-
product
Isolators & Circulators
Smiths Interconnect's Isolators and Circulators set the industry benchmark for low loss and high power performance in the most stringent Military and Space environments.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
product
Circbord
8023
VECTOR Electronics and Technology, Inc.
3-hole solder pad for interconnecting multiple component leads. I/O area with square solder pads for connectors mounting. Circuit pattern etched onto both sides. Double sided with plated thru holes. Solder mount DIP sockets or IC devices with any lead spacing.
-
product
DSP And Power Amplifier
DMPA12
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
-
product
Voltage Controlled Oscillators
Mercury Systems’ VCOs (Voltage Controlled Oscillators) offer predictable consistency, rugged design and reliable performance. Our VCO products will meet your application’s most demanding stability and low phase noise requirements; featuring wide tuning bandwidth up to an octave. With custom designs and space qualified versions, trust Mercury to provide the VCOs for your next design.
-
product
Liquid Sensors
Panasonic Industrial Devices Sales Company of America
These compact Liquid Sensors detect small leaks, liquid and air bubbles in small tubes and determine liquid levels. Using a capillary effect, the EX-F70/F60 Sensor Series delivers high speed detection of small leaks with a 50 ms response time, with highly chemical resistant and space saving models.
-
product
Vertical Hinged Mounting Frame, ICon, 5U, 3 Positions
310113463
The 5U Vertical hinged Mounting Frame mounts to standard 19" racks and hinges open to allow access to wiring between the instruments and VPC Receiver. The 3 cutouts are spaced evenly across the panel. iCon cover plate sold separately (310 113 467).
-
product
Ion & Electron Detection
Photonis is the global leader in the development and manufacturing of detectors and optical components to detect ions and electrons. These detectors and components have been designed for a wide range of scientific instruments used in space and research projects but also in cells and material analysis in lifescience or non destructive testing.
-
product
Programmable Multifunction Counter Board, Isolated, With 4 Function Modules
CPCI-1710
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
product
3GHz 16-Channel Signal Generator 19" 3U Rack Module
LS30816R
The LS30816R, 3GHz 16 channel RF Analog Signal Generator, offers industry leading performance, in a 3U, 19” space efficient, rack-mounted box. The LS30816R features 16 phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. With the highest channel density in the market the LS30816R offer the ideal solution for applications requiring high channel count at minimum space and cost.
-
product
Plugbord
3682-2
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience.Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
product
Automotive Rotary Potentiometers
Panasonic Industrial Devices Sales Company of America
Panasonic Center Space Rotary Potentiometers offer built-in LED options and automotive operating temperatures. Target markets include Automotive and Measurement Equipment.
-
product
Recess Mount Adapter Kit For M9018B And M9019A
Y1216B
The Y1216B is a complete rack-mounting kit for the M9018B and M9019A PXIe chassis. It includes rack flanges, handles, and attachment hardware. Y1216B suspends the chassis in a Keysight rack using only 4U of rack space. It also recesses the chassis by 4 inches. This kit is not compatible with the Y1270A Front Panel Interfacing Kit.
-
product
Temperature Forcing System
ETF-SERIES
Precise Temperature Accuracies with Reliable Test Results Temperature Limits: -40/-60 °C to 30 °C Temperature Accuracies: ±2-3°C Temperature Rate of Change: 20-25 deg /min (Non-linear) Maintenance Free Access to The System Self-Sufficient System Compact with small footprints suitable for any space constraint laboratories Low decibel system Suitable for testing electronic chips / devices Environmentally friendly refrigerants Efficient heating Microprocessor based single set point PID temperature controller with data logging Flexible hose up to 2.5-3.0m Interchangeable heads according to chip size. Inbuilt electrical control panel with switchgear system
-
product
CGH & CGH+SNP Microarray Scanners & Equipment
Learn about our selection of CGH & CGH+SNP Microarray Scanners & Equipment for your research and diagnostic workflows. It includes the SureScan Microarray Scanner, the G2565 Series Microarray Scanner accessories and SureScan Scanner accessories including backing slides, hybridization chamber, microarray hybridization oven, hybridization oven accessories, and stabilization & drying solution. The SureScan Microarray Scanner is the foundation of our complete microarray solution that offers outstanding sensitivity and resolution, delivering flexibility to analyze genomics and cytogenetics microarrays. The small footprint of the SureScan Microarray Scanner allows lab space to be optimized while improving the sensitivity and maintaining the broadest dynamic range. Read on to find more about our microarray scanners.
-
product
Envelope/Peak Detectors
Analog Devices envelope/peak detector products provide a versatile solution with state-of-the-art accuracy for communications, space, military, and other markets. Members of this portfolio offer high rms accuracy and fast envelope response, while operating in multiple temperature ranges to suit commercial and industrial needs.
-
product
Variable Power Supply
VS-10a
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
product
370MHz To 4GHz Radiation Measurement System
RMS-0440
The MegiQ Radiation Measurement System (RMS) is a compact test system that performs 3-axis radiation pattern measurement in non-anechoic spaces.
-
product
6TL23 Off-Line Seat Operation Base Test Platform
H71002300
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
-
product
Light Section Sensors
Leuze electronic GmbH + Co. KG
Switching light section sensors are designed to perform scanning, two-dimensional object detection along a laser line. They are especially well suited for completeness monitoring or product monitoring in the case of multiple track transport. The short measurement time and the detection range from 200 to 800 mm enable an inspection of the content at a high throughput rate even with deep containers. The internal data processing offers programming and differentiation of 16 different object types, thereby conserving control capacity. Complex detection tasks can be solved with one sensor. The compact housing ensures high flexibility during installation and saves installation space.
