Filter Results By:
Products
Applications
Manufacturers
Frequency Standards
Devices that produce a known frequency.
See Also: Hydrogen Frequency Standards, Rubidium Standards, GPS Clocks
-
product
Standard 4.47 (127.00) - 12.00 (340.00) High Frequency Probe
K-50H-S
Current Rating (Amps): 6Bandwidth @ -1dB (GHz): 4.00Return Loss @ -20dB (GHz): 2.50Nominal Impedance (Ohms): 50Test Center (mil): 600Test Center (mm): 15.24Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 90Recommended Travel (mm): 2.29Overall Length (mil): 1,205Overall Length (mm): 30.61
-
product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP022-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
Standard 6.20 (175.20) - 8.00 (226.80) High Frequency Probe
CSP-40A-015
Bandwidth @ -1dB (GHz): 6.00Return Loss @ -20dB (GHz): 2.30Nominal Impedance (Ohms): 50Dielectric VTE Rating (k VAC): 1Test Center (mil): 250Test Center (mm): 6.35Full Travel (mil): 200Full Travel (mm): 5.08Recommended Travel (mil): 133Recommended Travel Remark: Shield: 211 (5.36) including travel of probesOverall Length (mil): 1,231Overall Length (mm): 31.28Full Travel Remark: Shield: 275 (6.99) including travel of probes
-
product
Suitable For Frequency And Pulse Sensors
SEM1600F
The SEM1600F is a cost effective “smart” powered conditioner that accepts all common process pulse signals with a frequency range between (0.01 to 65000) Hz in standard configuration and (DC to 1000) Hz in counter mode. Typical applications would be to measure flow or batch counting.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
product
Frequency Synthesizers 0.050 GHz - 33 GHz
With standard designs covering 250 MHz to 20 GHz, Micro Lambda Wireless is the industry leader in YIG-tuned frequency synthesizers. From low cost single loop designs, to wideband configurations that outperform some test equipment, Micro Lambda is your full service designer and supplier of microwave YIG synthesizers.
-
product
PXI Three Channel Function Generator
Our PXI Function Generator is capable of generating sine, square and triangle waveforms to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. It can generate fast swept frequency signals, permitting the output to emulate the operation of variable speed devices. The module can also generate arbitrary waveforms loaded into its internal 256k memory, allowing the emulation of many waveform types including the typical waveforms of automotive and aerospace sensors.
-
product
1.533 Μm Frequency-Locked Laser
Thorlabs' LLD1530 Frequency-Locked Laser is a narrow linewidth, DFB-laser-diode-based, turnkey system with a vacuum emission wavelength of 1532.8323 nm and a high SMSR of at least 35 dB. The laser frequency is actively stabilized to a National Institute of Standards and Technology (NIST)-traceable molecular transition of acetylene and has an absolute accuracy at start-up that is better than ±25 MHz. The emission frequency immediately after start-up is then maintained with a ±25 MHz stability, providing an overall frequency accuracy of ±50 MHz. The LLD1530 is an accurate frequency reference designed to provide low-noise laser emission with excellent frequency stability, accuracy, and precision immediately at start-up. This source is ideal for use in demanding FTIR instrumentation, instrument calibration, gas sensing, and coherent telecommunications applications.
-
product
Log Periodic Dipole Array
ALP500
Standard remote antenna ideal for fixed applications. The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth.
-
product
Sound Level Meter & Real-time Analyzer
824
The Larson Davis System 824 combines advanced sound level meter and real-time analyzer capabilities into a rugged, user-friendly, ergonomic package. The base unit is an Integrating Sound Level Meter (ISM) that meets Type 1 Standards and offers simultaneous measurement of sound pressure levels using fast, slow, and impulse detectors, for A, C, and flat frequency weightings. This feature, termed ANY LEVEL™ measures 48 sound pressure parameters at once with a linear, 105 dB range. With firmware enhancements, the base unit expands as needed to accommodate multiple data processing requirements
-
product
Universal Frequency Counters
GT210PXI-2
GuideTech’s GT210PXI-2 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system with optimal cost. The ability to precisely resolve frequency and time yields both increased accuracy as well as reduced measurement time.
-
product
Frequency Expansion Modules
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
product
SMP Connectors
Pasternack SMP connector (sub-miniature push-on connectors) category contains mostly RoHS and REACH compliant product varieties. The SMP connector category includes dozens of configurations including coaxial sub-miniature push-on connectors, PCB mounted, non-sealed and hermetically sealed terminals and shrouds. Our subminiature push-on SMP connectors are built to precise microwave and RF industry specifications and are part of over 40,000 in-stock RF products. Connectors in SMP series from Pasternack are manufactured in male or female gender with a 50 Ohm impedance. Pasternack's SMP subminiature connector are available in straight or right angle versions as well as bulkhead or mount-less options. These connector designs include solder or solder/solder attachment methods. Pasternack’s SMP connectors are miniaturized push-on interconnects commonly used in high density, blind-mate systems that can operate up to 40 GHz. Standard sub-miniature push on connector items are offered in a high frequency 40 GHz version as well as a low frequency 8 GHz version and are also available in smooth bore, limited detent and full detent styles. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMP connector series is in-stock. Not just in stock, these subminiature push on connectors will also ship the same day as they are purchased.
-
product
Low Noise Triple Band Voltage Controlled Oscillator
This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.
