – preventing them in the future. That’s why solder paste printing is of fundamental importance for manufacturing complex assemblies: If paste printing isn’t performed correctly, the defect can impact the subsequent assembly and the soldering process, resulting in a tilted component or a poor or missing solder joint.
-
Product
Tool, Solder Kit, Mini Coax with Solder Sleeve
910121144
Soldering Fixture
Used to solder Mini Coax Solder Sleeve contacts.
-
Product
Dual Projection 3D In-Line Solder Inspection System
KY8030-2
-
The new KY8030-2 delivers 2x fasterinspection without compromising performanceand accuracy.Using patented dual projection, the systemeliminates the critical Shadow problem thatall 3D SPI systems can be vulnerable to.Easy UI and SPC Plus are included in the systempackage in order to help users achieve faster& easier printer process optimization
-
Product
Dimensional Inspection (3D Inspection)
-
The 3D measurement data from our scanners and PCMMs offers a comprehensive definition of a physical object that is used for measurement, inspection, comparison and reporting. When a part is defined by millions of points, you can see subtle deviations, slight variations and fine details, which gives you the confidence that a part (or mold) meets your specifications. To deliver the best of both worlds, we combine 3D scanning with our contact, touch-probe measurement tools to deliver precise dimensions on geometric shapes.
-
Product
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA
910121178
Soldering Fixture
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA.
-
Product
Tool, Inspection Depth Gauge, Mini Coax, Receiver
910121156
Inspection Tool
Used to verify the depth setting of the center conductor of receiver mini coax contacts.
-
Product
Solder Paste Analysis
SPA1000
-
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
Product
Solder Past Inspection
-
From the innovative Z-Check 3D through to the entry level Z-Check 100 the entire range has been designed to provide accurate pad specific measurement of solder paste deposits, adhesives and component placement. Amongst its other features the Z check software comes with the convenience of a full SPC package as standard.
-
Product
High-speed 3D Solder Inspection Machine
YSi-SP
-
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
Product
Simple 3D Measurement & Inspection
XG-X Series Vision System
-
Abundant processing power is available even with multiple camera connections, including the 21 megapixel color camera, line scan cameras, or 3D cameras. XG-X Series offers high-speed, high-resolution cameras for high-accuracy inspection, providing powerful solutions for a variety of problems that arise in manufacturing.
-
Product
Solder Paste Printers
-
Shenzhen Leadsmt Technology Co.,Ltd
Is mainly used to print the solder paste to the circuit board, is one of the essential equipment in electronic manufacturing.
-
Product
High-speed In-Line 3D CT Inspection System
X-eye 6300
-
Automatically inspects the defects of products in customer's line with high-speed 3D CT tomography.Able to inspect every defects of Double-sided PCBA & BGA mounted components precisely by solving overlapped X-ray image issue.Inspection speed of 3 sec/1FOV from loading to automatic Good/NG judgement.
-
Product
3D X-ray hybrid inspection system
YSi-X
-
Ideal for 100% inspection of onboard automotive products and many other items by 3D X-rays acquire layered of target. X-ray, optical, infrared, and laser height measurement as standard equipment; hybrid and high reliability with multiple inspection modes.
-
Product
Solder Paste Inspection System
KY8030-3
-
The new KY8030-3 delivers 3x fasterinspection without compromisingperformance and accuracy.Using patented dual projection,the system eliminates the criticalShadow problem that all 3D SPI systemscan be vulnerable to.Additionally, the new KY8030-3 has solvedthe PCB Warp problem that seriouslyimpacts inspection accuracyand reliability of result.
-
Product
Solderability Tester
MUST 3
-
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
Product
Inspection System for high-power precise 3D X-ray CT
X-eye PCT225
-
Inspection System for 3D X-ray CT able to analyze defected area precisely by precise movement of axis with high polished Anti-vibration table. High-power X-ray Tube of max. 450kV and large area Flat Panel Detector of max.16 inches can be installed depending on the sample. Customized 3D CT equipment is available with selecting main parts by customers depends on their needs for size and material.
-
Product
Soldering Test
-
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
-
Product
3D Automated Optical Inspection Systems
New 3Di Series
-
To handle today’s rapidly changing market trends, the system can handle complex inspection challenges such as high component mounting density areas containing highly miniaturized parts placed near much larger and taller component. With our new 3D AOI system, you can strengthen quality assurance and increase production efficiency.
-
Product
3D Automated Optical Inspection System
EAGLE 3D 8800 SERIES
-
EAGELE 3D 8800 AOI applies 8-way projection for 3Dmeasurements to all models, minimizing shadow effectserrors and performing 100% 2D&3D examinations simultaneouslyin all FOV areas.
-
Product
3D Sensors
-
*Up to 38500 distance values per measurement for a detailed assessment of the application*Configurable outputs*Visual assessment of distance, level or volume*Predefined function blocks*Time-of-flight measurement principle
