Product

Cable Sheath Testing and Fault Location System

Shirla

-

BAUR

Shirla - BAUR

Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation

Product

Precision Locating System

Pathfinder PLS

-

Rycom Instruments, Inc.

Pathfinder PLS - Rycom Instruments, Inc.

The Pathfinder PLS is RYCOM's Precision Locating System for the damage prevention specialist...

Product

Vibrating Wire Peripherals

-

Campbell Scientific, Inc.

Campbell Scientific, Inc.

Many Campbell Scientific vibrating-wire peripherals enable dataloggers to read vibrating-wire sensors (also known as vibrating-wire or vibrating-strip transducers). These sensors measure strain, load, pressure, and water level, and they output a frequency signal generated by a vibrating filament. Campbell Scientific also offers vibrating-wire dataloggers that read the sensors directly.

Product

3 Wire (Analogue) Earth Resistance Tester

2105 ER

-

Standard Electric Works Co., Ltd

2105 ER - Standard Electric Works Co., Ltd

● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.

Product

Probes With Lead Wires

-

Omega Engineering, Inc

Omega Engineering, Inc

Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.

Product

Stud Finders & Breaker Locators

-

Morris Products Inc.

Morris Products Inc.

Ultrasonic Distance Meter Laser Pointer measures from 2 feet up to 50 feetEasy-to-read LCD displayBuilt-in calculator for measuring areas and volumesAdds linear measurements, area and volumeMemory functionChoose from meter or foot unitsStud finder detects wood up to 3/4” with audio indicator & LCD displayAuto calibration stud detection

Product

Cable Fault Locating Equipment

-

Megger Group Ltd.

Megger Group Ltd.

Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.

Product

Mating Coax Connector and 20 Coax Pins Crimped (both ends) to 5' wires

GX96405-60

-

Marvin Test Solutions, Inc.

GX96405-60 - Marvin Test Solutions, Inc.

Mating coax connector and 20 coax pins crimped (both ends) to 5 ft wires

Product

IEC60695-11-2 Single Wire And Cable Vertical Burning Tester

CX-D12

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-D12 - Shenzhen Chuangxin Instruments Co., Ltd.

It’s strictly designed according to IEC60695-11-2, IEC60332-1, GB/T18380.11-2008, GB/T18380.12-2008 etc. Stainless steel screen with a sliding burner handle support for approaching or movingback the flame from the sample under test according to the CEI standards for test on cables.

Product

Vibrating Wire Dataloggers

-

Campbell Scientific, Inc.

Campbell Scientific, Inc.

Vibrating-wire dataloggers have the built-in capability to measure vibrating-wire sensors. These dataloggers use patented spectral analysis technology.

Product

Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density

PFM-711B

-

Prostat Corporation

PFM-711B - Prostat Corporation

- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)

Product

Wire Crimp Pull Sensor

Model MR06-200

-

Mark-10 Corp.

Model MR06-200 - Mark-10 Corp.

The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the handles together to increase tension on the sample until a break occurs. The peak force is recorded by a Mark-10 indicator. A rotating turret with slots of multiple sizes accommodates a wide range of wire diameters, up to 0.25 in. (6.4 mm).

Product

K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m

745690-K002

-

NI

745690-K002 - NI

K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.

Product

Service Drop Locator

VM-560

-

Vivax-Metrotech Corp

VM-560 - Vivax-Metrotech Corp

The VM-560 is a general-purpose locator used to detect buried pipe and cable services in a variety of situations. With a 50/60Hz passive power locating frequency and three active frequencies, the VM-560 locator will meet the requirements of those wishing to detect the presence of active power cables and to trace short ranges. The VM-560 transmitter also has the additional frequency of 8kHz Fault-find so it can be used to detect the presence of ground to sheath faults on cable when used with the VM-510 Stand Alone A-Frame fault locator.

Product

Wire And Cable

-

Chengdu Mengsheng Electronics Co., Ltd.

Chengdu Mengsheng Electronics Co., Ltd.

We provide a variety of wire and cable products, including insulated wires, power cords, stranded wires, solid wires, wiring harnesses and connectors. Our products are widely used in security, medical, communications, instrumentation, medical, home appliances, auto parts, military, aerospace and other industries. Our products strictly comply with the product certification standards of countries and regions such as UL in the United States, VDE in Germany, CE in the European Union, and BS in the United Kingdom.

Product

Partial Discharge Expert Diagnostic and Location System

PDExpert

-

Power Monitoring and Diagnostic Technology Ltd.

PDExpert - Power Monitoring and Diagnostic Technology Ltd.

The PDExpert is PMDT's third level of Partial Discharge (PD) Expert Diagnostic and Location System. It is a powerful, portable, multi-channel system of impeccable design used to analyze and pinpoint PD signals coming from a power asset within centimeters while the power system is energized. The system consists of UHF, AE, HFCT and ultrasonic sensors, one advanced UHF/PD signal processing unit, one oscilloscope, filters and other accessories.The system employs ultra-high speed data acquisition and advanced digital signal processing technologies, compares the UHF, AE and HFCT signals of different frequency ranges to determine if it is PD or noise, and locates the source in power assets accurately by utilizing Acoustic-Electromagnetic Combination Location Technique, time Difference of Signals' Arrivals (TDOA), and 3D Positioning Technology.

Product

Fault Locator

REZAP FAULTMASTER

-

Kelvatek Ltd.

REZAP FAULTMASTER - Kelvatek Ltd.

REZAP FAULTMASTER is an auto-recloser that keeps customers on supply during intermittent faults.

Product

Drawing Die And Wire Measurement

Wire Diameter And Roundness Measurement

-

Optik Elektronik Gerätetechnik GmbH

Wire Diameter And Roundness Measurement - Optik Elektronik Gerätetechnik GmbH

The DGMS is a measuring system for diameter and roundness of wires, drawing dies and enameling dies. The wire diameter is measured highly accurate by an image processing system. To measure the roundness, an additional special holder is necessary to rotate the wire for the diameter measurement in several azimuths. The accuracy of the measurement is ‹1micron.

Product

Field Portable Wire Analyzer

Model 2635

-

DIT-MCO International

Model 2635 - DIT-MCO International

The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.

Product

DC Earth Fault Locator

GFL-T + GFL-R

-

Technology Products

GFL-T + GFL-R - Technology Products

The DC Earth Fault locator is suitable to test the DC Battery System and Trace Ground Faults. The system is suitable for Power Plants, Sub-Stations upto 765KV and other industries. The system is highly capable in tracing and pin pointing the DC earth faults in a live system without requiring any shut downs. The receiver sensitivity of 1mA and better is capable to trace most complex fault.