Fibre Channel
Data transfer interface with speeds up to 2 Gigabit per second that maps to common transport protocols, i.e. IP and SCSI.
-
Product
16 Channels, 200MHz, 1 M Samples/Channel Buffer USB Logic Analyzer
La-Logic-16
-
The La-Logic-16 is a sophisticated PC-based logic analyzer. It captures at a maximum of 200Mhz on its 16 channels simultaneously into it?s deep 1M samples/channel buffer.It can also operate as a 16-channel pattern generator.It connects to the PC via the USB-port and does not require any external power. The package is complete with all accessories included to start debugging immediately.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 2 Channels
M2P.5911-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 8 Channels
DN2.653-08
Arbitrary Waveform Generator
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.442-16
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Portable Oscilloscopes With Isolated Channels
-
Portable oscilloscope with 2 isolated channels, 600 V CAT III, 20 MHz bandwidth, 2 GS/s ETS, double 8,000-count multimeter with power measurements, 31-order harmonics with 40 to 450 Hz fund.,colour screen, USB.
-
Product
3GHz Dual Channel Signal Generator 19" 1U Rack Module
LS3082R
Signal Generator
The LS3082R, 3GHz dual channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” space efficient, rack-mounted box. The LS3082R features two phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS3082R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
Infiniium EXR-Series Oscilloscope: 500 MHz, 4 Channels
EXR054A
Oscilloscope
EXR054A Infiniium EXR-Series, 500 MHz on all 4 channels, options for 7 instruments integrated in one, hardware accelerated plotting, and fully upgradeable to 2.5 GHz and 8 channels
-
Product
Single Channel Potentiostats
Apps-XM Series
-
This family of instruments is built on the technology of the ModuLab XM platform. Specific combinations of options, such as frequency response analyzers (FRA), current boosters, voltage boosters, are popular when the ModuLab XM is configured for given applications. We combine our design knowledge and industry experience to create a line of products with an application focus.
-
Product
32 Channel Driver
-
The MultiChannel RF Driver is a 32 channel signal generator / amplifier intended to drive multchannel acousto-optic cells such as the Harris H-601. The driver can be operated either as an RF amplifier, providing 32dB of gain or as a high power signal generator making use of a dedicated 1GSPS, 14bit digital synthesizer on each channel. Modulation can be performed through the use of the internal source, external global input, external individual input, or programmable 16K sample RAM lookup table.
-
Product
PXI 8 Bank 8 Channel 2 Pole Multiplexer
40-659-102
Multiplexer Module
Model 40-659 is an 8 Bank 8 Channel Multiplexer module with 2-pole switching, It uses high quality electromechanical relays and is suitable for switching signals up to 2Amp, 300VDC/250VAC.The 40-659 module is suitable for multiplexer applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based multiplexers do not have sufficient power handling capability such as switching medium power AC or DC loads or for slaving external relays, contactors and solenoids.
-
Product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 1 Channel, 500 MHz Bandwidth
M4X.2210-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
80 Channel Relay Multiplexer
DP-VXI-4017
-
DP-VXI-4017 is an 80 Channel Relay Multiplexer constructed using ‘2 Form A’ (DPST) relays. It is a ‘C’ size 1 slot register based VXI module. This 80 Channel Relay Multiplexer module is highly configurable. As an 80 channel multiplexer, one input can be multiplexed to any of the 80 outputs or vice versa. The 80 channel multiplexer is divided into 8 banks of 10 channels each. This combination allows the board to be used as one group of 80x1 or two groups of 40x1 or four groups of 20x1 or eight groups of 10x1 differential multiplexer. The banks are isolated from each other by tree switches. 8 tree switches are used, one tree switch for each bank. A common tree switch is used to group all the eight banks. For short circuit protection resistors are provided for all the common terminals.
-
Product
PXI MUX 4 Banks of 32 Channel 1 Pole
40-610-022-4/32/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Owon 8 Inch Oscilloscope 70MHz 100MHz 1GS/s 2+1 Channel
EDS-E
-
Shenzhen Chuangxin Instruments Co., Ltd.
- Bandwidth : 70MHz, and 100MHz- Sample rate : 1GS/s- 1M record length- Ultra-thin body- 8 inch high resolution LCD- Pass / Fail function
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
-
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
Product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4I.4470-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX3032T
Oscilloscope
350 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
500MHZ, 2.4 GSa/S, 20 Mpts, 2 Channel, 20 Vpp Function/Arbitrary Waveform Generator
T3AFG500
Arbitrary Waveform Generator
Teledyne Test Tools T3AFG5 and T3AFG10 series Function/Arbitrary Waveform Generators are a new family of low cost, high performance, single channel Function / Arbitrary waveform generators offering a high level of functionality and an excellent specification at a very competitive price point.
-
Product
16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT2
-
The DT2 module features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
PXI 23 Channel Low Thermal MUX
40-620-022
Multiplexer Module
Pickering 40-620 Multiplexer modules are similar to other Pickering Multiplexer cards except thermal EMF is substantially reduced to <1.5V with 250nV thermal stability. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC microvolt measurements.
-
Product
Dual Channel Day/Night Thermal Biocular
Recon® B2-FO
-
The Recon® B2-FO multi-sensor biocular combines long-range imaging and target geo-location in a compact, portable, lightweight package. Integrate B2-FO into a remote kit for wireless operation and live video streaming. Add on a 2.5x extender in the field to increase target range to >10 km for vehicle-size targets. Delivering crisp, clear thermal and visible imagery for target identification at maximum standoff, the Recon B2-FO gives forward observers the flexibility and performance required on today’s battlefield.
-
Product
Enhanced 16 Differential I/O Multi-Mode Transceiver Channels
DF2
-
Function module DF2 (Enhanced Version) multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
Product
WiFiScope WS6+SureConnect: 1 GS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-1000XMS-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
M2P.6546-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
(40×70×12mm) Full Function Single Channel Small Form Factor Pre-Amplifier EDFA Module
SPA4300-FM01
-
Hangzhou Huatai Optic Tech. Co., Ltd.
SPA4300-FM01 is a full-function single channel Pre-Amplifier EDFA module with digital control electronics, adopts subminiature 40×70×12mm compact package, combined with artistic package and best optic performance, creating the best flexible and variable low-cost amplifier in the market. This module is suitable for multiple network application, especially the application that requires 40GB/S transmission speed.
-
Product
WaveRunner Oscilloscope, 1 GHz Bandwidth, 4+16 Input Channels, 20 GS/s on 2 Ch Sample Rate
WaveRunner 9104
Oscilloscope
1 GHz, 20 GS/s, 4ch, 16 Mpts/Ch DSO with 15.4" Capacitive Display.
-
Product
Oscilloscope, 2 GHz Bandwidth, 8 Input Channels, 50 Mpts/ch, 10GS/s
WaveRunner 8208HD
Oscilloscope
2 GHz, 8 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch High Definition Oscilloscope.
-
Product
Single Channel Potentiostats
VersaSTAT Series
-
This family of instruments combines our option-based hardware and software platforms to create the most popular line of potentiostats. Introduced for the majority of researchers doing typical electrochemical experiments, this entire series gained a key improvement in 2018. As of August 1st, 2018, all VersaSTAT models have ± 2 Amp capability standard. Users can now study larger samples at faster rates.
