Performance Testing
determines degree of ability.
See Also: Conformance, Qualification, Benchmark, Failure Analysis
-
Product
Modulation Distortion Up To 43.5 GHz
S930704B
-
S930704B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 43.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Battery Discharge Test Unit
125V DC 100A
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
Digital/Analog Frequency Response Analyzer
8800 Series
-
The analyzer utilizes a digital “Sync” signal to provide synchronization between analog and digital hardware. The Model 8800 performs simultaneous analysis on both analog input channels and digital target processor, reliably capturing all data. Versatile by design, the Model 8800 digital interface can be disabled, via software, to use the analyzer in a standard 2-channel, analog-only configuration.
-
Product
Simulators
-
In-Phase Technologies simulators are designed to simulate our customer’s operating product, allowing them to perform testing and “what if” scenarios
-
Product
PCI / PMC / CompactPCI Test System
PCITS
-
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
CBRN Detectors
RIID
-
A Radioisotope Identification Device (RIID) is a small, lightweight, portable instrument that identifies radioactive materials by measuring the energy of gamma rays they emit. RIIDs can also perform spectroscopic analysis to distinguish between different radioactive isotopes.
-
Product
PXIe-S5090, 9 GHz PXI Vector Network Analyzer
787251-01
Vector Network Analyzer
PXIe, 9 GHz PXI Vector Network Analyzer - The PXIe-S5090 is a 2-port Vector Network Analyzer (VNA) that helps you measure amplitude, phase, and impedance. You also can use the PXIe-S5090 to perform time-domain analysis and to calculate the S-parameters of 2-port RF devices. It features a 300 kHz to 9 GHz frequency range, a wide dynamic range, and high sweep speeds for automated design validation and production test. Additionally, the PXIe-S5090 supports automatic precision calibration, full vector analysis, and reference plane extensions.
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Brushless/Servo/Stepper Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to brusheless, servo,stepper motor performance test.
-
Product
Network Analyzer
-
The Complete Bundle gives you every tool you need to see what’s happening in the 2.4, 5, and 6 GHz spectrum, track down problem devices, and validate Wi‑Fi performance with confidence. It combines the Wi‑Spy Lucid for tri‑band spectrum analysis, Chanalyzer for deep desktop insights, the MetaGeek App for quick mobile checks, Oscium Nomad for packet and performance testing, and Device Finder for locating troublesome transmitters. Together, these tools create an end‑to‑end workflow that helps technicians diagnose interference, verify network designs, and resolve Wi‑Fi issues faster.
-
Product
Digital Functional Test
CTS100i
Functional Test
Capable of performance testing to defined traceable standards, CTS100i is designed to test Military, Aerospace and Safety-Critical equipment. CTS100i is a cost-effective digital functional test system, available in single, dual and three bay versions.
-
Product
Universal Testing Systems (Up To 2000 KN)
Industrial Series (DX, HDX, KPX)
-
The Instron static hydraulic universal testing systems — part of the Industrial Series — are rugged, high-capacity frames built for demanding material tests in tension, compression, flexure and shear up to 2,000 kN. Featuring large-diameter columns and rugged components for superior frame stiffness and durability, these systems deliver reliable, repeatable performance for high-force testing needs in metals, composites, concrete, fasteners, and structural materials.
-
Product
Advanced Ethernet Tester
LinkRunner® 10G
-
Quickly test, verify, and troubleshoot 1Gig, Multi-Gig and 10Gig Ethernet (copper, fiber) including line-rate performance testing and packet captureLayer 1-7 AutoTest enables any technician to find network problemsMonitor networks for intermittent issues, every minute for up to 24 hours AllyCare-enables in-depth network discovery features and web remote controlLANBERT™ Media Qualification app tests the capability of premise cabling and media components for carrying Multi-Gig and 10Gig EthernetTwo LinkRunner 10G units can be used for line-rate performance testing to verify network capacity, performance and QoS, as well as service provider SLAs between sites
-
Product
Adapter/Stainless Steel
WADP-NMSF-01
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
VLF Test System
BAUR PHG 70 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
Electrical
-
This category covers test equipment required for electrical performance tests on Industrial Lighting, Street Lighting, Automotive Lighting, Appliances, Accessories & related products. A wide range of Electrical Test Panels, Electro-mechanical endurance test systems for many products, Appliance test systems and also a range of low energy spot welding machines (one of the very few products we make which are not test equipment). Equipment are custom built to suit specific customer requirements.
