-
Product
Oil Tan Delta Tester / Tester System
-
The instrument is designed to test the insulation resistance of electronic and electrical components in the range of 1 Meg ohm to 10 Million Meg ohm.
-
Product
Digital Functional Test
CTS100i
-
Capable of performance testing to defined traceable standards, CTS100i is designed to test Military, Aerospace and Safety-Critical equipment. CTS100i is a cost-effective digital functional test system, available in single, dual and three bay versions.
-
Product
Qualified Hermetic EGT Thermocouple Upgrade
-
FIT-IT & FORGET-IT Eliminate Exhaust Gas Temperature (EGT) thermocouple concerns with AMETEK's new EGT thermocouple product offering for Frame turbine applications. AMETEK has worked closely with the turbine OEM to design and engine test this thermocouple as a direct replacement and upgrade for all new and existing EGT thermocouples. The new EGT thermocouples are qualified and meet all design specifications.
-
Product
Remote Control Voice Recognition Tester
BK3013
-
Ready to help you take on the leading edge of consumer technology, we have designed a machine that tests microphones which both use RF and are used for voice recognition. The BK3013 runs a uniform SPL sweep to calculate FRF and also runs an SPL sweep that allows you to test the SPL range of your mic. Our "Test Shop" program will show you the results in graphs and allows you to have the computer check specific points in the test.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device
779068-01
-
32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device - The PCI-6229 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Midi Rack 120*60*80cm
OTP2 module no.002
-
The rack serves as the basic structure for your individually designed test system. Various OTP² modules can be installed in the 120 x 60 x 80 cm rack in order to implement a wide variety of test requirements.
-
Product
24-Bit Precision Load Cell Input Card
PCI-9524
-
The PCI-9524 is a robust, multi-purpose module designed for turnkey material test systems (MTS). Equipped with four strain gauge-based transducer input channels, four general purpose analog input channels, and a 3-axis motion controller, the PCI-9524 delivers a complete hardware solution for MTS manufacturers. The PCI-9524 easily integrates physical quantity measurement and implements strategy of close-loop control in a single module package. For transducer measurement, the PCI-9524 supports sensitivity from 1.0 mV/V to 4.0 mV/V and provides a 1/200000 accuracy of measurement of full scale. These features make the PCI-9524 suitable for precise measurement in large-scale transducers.
-
Product
Laser Diode Characterization System
58620
-
The Chroma 58620 Laser Diode Characterization Station is a state-of-the-art full turnkey system specially designed for laser diode testing. Features range from macro inspection of the facet or aperture active area to a full suite of electro-optical parametic tests.
-
Product
Towing Dynamometer
RS-40K
-
RS-40K towing dynamometer is designed for testing today’s DOT Vehicles (Classes 5 and 6) which include trucks and buses. The RS-40K is built with a heavy-duty steel frame, industrial axle and rides on an air ride suspension. The RS-40K is designed to maintain 40,000 Newtons of constant drawbar force and the ability to simulate an uphill slope of 25%. The dyno uses eddy current absorbers with special high temperature coils. The power is provided by an industrial generator. Testing is unlimited at lowspeeds.
-
Product
Oil Quality Meter
-
Cooking oil is the mainly energy and nutrition source, and the cookingmaterial for daily life. Fried food is also favored as its unique taste . Withphysical and chemical reaction during the high-temp cooking process ,toxical chemicals will be produced. Currently, the traditional testing methodon cooking oil is mainly chemical method which is commonly used andconducted by professionals in the lab. But the lab oratory process alwaysproduces pollution and unnecessary waste . The Total Polar Material (TPM)values is the only acceptable standard which us ed for cooking oil testing.OS-27 is designed for cooking oil testing with safety and efficiency. It is ableto test total polar material (TPM) values in minutes and suitable for all kindsof cooking oil within high operation temperature.
-
Product
PXI 16 Trib Daisy Chain Switch Balanced 96 W
40-796-001
-
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779958-01
-
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Component Test Stands
-
As your specialist for measurement and testing technology, imc designs and manufactures test stands perfectly matching requirements for a complete range of components: whether for servomotors, pumps, brakes or valves – according to your wishes, imc component test stands can quickly and precisely test for perfect operation, verify lifetime, determine energy efficiency, and much more. Thanks to the modern software imc STUDIO, test objects can be tested for complex and wide-ranging scenarios.Test stand solutions from imc are characterized by their flexibility, short set-up times and productive test processes.As a manufacturer of measurement and test technology, it is second nature to us that imc test stands deliver reproducible and verifiable results and ensure productive test processes. Furthermore, we place enormous value not only on first-class technical features for imc test stands, but also on meeting the economic demands of our customers.
-
Product
Charge Coupled Device (CCD) Image Sensors for Space and Ground-Based Astronomy
-
(CCDs) for Space science, Ground-based Astronomy, and Earth observation applications with an impressive record of successful deliveries to a wide range of customers over 40 years.All Teledyne e2v devices can be supplied partially or fully customised to fit the application and achieve the best possible system performance. CCD image sensor design, manufacture, test and characterisation are carried out in-house enabling control from start to finish. Multi-polysilicon, multi-metal and back-illumination options are available for high resolution, high sensitivity and very low noise.
