-
Product
Signal Generators
-
Are electronic devices that generate repeating or non-repeating electronic signals (in either the analog or digital domains). They are generally used in designing, testing, troubleshooting, and repairing electronic or electroacoustic devices; though they often have artistic uses as well.
-
Product
Panelized PCB Tester
-
Removable nests are designed to configure base test system to accept panelized circuit boards for rapid functional test.
-
Product
PXI 40Amp 14Volt 2xSPST Automotive Relay
40-180-001
-
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDCThe 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Programmable DC Power Supply
CBCT
-
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm With SPDT
50-293-111
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Ionic Contamination Test System
Omegameter SMD 650
-
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
-
Product
Vacuum Bottle Testers
-
Vanguard Instruments Company, Inc.
The VBT-75 S2 is Vanguard's second generation microprocessor-based, portable, 75kV dc vacuum bottle tester. This lightweight, portable tester is designed for testing circuitbreaker vacuum bottles in the field and at the shop.
-
Product
Testing Electric Pump Motors
-
This Custom Motor Test System is designed for the testing of 5 different sized electric motors used in various sump, utility, sewage, well, pool and pond pumps. All of the components mentioned above are mounted on a versatile table that can be easily reconfigured and retrofitted to any Magtrol dynamometer.
-
Product
Digital Surge Tester
25KV, 30KV & 40KV
-
The Digital Surge Tester is designed specifically to test the coils and windings of High range AC Rotating machines ranging up to 13.8KV. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
-
Product
Standard Test Chambers
-
HIACC Engineering & Services Pvt. Ltd.
Designed for testing the durability, safety, and performance of products under various conditions.
-
Product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
Primary Current Injection Testers
-
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
Product
Bench Power Supply
E3630 Series
-
When your requirements demand more power, the E3630 Series power supply offers up to 200 W per output. This linear power supply meets the requirements of the most demanding applications in R&D design verification, production testing, and quality assurance (QA) verification with reliability you can count on.
-
Product
Telecom Transmission Tests
-
Networked Communication Solutions, LLC
Is designed to test across the full bands of T1-Lite® or E1-Lite® or test individual timeslots.
-
Product
Power Induction Tester
MIG-ITU-K44
-
The MIG-ITU-K44 is designed for power induction testing at line frequencies of 50 and 60Hz. Power induction tests need only be performed at the frequencies of the public power supply or railway power of the country of application. Basic and enhanced level tests can be performed according to ITU-T K44.
-
Product
Mixed Signal Test Systems
MTS1000i
-
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
Dummy Test Wafers/Chips
-
Advanced Dummy Test Wafers/Chips available with over 35 different chip designs and choices of 11 different material configurations as well as kits complete with test vehicles. Custom-make test production of TEG wafer/glass (TEG=Test Element Group). Design and provide custom-make test kit.
-
Product
Custom Test Design
-
Materials Evaluation and Engineering
Some problems require solutions beyond the standard test methods and procedures routinely performed at MEE. Replicating the suspected cause of failure on an exemplar part can provide valuable information about the likelihood of that failure case. Likewise, intentionally causing component failures in a variety of ways can provide insight into possible failure scenarios. Wondering how (or if) a design or part can be tested? Give us a call – the engineers and technicians at MEE enjoy the hands-on experience of designing customized testing plans for your unique challenges.
-
Product
Programmable DC Electronic Load
63000 Series
-
The 63000 Series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power suppl ies, A/D power suppl ies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices. The 63000 Series offers models in two operating voltages 150V models, with 250W and 350W power levels up to 60A in a single unit. Their compact and light weight design make these loads easy to move around which is ideal for R&D and design validation. Each model of the 63000 Series has unique user-def ined waveform (UDW) funct ion capable of simulating real-world custom waveforms. In addition, a data storage function has been built in for saving and recalling up to 100 stored settings at any time. For automated testing, these save and recall functions can save a great deal of time. The 63000 Series has 3 power ranges that can precisely measure the voltage and current in real time. Since short circuit testing is a critical test item, the 63000 provides short circuit simulation to effectively address application demands for power and automated testing.
-
Product
High-Speed Embedded Host Electrical Test Board
HSEHET
-
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
Product
AC Load Banks
XL1500 Series
-
Mosebach Manufacturing Company
The XL1500 Series of resistive load banks are designed for testing power supplies up to 1500kW of various voltages.
-
Product
Mixed Signal Test Systems
MTS1010i
-
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm - SPST
50-294-124
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCIe® Gen5 NVMe SBExpress Test System
SBExpress-RM5
-
The SANBlaze SBExpress-RM5 is a complete turnkey PCIe® Gen5 NVMe SSD Drive validation test system. The SBExpress-RM5 feature set provides unique functions applicable to all aspects of a product lifecycle, from development and QA, to design validation and manufacturing test cycles. The ability to drive Gen5 NVMe SSDs with a wide range of configurable attributes provides engineers with a flexible, multi-controller supported validation test platform. Development, qualification, and certification test cycles can be highly automated, thus reducing overall test time, and rapidly surfacing errors and non-conformance.The SANBlaze SBExpress-RM5 hardware provides a rackmount chassis with sixteen dual or single port front-accessible drives.
-
Product
HPA General Purpose Probes
-
General Purpose Spring Probe contact solutions are designed for high volume testing and feature the industry-proven Pylon line. General-purpose probes are offered in both replaceable and non-replaceable options.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm - SPST
50-294-111
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Digital Dailysate Meter
Digital Dialysate Meter™ D4 & D6
-
The DIGITAL DIALYSATE METER is specifically designed to test both acetate and bicarbonate dialysate quality. Measure Conductivity, pH and Temperature to ensure proper mixing during dialysate preparation and as a final check of dialysate quality before hemodialysis treatment. There are no strips or reagents that expire or subjective interpretation of results. Internal sensors require the user to place the sample in the instrument, preventing contamination of dialysate by the measurement device.
-
Product
Ultrasound Watt Meter
-
Ultrasounds are used for a wide range of purposes, and it’s important that your ultrasound equipment is working the way it’s meant to be. Our ultrasound power meters, also known as an ultrasound wattmeter, are precision instruments designed to test and verify the output of therapeutic ultrasound devices.