-
product
Full Band Noise Figure and Gain Test Extenders
STG-06-S1
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC series), which consists of a Faraday isolator (STF series), full band mixer (SFB series), frequency multiplier, and IF amplifier. A frequency source with an output signal in the frequency range of 10 to 20 GHz is required as a local oscillator for the down converter. The noise source is automatically powered on and off by the noise figure meter.
-
product
Dual Channel Digital Receiver
MS 1740
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
product
High Power LED Aging Tester
LS600
• The standard LS600 has 1 Group which has 8 channels. That means LS600 can test 8 LEDs separately at one time. (Optional: it expand to 8 Groups which can test 64 LEDs separately at one time) • Aging Functions: Constant Current, Impact Pulse, On/Off Mode • Output current: 1~1000mA (Special Order Available) • Output voltage: 5V(Special Order Available) • Output frequency: 1~3000Hz, Duty Ratio: 1%-99% • Range of on-off circle: 0~9999h/59m/59s
-
product
Room Acoustics Analysis on iOS
RoomScope
RoomScope turns your iPad, iPhone, or iPod touch into a room acoustics measurement and analysis tool. With RoomScope, you can measure a room impulse response and then calculate reverberation time, early decay time, clarity, and definition, as defined in the ISO 3382 standard. RoomScope also allows you to adjust the Schroeder decay curve integration limits with the touch of your finger and plot the calculated room parameters versus whole or 1/3-octave band center frequency.
-
product
Calibration
RF Test Equipment
We calibrate following types of RF test equipment:EMF test systems (frequency selective)EMF test systems (broadband)Field strength transfer standards (e.g. RefRad)Line Impedance Stabilisation Network (LISN)Cable, attenuator, couplerAntennaField Probe
-
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Coaxial Calibration Kits
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger offers the following types of calibration kits with a range of coaxial connector series for vector network analyzers (VNAs). All Rosenberger calibration kits can be used from DC to their maximum frequency. Full version with adaptors and sliding loads for variable measurements Industrial version for standard measurements LRL and TRL version
-
product
Comb Generator, 10 MHz To 110 GHz
U9391M
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
High-Speed Clocking Module
FMC407
Sundance Multiprocessor Technology Ltd.
The FMC407 is a low-noise clock generation and distribution module with eight clock outputs and eight trigger outputs that are fully synchronized. This module can either distribute an externally supplied or a locally generated clock. In the standard configuration, the FMC407 can generate any clock frequency between 34.375 MHZ and 4.4GHz and lock it to an internal or external reference.
-
product
Standard Gain Horn Conical Lens antennas
Elva’s SLHA series of standard gain horn lens antennas cover the frequency range of 18 to 220 GHz in ten waveguide bands. They can be issued with rectangular or circular waveguide. Lens technology significantly allows decreasing mechanical sizes of horns and correcting beam for the best performance. These horns are ideal solution for measurement gain of other antennas, short range radars and radiometers.
-
product
Radio Frequency Cable Tester
RFCT
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
product
PXI Three Channel Function Generator
41-620-003
The 41-620 is a compact 3 channel function generator provided in a PXI 3U single slot module. It is capable of generating sine waves to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. The 41-620 can generate arbitrary waveforms loaded into the internal 256k memory, allowing the function generator to emulate many waveform types, including the typical waveforms of automotive and aerospace sensors.
-
product
Digital Line Tracer
TW-82P
Digital Line Tracer now with Passive Power Detection setting a NEW standard in High Frequency Line Tracing. The TW-82P Digital Line Tracer inlcudes a rugged contruction and compliant with IP65 standard. The casing is impact resistant and weatherproof ensuring you're ready for any conditions.
-
product
EMC Test Equipment
TDEMI eXtreme series
Highest measurement speed. Highest accuracy. Incredible dynamic. New operation modes. The novel product line TDEMI eXtreme (TDEMI X) is the latest and most advanced level of full digital measurement equipment for emission testing on the fast lane. It is based on the unrivaled and patented TDEMI® real-time technology of GAUSS INSTRUMENTS. It is easy and efficient in upgrading its frequency range by a various number of extensions which can be integrated into the instrument step by step. The frequency ranges are 1 GHz, 3 GHz, 6 GHz, 18 GHz, 26.5 GHz or 40 GHz respectively. A large variety of configuration possibilities makes the TDEMI X to the customized solution perfect fitting into your lab and to your application according to civil standards (e. g. CISPR, EN, FCC Part 15, ANSI C63.2, ANSI C63.4), military standards (e. g. MIL-461G, but also its previous versions and revisions) as well as avionic standards (e. g. DO-160). The frequency range of the TDEMI X instruments starts at 9 kHz in its standard configuration and can be extended down to 10 Hz by the option MIL/DO-UG or even down to DC by the available option OSC-UG as well. Like all other TDEMI measurement systems, the TDEMI X measurement systems can be remotely controlled and fully automated via Ethernet (TCP/IP) very easily.
-
product
Microwave Power Amplifier 10W 100 MHz to 20 GHz
GT-1000B
The Spanawave GT-1000B Microwave Power Amplifier offers linear high-power amplification across multi-octave bands. It is ideal for testing in EMC, wireless communications applications and Defense EW systems. For EMI/EMC and standards laboratories, the GT-1000B with 100 MHz to 20 GHz frequency range allows broadband testing without band switching or swapping narrow band amplifiers resulting in faster and more accurate testing.