-
Product
Automatic Relay Test Set
DRTS 66
-
DRTS 66 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 6 Current and 6 Voltage generators simultaneously available.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510A
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
Loss Test Set, Return Loss Test Set
LTS1315, LTS1315R
-
The KD Optics LTS1315 is a combined mains / battery powered laser source and power meter designed to make attenuation testing in the field easy, reliable and most importantly, consistent. The LTS1315R incorporates return loss measurement (RLM) capability with the ability to switch very easily between dBrel and return loss.
-
Product
T6961 DIFFERENTIAL LEAK TESTER ENTRY LEVEL
-
T6961 was designed for ultra fast testing of small parts (pneumatic valves, pressure switches, micro-valves in plastic for medical use, needles, catheters, biomedical components etc.).This characteristics makes it suitable for use on high production automatic machines, allow assembly of the pneumatic unit behind the part being tested, for maximum reduction of the parasite volume. The differential measurement technology also allows detection of extremely low leaks (example medicinal valves: 10 cc/h at 2 bar in 0.1 s. of testing).
-
Product
[5kV AC] Hipot Tester, Rise/Fall-Time Control Function Equipped
TOS5200
-
TOS5200 is designed for AC Hipot Test with 500 VA capacity and 200 mA short circuit current output capability. Equipped with the PWM amplifier, the TOS5200 can provide a stable & reliable output without being affected by ACpower line. Therefore, it is a perfect solution for electronic equipment or devices complied to IEC, EN, UL, VDE andJIS etc. requirement.As TOS5200 covers most of features of our upper class model for AC Hipot Test, it achieves thesuperb cost / performance ratio for those who need 200 VA or 500 VA capacity, or both. Also, as it equips the Interlockfunction together with other safety features, operator can carry out the test with higher current value in safe.
-
Product
Fully Automatic Eddy Current Crack Test System
ROTO-SCAN
-
Foerster Instruments, Incorporated
The fully automatic crack test system ROTO-SCAN was specially developed for the testing of rings. The mechanical equipment has been developed for the gentlest possible handling of the test pieces and features a compact and low-maintenance design. The test probes seamlessly scan the inner and outer contours of the test pieces, thus ensuring 100 % testing of the rings.
-
Product
PXI-4110, 3-Channel, 20 V, 1 A, 9 W, PXI Programmable Power Supply
779647-10
-
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
Product
PXI Source Measure Unit
-
PXI Source Measure Units (SMUs) combine high-precision source and measure capability with features designed to reduce test time and increase flexibility. These features include high channel density for building parallel SMU test systems, deterministic hardware sequencing for minimizing software overhead, and high-speed update and sample rates for quickly changing setpoints and acquiring data. Additionally, the flexible sampling rate and streaming capability of PXI SMUs allows you to use the instrument as a digitizer to capture transient behavior, and the digital control loop gives you the ability to adjust the transient response of the instrument. The ability to change the transient behavior of the SMU, called SourceAdapt, reduces SMU settling time and minimizes overshoot and oscillations, even with highly capacitive loads.
-
Product
Spectrometer
LSCM
-
This device performs high-speed measurement and sorting of LED electrical and optical characteristics while synched with control signals from the LED production line inspection and sorting system. The LSCM then provides that pass/fail information to the system. The LSCM is equipped with the function to test both electrical and optical characteristics by applied voltage and current to the LED. This test device was designed to integrate test functions required by the inspection and sorting system into one compact body.
-
Product
Military Test Systems
-
Santa Barbara Infrared is the leading supplier of sophisticated, integrated, multi-function E-O test systems used by the military in laboratory, factory, depot and field test environments. Each of these systems are built to specific requirements and utilize SBIR’s extensive design and test capabilities, core technologies and knowledge of the unique military applications. SBIR specializes in providing complete solutions with integrated hardware and software resulting in robust and easy-to-use systems.
-
Product
PXI 8 Trib Daisy Chain Switch 75 Ohm 96 Way
40-792-701
-
The 40-792/793 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data. Traffic is sequentially Daisy- Chained through all tributaries (or any selection of tributaries), modules can be cascaded to test any number of tributaries.
-
Product
Printed Circuit Board Testing Solutions
-
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
Product
Quasar Smart Relay Tester
-
The Quasar is the most advanced three-phase relay test set designed for the testing of secondary and IEC-61850 protections of any type with special focus on industrial and routine maintenance applications.
-
Product
Test Solutions For MROs
-
Through our 50+ years of experience, we’ve designed equipment that test components on nearly all aircraft platforms. Because of our experience and our attention to industry trends, we can anticipate what components you’ll be testing tomorrow. We design our test stands to exceed your current test requirements for simple upgradability to ensure that you’re ready for the future.
-
Product
Towing Dynamometer
RS-25K
-
RS-25K Towing Dynamometer is designed for testing today’s full-sized SUVs and light trucks. The RS-25K is built with a heavy-duty steel frame, an aerodynamic body and rides on an independent, air ride suspension using two eddy current absorbers with special high temperature coils to absorb energy. The RS-25K is powered by an industrial generator so there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