-
Product
Adapter/Stainless Steel
WADP-QNMNF-01
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Discrete Device Test System
-
capability to perform parallel testing of power discrete devices. As the standard specifications of mainframe, 341-TT/P has 1.2kV/20A and 351-TT/P has 2kV/50A capabilities. These systems have 2 testing subsystems, each of which has 4-station capability by multiplexing to 4 handler/prober stations for high volume production testing.
-
Product
Multiplexer For Transformer Testing
MUX-R
-
Raytech Multiplexer MUX R is designed to drastically reduce cabling time and increase test performance. It is made to be used with Raytech Winding Resistance and Turns Ratio Meters. Any MUX R configuration can be easily controlled by a Winding Resistance Meter touch panel or by remote.
-
Product
Sensor Technology
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is the only manufacturer to utilize all 5 types of online partial discharge sensor technology. Using multiple sensing methods ensures that PD activity is always discovered, located, and characterized. PMDT's handheld PDetector and PDStar units have more capability than the high-end diagnostic equipment of the past. The small handheld, battery powered unit can completely perform the test and analysis without the need of a PC. PDetector, PDStar, and PDiagnostic instruments feature high-resolution phase-resolved analysis of PD signals (PRPD and PRPS) in real time, so you get your test results instantly!
-
Product
JTAG Functional Test
JFT
Functional Test
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be transformed into re-usable test 'modules'. Pairing JFT with JTAG CoreCommander emulative test modules gives an effective, low-cost system for performing tests through embedded device peripherals (ADCs, Memory Controllers etc..)
-
Product
Winding Resistance Test
20A DC booster
-
The 20A DC STCS booster allows to perform resistance tests on a PT with a current up to 20 A DC. The option is used together with STS 5000 and STS 4000 and must be connected to STCS module.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Pro CABLE TESTER
PK-101/PK-101C
-
PK101 is an innovative tester to perform full cabling testing, displaying wiremap, cable ID, faults, toning and identify active network port on all common low-voltage cabling system in today's automated homes, network, telephone or video media, and determine cable run length up to 300 M.
-
Product
IP / Ethernet Testers
-
Anritsu's powerful Ethernet/IP network data analyzers incorporate the dual functionality of wire speed performance analysis and network monitoring in the same instrument. Multiple protocols can be decoded and displayed for captured Ethernet, SONET, or SDH frames at full wire speed up to 100 Gbps, augmented by an optional Decode Module and Expert Analysis Module.
-
Product
Automatic Relay Test Set
DRTS 33
-
DRTS 33 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 3 Voltage generators simultaneously available.
-
Product
Integrated Ultrasonic Level Gauge
HR9100T
-
HighReach Measuring & Controlling System Co.,Ltd
The circuit design selects high-quality power module components from the power supply part to select high-stability and reliable devices, which can completely replace the same type of imported instruments. The patented sonic intelligent technology software can perform intelligent echo analysis the debugging and the any OTHER Special the without Steps. This Technology has Dynamic Thinking at The Functions of the Analysis and Dynamic. Sound Wave at The Patented Technology of Our Company Makes at The Accuracy of at The Instrument Greatly Improved, at The Precision Liquid Level Reaches 0.25%, and IT CAN Resist various kinds of interference waves. This instrument is a kind of non-contact instrument, which does not directly contact with liquid., the instrument has a variety of installation methods. The user can use this manual to calibrate the instrument. All input and output lines Of the instrument have lightning protection and short circuit protection.
-
Product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
-
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
Product
EMI/EMC Testing
-
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
Product
Multi Scale Digital Durometer
MSDD-4
-
For the technician that must perform hardness tests on various types of non-metallic materials, Rex Gauge Company now introduces the Multi-Scale durometer test kit. The Multi-Scale base kit consists of a Rex Type A durometer, and your choice of one of more color-coded barrel adapters for D, B, C, DO, O, OO or OOO scales (see chart for applications).