-
product
Rogowski AC Current Probe,30 MHz, 600 A
N7041A
The Keysight N7041A Rogowski coil current probe measures AC currents up to 600 A, with bandwidth ranging from 12 Hz to 30 MHz. The probe has a thin, lightweight, flexible, and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult-to-reach parts and confined spaces of a circuit under test. It can also measure large AC current without an increase in transducer size.
-
product
Signal Analysis
Wavelet Analysis
Wavelet analysis is perfect for presenting non-stationary signals, the properties of which change in time or space, and it is also a powerful tool for system dynamics analysis.
-
product
Embedded Vision
In the industrial environment, especially in digitalized, automated production scenarios, more and more so-called embedded systems are being used. Embedded devices are small, with compact dimensions, highly efficient, and generate little waste heat. Therefore, they are also suitable for limited space conditions. Due to often harsh environmental conditions, they must be particularly robust and resistant to external influences like massive dust accumulation, strong vibrations, and high humidity or even direct contact with water. Typically, embedded devices are handhelds, smartphones, tablets, vision sensors, smart cameras, smart sensors and single board computers. If the systems have integrated machine vision software, they can be used for a wide range of image processing applications. This is known as embedded vision.
-
product
Rack Mount Kit For N8900 Autoranging System DC Power Supplies
N8958A
The N8958A is a rack mount kit that provides all the necessary hardware to rack mount one N8900 Autoranging System DC Power Supply (any of the 28 models) in only 3U of rack space when installing in a Keysight rack.
-
product
Micro ATX Motherboard
Axiomtek's high performance Micro ATX motherboards (244 x 244 mm) support a wide range of computing capacities, rich I/Os and expansion slots. The Micro ATX motherboards are suited for space and cost sensitive applications.
-
product
Voltammetry/CVS
Professional VA/CVS instruments
Our Professional range of voltammetry and CVS systems contains a wealth of functionality on a small space: voltammetric trace analysis of metal ions and other substances and determination of organic additives in electroplating baths with cyclic voltammetric stripping.
-
product
Solution for High Density I/O Applications
BitBox
The BitBox is BitFlow''s new solution for high density I/O applications. Many machine makers require a large number of computer managed I/O signals for continuous control of the system state. This means controlling devices such strobes, solenoids, actuators, indicators etc. as well as gathering inputs from photo-detectors, switches, encoders and triggers. In general, BitFlow frame grabbers come with a fairly large number of inputs and outputs, but for some system this is simply not enough. Most customers end up purchasing another device to manage the I/O, which adds expense, requires another slot, another driver and SDK, another manual, etc. The BitBox has been designed for just this situation. It is controlled completely from the frame grabber, uses the same API, driver and manuals as the frame grabber. This saves time, money, space, and learning curve.
-
product
Rack Mount MW Signal Generators
The Rack Mount platform of the Lucid signal generator is designed to offer maximum channel density at minimum cost of space. Offering up to 4 phase coherent channels in a 19” 1U box, the rack mount platform is by far the best in its class for signal density. Featuring fast switching speed, superior signal integrity and purity, removable memory card for maximum security, all the necessary modulated signals for analog communication systems, built in LAN and USB interfaces, this platform meets today’s most demanding specifications, needed for ATE and production lines.
-
product
Leeb Hardness Tester
HT6561
Product synopsis1.1 Typical Applications* Die cavity of molds* Inspection of bearing and other mass produced parts on aproduction line* Failure analysis of pressure vessel, steam generator andother equipment* Inspection of installed machinery, permanent parts ofassembled systems and heavy work pieces.* Testing surface of a small hollow space* Material identification in the warehouse of metallic materials* Rapid testing in large range and multi-measuring areas forlarge-scale work piece1.2 Testing Features* Palm size for narrow space.* Test at any angle, even upside down.* Direct display of hardness scales HRB, HRC, HV, HB, HS,HL.* Large memory could store 250 groups including singlemeasured value, impact direction, material and hardnessscale etc.* User recalibration function allowed.* Can communicate with PC computer for statistics andprinting by the optional cable.* Manual or automatic shut down.* Low battery indication.1.3 Technical SpecificationsDisplay: 12.5mm LCD with back lightAccuracy: Display error ±0.8% at LD=900Measuring range: 200-900LConversion: HL-HRC-HRB-HB-HV-HSDMaterials: 9 different common materialsWith RS232C interfaceMemory: 250 data can be stored and re-readableImpact device: D Will handle the majority of hardness testingapplications. Weight: 75gPower supply: 2x1.5V AAA size batteryDimension: 146×65×36mmWeight: 130g (not including batteries)Working temperature： - 10℃～＋50℃Storage temperature：- 30℃～＋
-
product
Polyurethane Jacket RF Cable Assemblies
For applications where space is limited and minimizing transferred mechanical stress on the interface connection is a must...The polyurethane jacketed versions of our already proven cable assemblies deliver new engineering options to standard FEP jacketed cables.Polyurethane offers greater memory retention than a similar size cable jacketed with FEP. This feature offers the benefit of minimizing stress and torque applied to interface connections, such as those on a circuit board.It also allows cable to better maintain position in an installation where the "spring back" of an FEP jacketed cable could be problematic.Additionally, a polyurethane jacket offers improved abrasion resistance over an FEP jacket.
