-
Product
ARINC825 (CAN Bus) Test & Simulation Module for CPCI With 2 Or 4 CAN Bus Nodes
ACC825-3U-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Dual Channel Dynamic Data Simulator
LS-77-SS
-
The Lumistar LS-77-SS PCI Dual Dynamic Data Simulator with optional bit synchronizer allows two command simulators one bit synchronizer, and a time code reader/generator in a single short PCI board. The two Command Data Simulators and Time Code Reader/Generator are implemented in FPGA using a next generation design based on the LS-70-P. The optional bit synchronizer is achieved using the Lumistar LS-40-DB low-profiledaughterboard.
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
Compact Hydraulic Vibrator Force Simulator
JF Series
-
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
-
Product
IBP Simulator
IBPS 2.0
-
The IBPS 2.0 is a PC controlled simulator to replace real IBP sensors. Originally designed for IEC 60601-2-34 testing, it can also be used by manufacturers to play their own test signals or database recordings.
-
Product
AIT PXI Express Test & Simulation Instruments
-
Avionics Interface Technologies
AIT’s Test & Simulation Instruments for MIL-STD-1553, ARINC 429, ARINC 664/Avionics Ethernet, and Fibre Channel are available in PXI and PXI Express form factors and are supported by software drivers for Windows, Linux, and LabVIEW Real Time. All instruments are also supported by Software Development Kits which provide API’s for C/C++, C#, and LabVIEW.
-
Product
Multi-Protocol Test & Simulation Adapter for USB or Ethernet
EXC-UNET2/xx
-
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
Fiber Optic Network Simulators
SIM-2FON-25
-
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types.This product is ideal for latency testing, product development and training and educational needs.
-
Product
Single Stream STANAG3910 Electrical Test & Simulation Module For 3U PXI Express/Compact PCI Express
ACE3910-3U-1-EN
Simulator
Single Stream STANAG3910 Test and Simulation module – Rafale – for PXI Express/Compact PXI Express with 1 dual redundant HS/LS channel and onboard Electrical Front End (EFE).
-
Product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
-
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
Product
Manikins for realistic simulation of the acoustic properties of a human
Head & Torso Simulators
-
If you need to carry out realistic in-situ measurements of headphones, telephones or hearing aids, you need a Head and Torso Simulator such as the B&K ‘HATS’ – Type 4128D or GRAS’ Kemar to complete your test setup. These manikins have built-in ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. They are commonly used for tests on telephone handsets, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. Please contact your sales engineer or email sales@listeninc.com for more information.
-
Product
EFT/Burst Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
Product
Hot Dipping Simulator
HDPS
-
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
Product
Wavefront Modeling And Simulation
-
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
Product
Measurement & Simulation
-
Highland Technology offers a wide array of tools for measurement, simulation, and control. Tachometers, thermocouples, RTDs, precision voltages, current loops, strain gauges, and more can be measured or simulated by Highland's products.
-
Product
Molding Simulation Software
Moldflow®
-
Engineers and analysts use Moldflow software for plastic injection molding simulation to improve plastic part designs, injection mold designs, and manufacturing processes.
-
Product
Battery Cell Simulation / Emulation
BMS
-
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
Product
Diagnostic Simulation
Stage
-
STAGE simulates aspects of Diagnostic, PHM and ISHM Engineering, showing the support capabilities of a System during its useful lifetime. Many types of analysis can be performed on STAGE, including Testability, System Reliability & Mission Success, Sustainability, and Logistics Resource Allocations.
-
Product
Electronic Warfare MMI and HMI Simulators
MS 1600
-
The EW IFU (Electronic Warfare Interface Unit) interfaces between Cockpit electronics viz., RWR Display Unit (DU), New control Box (NCB), CMDS Control/Display units and Simulator Host Computer (HOST). The EW IFU transmits the status of the cockpit control units to the host, receives display data from the host and transfers the same to RWR DU, NCB and CMDS CCU/CDU. The display data for the RWR DU received from the host would comprise of the complete symbol data in respect of emitters that are to be displayed based on the data from the Instructor Station (IS) and control input from the cockpit. The display unit receives and presents the data as symbology on the display screen. The EW IFU based on the PC–AT.
-
Product
Datapaq Solar Tracker System
-
The SolarPaq® Thermal Profiling Systems from Fluke Process Instruments are designed specifically for solar photovoltaic (PV) manufacturing including applications like contact firing, contact drying, anti-reflection coating for the solar cell, lamination and other thin film processes. These systems, consisting of user-friendly Insight™ software, Datapaq® Q18 data loggers, stainless steel thermal barriers, thermocouples with PTFE or mineral insulation and accessories, provide users with the tools needed to gather accurate, repeatable results for process optimization, maximize cell efficiency and throughput, and more.
-
Product
ESD Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
WCS Simulator
MS 1601
-
The WEAPON CONTROL SYSTEM SIMULATOR (WCSS) is used to simulate Aircraft Bomb and Rocket release commands for the LAB testing of WCSTS. The WCSS system simulates the High current and Low current signals according to the mode of operation (Series).
-
Product
Avionics Network Simulation Systems
-
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
Product
NVH Simulation
-
With our NVH simulation tools, you experience your data in form of virtual test drives, thus speeding up the development processes. Auralize transfer path analyses based on test bench data or evaluate the NVH performance of a system even before components and assemblies can be physically combined.
-
Product
Radar・Sensor Simulation Framework
COSMOsim
-
Millimeter Wave Radar simulator and LIDAR (Laser Imaging Detection And Ranging) simulator for Automotive sensor simulations, and also can provide 3DCG MAP for specific radar which has millimeter accuracy. Now we can only provide AMMWR and ALR to the following COSMOsim Framework. This simulator enables automotive manufacturers to simulate a driving situation by sensor-based modelling, check the recognition and control of autonomous driving, and verify the sensor-mounting positions on vehicles efficiently, which eliminates the need for test driving with real vehicles.
-
Product
Solar Power Meters
-
TES Electrical Electronic Corp.
Wide spectral range. Excellent long term stability.Cosine corrected. Automatic transmission measurements. Select either power or transmission. Solar energy measurement.
-
Product
Solar And Energy Storage
-
With proven expertise in solar power conversion and energy management, we utilize best-in-class technology to power photovoltaic systems worldwide.
-
Product
ARINC 429 Test And Simulation VME Module
VME-429
-
*8, 16, 32 or 64 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
-
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.





























