-
Product
Single Position Automated Electric Fluxer
-
Single-position fully automated electric fusion machine with a typical sample throughput of 5-7 samples per hour. Ideal for preparing fused beads for XRF analysis and solutions for AA, ICP, and wet chemistry analysis. Patent PendingTypical samples include: Cement, Clinker, Ores, Slag, Refractories, Ceramics, Catalysts, Glass, Rocks, Minerals, Soils
-
Product
High Speed Free Space Optical Detectors
-
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
Product
47~862MHz Four outputs FTTP CATV optical receiver
P9428
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai P9428, the operating bandwidth of 47 ~ 862MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver. Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit..
-
Product
Absolute Optical Encoder
A2
-
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
Product
Multiplex Optical Maintenance Meter
LS280
-
LS280 is used to measure optical maintenance factor for high power LEDs, LED module, LED bulb or other LED luminaries. It is the important measuring equipment for performing the reliability of illuminants. • Freely set the time interval and time extent for automatic measurement • LCD Display, connect with PC via RS232 and English version software. • The test results can export Excel or PDF format and easy to compare. It can be saved by LS280 software or by USB directly. • The engineer can do LED life analysis based on the LS280 test results. • LS280 worked with High Power LED Aging Test (LS600), Multiplex LED Temperature Test (TMP-8/TMP-16) and High and Low Temperature & Humidity Chamber (GDJS-*B), it can do Flux VS Temperature VS Time, which is a perfect instrument system to meet LM-80 request.
-
Product
Semiconductor Package Inspection System
-
NIDEC-READ GATS (Grid Array Testing System) series carry out open/leak circuit tests on semiconductor package (MCM/CSP/BGA).
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber
40-852A-118-HI
Multiplexer Module
The 40/42-852A-118-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Solder Past Inspection
-
From the innovative Z-Check 3D through to the entry level Z-Check 100 the entire range has been designed to provide accurate pad specific measurement of solder paste deposits, adhesives and component placement. Amongst its other features the Z check software comes with the convenience of a full SPC package as standard.
-
Product
Digital Video/Audio/Data Optical Transceiver
OD3000A
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD3000A digital series optical transceiver, adopts digital video coding technique and WDM technique to satisfied user's multipath digital video, audio, data, ethernet's long distant high quality optical fiber transmission because of its full-found. Product including single fiber one way digital video, single fiber 64 routes video, 128 routes audio and data uni-direction and bi-direction complication. OD3000A can transmit the camera audio/video signal, camera and tripod head control data as well as other control function to central control room from remote end by optical fiber. It can be widely used in the remote monitoring, video conference, video medical ， remote education and other systems of public road, traffic, industrial and mining, community ect.
-
Product
Optical Power Meter
TM103N
-
TM103N Mini-Designed Optical Power Meter is a self-developed test instrument , which is widely used for installation, operation and maintenance of fiberoptic network. And it can test six calibrated wavelength optical power within the range of 800~1700nm.
-
Product
Optical Chopper
SR540
-
Stanford Research Systems, Inc.
The SR540 chopper will handle all your optical chopping requirements?from simple measurements to dual-beam and intermodulation experiments. The SR540 has a 4-digit frequency display, front-panel frequency control, analog voltage frequency control and two reference outputs with selectable operating modes.
-
Product
Optical Power Meter
TM233
-
TM233 Handheld OpticPower Meter(TM233-OPM ) are mainly used for continuous optical signal power measurement，Low power microprocessor is used for control，The TM233-OPM has the advantages of fully functional and reliable performance. Widely used in optical fiber construction and maintenance, optical fiber communication, optical fiber sensing, optical CATV and other fields. Instrument mould adopts advanced cold shell molding process; beautiful and durable, Instrument mould Design meets Ergonomic requirements. The TM233-OPM uses the built-in detector, which can be protected well. With a small shape, you can choose the backlight display and automatic shutdown function, with ultra wide optical power testing range.
-
Product
Optical Oxygen Sensors
-
The analyzer is suitable for direct field installation (NEMA 4X) in hazardous area (Class I, Division 2). The optical fiber sensor platform allows small inline sensors to be installed into sample tubing lines (1/4”), flow cells using NPT fittings, or directly into tanks or process lines using our retractable “hot tap” sensor design. BOS optical oxygen sensors are impervious to typical O2 poisons (H2S) and interferences (combustibles, magnetic, CO2 and H2) with high accuracy and long-term stability measurements without the need for complex or advanced sample conditioning systems. The threaded version of the optical sensor has optional Dual Seal (ANSI/ISA 12.27.01) classification for high pressure applications up to 1200 PSIG (82.7 BAR).
