PXI Backplanes
-
Product
PXI Monitored Multiplexer, Single 128-Channel, 1-Pole
40-619-401
Multiplexer Module
The 40-619-401 is a high density PXI 2 A multiplexer module in single 128-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
PXI Solid State Very High Density Matrix
40-500-001
Matrix Switch Module
A very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high currents and voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Switch Module
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
PXI Platform Completion Hardware
Platform
PXI Platform Completion Hardware enhances your PXI test systems. These products can monitor the health of a chassis, improve device synchronization, share data between systems, add data storage, and more.
-
Product
PXI Single Transfer Switch 18GHz 50Ω SMA
40-782-521
Switch Module
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
PXI Single 24x8 Matrix, 1 Pole Switching
40-521-021
Matrix Switch Module
An ultra high density matrix module is configured as a 24x8, this range is availablein a choice of reed relay formats: 1-pole (shown here), 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisitionsystems. These PXI matrix cards are constructed using high reliability RutheniumElectro-Plated Reed Relays, offering >10e8 operations to give maximum switchingconfidence with long life and stable contact resistance.
-
Product
PXI Multiplexer, 16-Bank, 5-Channel, 1-Pole
40-616A-021-16/5/1
Multiplexer Module
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module is part of our range of reed-relay based switching solutions. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously.
-
Product
PXI High Density Multiplexer, 2-Bank, 40-Channel, 2-Pole
40-615A-010
Multiplexer Module
The 40-615A-010 is a 2-bank, 40-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI Single 8 Channel Optic Mux FC/APC
40-852-018
-
The 40-852-018 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Dual 16x6 1-Pole High-Density PXI Matrix Module
40-520-303
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Triple SP6T Multiplexer 40GHz 50 SMA-2.9
40-784A-043
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI Waveform Generator
Waveform Generator
PXI Waveform Generators can produce precise waveforms including sine, square, triangle, and ramp as well as arbitrary, user-defined waveforms using sequences of data or streaming continuously from a host or peer-to-peer instrument within the PXI system. These instruments are ideal for tightly synchronized, mixed-signal test systems in scientific research or test of semiconductor devices, consumer electronics, automotive, and aerospace/defense.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 22.3M
40-297-154
Programmable Resistor Modules
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Thermocouple Simulators
-
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
Product
PXI Dual 12x8 Matrix, 2 Pole Switching
40-522-022
Matrix Switch Module
Medium density PXI dual 12x8, 2-pole matrix - it is also available in reed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
PXI Very High Density Multiplexer, 5-Channel 16-pole
40-670C-021-5/16
Multiplexer Module
The 40-670C-021-5/16 is a 5-channel, 16-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI Electronic Load Module
Load Module
PXI Electronic Load Module provides the electronic load capabilities of sinking DC power with high-accuracy measurements in a compact form factor optimized for design validation, characterization, and production test.
-
Product
PXI High Density MUX BRIC, 8-Chan, 40-Pole
40-570-212
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Dual 3-ADC PXI Express Hybrid Module
SMT702
-
Sundance Multiprocessor Technology Ltd.
The SMT702 is a PXI Express (opt. Hybrid) Peripheral Module (3U), which integrates two fast 8-bit ADCs, a clock circuitry, 2 banks of 1GByte DDR2 Memory each and a Xilinx Virtex5 FPGA, under the 3U format.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
Programmable Resistor PXI Board
GX1164 Series
Programmable Resistor Modules
The GX1164 is a 3U PXI programmable resistor module with 4 channels of 16 resistors each or 8 channels of 8 resistors each. The module is available in various resistance ranges and resolutions.
-
Product
PXI Multiplexer Dual 24 Ch 1 Pole
40-632-021-D/24/1
Multiplexer Module
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
Product
PXI Replacement Microwave Multiplexer Relay
40-785-751-R
Multiplexer Module
Pickering Interfaces PXI Microwave multiplexer modules are suitable for switching 50Ω signals up to 40GHz. The 40-785 is available as a single or dual 6 channel multiplexer, with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI-5105, 60 MHz, 8-Channel, 12-Bit PXI Oscilloscope
779685-02
Oscilloscope
60 MHz, 8-Channel, 12-Bit PXI Oscilloscope—The PXI‑5105 high-density PXI oscilloscope device has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth. The PXI‑5105 also features PXI synchronization and data streaming capabilities.
-
Product
PXI Precision Programmable Resistor Modules
-
Pickering's PXI precision programmable resistor modules feature high setting resolution with excellent stability and accuracy through the use of innovative switching networks and software correction techniques. This also means all resistance values can be set - there are no missing values due to switch resistance or resistor tolerance. These modules are ideal for sensor emulation applications that require very fine adjustment and also have the capability of being set as open or short circuit to simulate faults in cabling systems. The range includes modules specifically designed for RTD and strain gauge simulation.
-
Product
PXI 4x4 10GHz Matrix with Termination
40-787-518-4X4-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module
-
Product
PXI 3A Power MUX BRIC, 6-Channel, 48-Pole
40-571-006
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
20-slot ATX-supported Bridged PICMG Bus Active Backplane
ATX6022/20GP18
-
*1 PICMG, 18 PCI and 1 ISA*Compatible with AX61492 chassis*Supports both AT and ATX power supply
-
Product
Multi-Function PXI Card
GX3788
Digital / Analog Converter
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
Product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
-
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
