Printed Circuit Assembly
Printed Circuit Board Assembly
-
product
Digital Circuit Breaker Analyzer
CT-3500 S2
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Towards Pin 1
A050DF5-C-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Portable Circuit Breaker Tester
PI-1600
The PI-1600 Circuit Breaker Tester incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-1600 test set is two testers in one, incorporating the PI-800 and PI-AUX. The PI-800 section can be used alone, on 120 or 240 VAC supplies, generating continuous current of 400, 800, amps at 4.2 kVA, with peak output to over 10x. When configured for the PI-1600, the PI-AUX output unit is connected in series or parallel to the PI-800. The PI-AUX boosts total power to 9.8KVA, and allows testing of draw-out breakers and MCB’s to 1600 Amps. The units are housed in rugged interlocking suitcase-size enclosures. Each piece weighs no more than 125 pounds, allowing one-person hand truck mobility. Basic operation is very simple, and the proven MAC-21 control instrumentation provides optimal output control and measurement. The MAC-21 instrumentation is supplied in a separate rugged portable case, interlocks on top of the PI-800, and connects to a cable in the rear of the test set.
-
product
75 Ohm BNC to BNC Cable Assembly
40-977-701-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Inspection of Glue Dot Assembly
ScanINSPECT's ADI
ScanINSPECT provides a simple and user-friendly alternative to inaccurate and time-consuming manual inspection methods or expensive, high-end AOI systems. ScanINSPECT uses a simple Windows user interface integrated with an automatic table and image-processing unit. This combination allows 100% inspection of adhesive placement on PCBs after dispensing.
-
product
7 Flat (Spade) Pin Trailer Circuit Tester
PT7893
Easily test trailer plug circuitry on most new light trucks, SUV's and RV's. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Unterminated (Tinned Ends), 0.5m
40-972B-200-0.5m-MU
This male rear exit to unterminated 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to the product by screwlocks.
-
product
Short Circuit Test System
Shanghai Guantu Technology Co., Ltd.
The short-circuit test system refers to what kind of short-circuit test is carried out by which equipment, and how long is the test time. But I have one thing to tell you, the short circuit test is a kind of destructive test, mainly to test the working condition of the used equipment in a crisis situation, or to test how strong the anti-destructive ability of the used equipment is. Just like a lot of equipment in the military must undergo a short-circuit test, some for 3 minutes or longer, in order to resist breaking calls against the enemy during wartime.
-
product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Tinned Ends, 2m
A009DF4-T-0A200
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire.The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match theconnector pin designation.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 0.5m, 500 Port
A500RMR-T-0A050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products). Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A037DM5-T-0A100
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Tinned Ends, 5A, 0.5m
A050FFR-T-0A050
This is a 0.5m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP+
SCOT MXP+ measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time of 2 Main + 2 PIR contacts per pole, 3 poles simultaneously, ensuring measurement of 6 Main + 6 PIR contacts simultaneously. Ideally suitable for CBs having PIR contacts & multiple breaks per pole
-
product
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin FML D-Sub
540112020140
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin FML D-Sub.
-
product
Assembly
Leverage ARC to Complete Your Next Complex Board and Cable Assemblies ProjectARC has the ability to build up CCAs, install components at the module level and build up sophisticated wiring and cable assemblies. We know what it takes, because we use this for our own manufacturing for complex, high-mix product builds.
-
product
Circuit Breaker Identifiers
191 CBI
Standard Electric Works Co., Ltd
● 191 CBI is an easy tool to find the circuit breaker or fuse supplying electrical power to an outlet or lighting fixture. Just plug the transmitter into the outlet.● Use the receiver to scan the circuit breaker panel box. An audible tone will be clearly heard when the right circuit breaker is scanned.● The plug of transmitter is changeable. The plug of transmitter could be changed for customers' requirement from different countries.
-
product
Integrated Assemblies
Teledyne RF & Microwave offers full first-level integration capabilities, providing not just performance components but also full subsystem solutions to help reduce program schedule and cost. Drawing on our expanding breadth of components, Teledyne delivers customer-specified subsystems of analog and mixed analog-digital design, including hybrid, MMIC, and mixed hybrid-MMIC configurations. Designed to meet military or space applications, some typical subsystems Teledyne delivers include I/Q demodulators, coupled detector assemblies, switched amplifier detector assemblies, and dual-band VCOs.
-
product
Cable Assembly, Receiver, QuadraPaddle, 72", 2 RJ45 Plugs
540224010540
Cable Assembly, Receiver, QuadraPaddle, 72", 2 RJ45 Plugs
-
product
High-power Laser Diode Assembly
The laser diode is one of the most common devices used throughout photonics. The micro-assembly process calls for the placement and bonding (align-&-attach) of single emitters, or multiple laser diodes (stacked or complete bars), the placement, active alignment and bonding of necessary micro-optical elements, subsequent device testing, and ultimately packaging and quality control. ficonTEC’s machine systems are capable of all the steps necessary for assembling laser diodes, even high-power devices. Multiple in-line systems can be configured to address entire process segments.
-
product
50Ω UWave SMA 2.92 Cable Assembly, 40GHz, 0.25m
40-977-544-0.25m
50 Ohm uWave SMA 2.92 Plug to uWave SMA 2.92 Plug Cable Assy, 0.25m Long.
-
-
product
Cable Assembly, 50-Pin D-Type, Female To Unterminated With Ferrules, 2m HV, Exit Away From Pin 1
40-972-050-2m-FU-HV
50-Pin Female to Unterminated D-Type Cable Assembly, High Voltage, With Ferrules, 2m Long, 45º Cable Exit Away From Pin 1.
-
-
product
Handheld Circuit Breaker And Timer Analyser
CAT-H Series
The operation of the breaker can be initiated in different ways (e.g. from a control room, by a local breaker or externally by a test device) depending on the test conditions. Various time measurement triggers are available to record a measurement under a different test condition:*Coil control channel*Continuous current clamping channel*DC voltage channel
-
-
-
-
-
product
ELECTRONIC CIRCUIT TRACER
PPECT3000
*Locate short and open circuits without having to remove plastic panels, molding and carpet*Traces shorts and open wires with visual navigation and sound indicators*Pinpoint shorts, open circuits, switches and breaks in wires