-
Product
Optical, Color And Electrical Integrated Test System
-
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
Our individually calibrated LED spectroradiometers provide fast and accurate results for actual light measurement applications. It only takes a few seconds to measure and view the results directly on the display, or use the optional analysis and automation software for more in-depth research. Using the HPCS6500 Spectroradiometer, you can measure any or all of the following optical quantities:
-
Product
Fiber Optic Power Meters
FOD 1204
-
The FOD 1204 & FOD 1204H Fiber Optic Power Meters are intended for accurate measurements of up-to-date optical communication. Very small temperature and temporal variations of Loss in Fibers and Connectors. Calibration of Optical Attenuators, Light Sources etc.
-
Product
VOD Overlay 1550nm Direct Modulated Optical Transmitter
VOD1504
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VOD1504 is a high performance 1550nm direct modulated inter-cut (narrow-bandwidth multiplex) optical transmitter which design and manufacture specially for realizing two-way television interact operation (VOD) for CATV network, mainly used in second service area to inter-cut IP/QAM or local program. In the content distribute network system (CON), VOD1504 is the VOD flow rate loading equipment, also often called the edge IP/QAM optical transmitter.
-
Product
Silicon Optical Power Head
81620C
-
The new 81620C optical power head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81620C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
Fiber Optic Extensometer
-
Versatile and reliable fiber optic extensometer. Designed for harsh environment, these multipurpose extensometers are packaged to fit the challenging environment of any structure monitoring applications.
-
Product
PXI Single 2 Channel Optic Mux FC/PC
40-855-112
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Inductively Coupled Plasma Optical Emission Spectroscopy / ICP-OES Systems
-
Industry-leading performance, speed and ease of use – no compromises
-
Product
Triple IC Optic Node
OX 733
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Tecnology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -13 dBm Sensitivity- RF O/P at 0 dBm : 113 dBµV
-
Product
Automated Visual Control System for Canned Food in Glass Containers
-
The system is designed for visual quality control of food packaging products. The level of filling the jar with the product, as well as its closure, is monitored. During the development of the system, smart cameras from Sick were used, but a special illumination of our design was used to improve the image quality.
-
Product
Mini Optical Power Meter
BD-POW-01
-
Shanghai Baudcom Communication Device Co.,Ltd.
Mini-Designed Optical Power Meter is a self-developed test instrument which is widely used for installation, operation and maintenance of fiber-optic network
-
Product
Pro Optical Loss Test Set
CertiFiber
-
The CertiFiber Pro Optical Loss Test Set improves the efficiency of fiber optics certification. The Taptive user interface simplifies set-up, eliminates errors and speeds troubleshooting. A set reference wizard ensures correct reference setting and eliminates negative loss errors. Built on the future-ready Versiv platform, CertiFiber Pro Optical Loss Test Set (OLTS) provides merged Tier 1 (Basic) / Tier 2 (Extended) testing and reporting when paired with OptiFiber Pro module.
-
Product
Light Measurement Optical Filters
-
International Light Technologies
Optical filters are often used to attenuate certain wavelengths of light and produce an overall desired detector response.
-
Product
PXI Dual 2 Channel Fibre Optic LC
40-855-422
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Optical Time Domain Reflectometer
3000 Series
-
Shanghai Baudcom Communication Device Co.,Ltd.
BAUDCOM 3000 series Optical Time Domain Reflectometer (OTDR) is anintelligent meter of a new generation for the detection of fiber communicationssystems. With the popularization of optical network construction in cities andcountrysides, the measurement of optical network becomes short and disperse; The3000 series is specially designed for that kind of application. It’s economic,having outstanding performance.The ODTR is manufactured with patience and carefulness, following thenational standards to combine the rich experience and modern technology, subjectto stringent mechanical, electronic and optical testing and quality assurance;in the other way, the new design makes ODTR more smart and compact andmulti-purpose.
-
Product
Portable CMM with Point-and-Click Automation
zCAT
-
Powered by Verisurf AUTOMATE software – zCAT combines a revolutionary, lightweight and portable form factor with easy-to-use software that serves as a common, mobile platform for in-process inspection or reverse engineering.
-
Product
LXI 8:1 Optical MUX SC/PC Single Mode
60-850-211
Multiplexer Module
Fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching
-
Product
Optical CMM Systems
-
Our OmniLux metrology system is highly versatile and provides unparalleled levels of 3D CMM capture for component measurement in seconds. This high precision non contact, metrology system is extremely versatile because it measures components of any geometry and of any material. Geometries possible include: spheres, asphere, cylinder, internal bore, cone/taper, step height or freeform in any material such as polished or rough metals or ceramics and polymers. The Omnilux is fast and accurate because, unlike direct contact sensors, the use of optical sensors means that the whole surface can be analysed while the object is suspended in space, ensuring that no damage comes to delicate surfaces. Our easy-to-use software interface, developed from years of experience enables the operator to effortlessly control the system. Rich data analysis, automation and export of results for the immediate generation of reports as well as a compact footprint means OmniLux is the leading solution for production or R&D environments where reducing cycle times is critical to sustainable success.
