RF Amplifiers
take low power RF signals and output RF signals that vary in the same way as the input signal, but with a raised amplitude.
See Also: Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers, Microwave Amplifiers, Rf Power Amplifiers
-
Product
MS-M RF Connector Pins RG178
40-969-501-FC
-
This is a 30 piece kit of RF Connector Pins for MS-M Connector Housing, suitable for RG178 Co-axial Cable.
-
Product
Modular RF Systems
-
Becker Nachrichtentechnik GmbH
Flexible modular system for customer specific system solutions without the effort of development and construction. The range of module types covers from active multicouplers, programmable attenuators, delay lines, RF switches, switching matrices, BIAS-Ts, RF filters up to bi-directional splitters and combiners.
-
Product
RF Multiplexer 3GHz, 4 to 1
40-872-004
Multiplexer Module
The 40-872-004 is a 50 ohm 4-to-1 RF MUX available with 4 banks in a single PXI slot. Using modern RF relay technology, it features low insertion loss and low VSWR at an affordable price. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics up to frequencies of 3 GHz, with each path having a nominally equal insertion loss.
-
Product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Product
RF Shielded Test Enclosure, for Laptop Testing
JRE 2218
-
Breeze through laptop RFI and wireless tests with the 'bigger than-a-breadbox' 2218! Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan.
-
Product
RF & Microwave Cables
-
Low Loss, Low VSWR for Integrated Systems: MegaPhase also manufactures high performance coaxial cables using GrooveTube® technology for high power and phase-defined systems, including electronic warfare, telecommunications equipment and many other RF platforms on the ground, sea, air and space.
-
Product
26-Pin MS-M RF Connector Housing, Female
40-969-526-F
-
These components allow users or their designated cable assembly suppliers to create their own cabling solutions for use with the Souriau MS-M RF connection solution.
-
Product
Combustible Trip Amplifier Module
TA102A
-
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
Product
RF & Microwave Modules And Instruments
-
SHF Communication Technologies AG
In digital high speed test and measurement, a perfect clock signal is crucial for the generation of low jitter reference test signals. A SHF Synthesized Signal Generator (Synthesizer) used as a clock source can operate over several decades of frequency and is an essential part of any high speed test and measurement environment.
-
Product
SMART III RF Moisture Sensor
-
Results are continuous, instantaneous and non-destructive. Used among diverse applications including gypsum, powdered and granular materials, agriculture and wood products. Monitor required to complete system. (Sold Separately): SMART III RF LED Screen OR Touch Screen
-
Product
High-Power Directional RF Wattmeters
81600-A Series
-
The 81600-A series of High-Power Directional RF Wattmeters are designed to measure RF power in 50-Ohm 6-1/8 inch coaxial transmission lines. The RF power is directly displayed on the 4-1/2 inch triple scale meter.
-
Product
RF Switch Modules
-
Analog Devices RF switch modules include the highest bandwidth switch modules. SPST, SPDT, SP4T, SP6T, and SP8T versions (reflective and absorptive) are available for a wide range of power (up to 27 dBm) applications, including antenna switching, filter switching, and tuner applications.
-
Product
RF & Telecom
-
The new generation of RF PXI instruments from NI and Keysights provides speed, accuracy and flexibility similar or better than rack and stack instruments, but for a lower cost. NI LabVIEW coupled with PXI hardware provides the latest PC buses, processor’s speed and optional FPGA technology, to the most demanding R&D projects or mass production lines.
-
Product
Wattchman RF Station Monitor/Alarm Systems
81080 Series
-
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
Product
3D RF Noise Measurment System
EMI-360
-
3D RF Noise Measurement System EMI-360 to realize the new EMC measurement.EMC measurement is possible to realize a low-cost and time reduction.
-
Product
Concurrent Alternative RF & GNSS Signal Simulation
SimAltNav Replay
-
Non-GNSS sources of RF (radio frequency) are of interest in GPS-degraded or contested signal environments, with interest focused on LEO (low earth orbit) constellations. These systems offer high receiver signal power (relative to GNSS) and a secure & resilient link to augment GNSS.
-
Product
RF Front-End ICs
-
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Limiting Amplifiers
-
Teledyne Microwave Solutions (TMS) offer a range of Limiting Amplifiers which are used in instantaneous frequency and phase measurement receivers. The most important performance requirement of a limiting amplifier is to minimize output power variations, and provide a constant output over a wide input dynamic range.
-
Product
RF Acquisition Record and Playback Instrument
SARP-6
-
Saluki SARP-6 RF Signal Acquisition Record and Playback Apparatus is a portable RF signal acquisition record playback equipment. It can be used to directly acquire, record, and playback RF signal from 1MHz to 6GHz. Its data recording and bandwidth playback can reach 200MHz. The SARP-6 RF Signal Acquisition Record and Playback system is composed of up and down inverter module, high-performance ADC and DAC, and large capacity solid-state FLASH or high-performance disk. It is widely used in radar, GPS, communication, telemetry, as well as many other circumstances for civil purposes when acquiring signal and recording it down.Applications: Interference Analysis/Surveillance/Spectrum Management/Satellite Communications
-
Product
1 GHz RF Switch Module
1260-58
Switch Module
The Astronics 1260-58 is a high-density switch module with four 1x8 coaxial trees. The 1260-58 is intended for use with function/pulse generators, universal timer/counters, oscilloscopes, high-speed digital test units, and other instruments involving high-frequency or fast rise-times.
-
Product
RF Safety Monitoring
MVG EME Guard XS 6GHz
-
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
-
Product
RF Connector
-
Electrical connector designed to work at radio frequencies in the multi-megahertz range. RF connectors are typically used with coaxial cables and are designed to maintain the shielding that the coaxial design offers.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
RF Cables
-
RF/microwave interconnect and precision test cables for 50-Ohm and 75-Ohm systems from DC to 67 GHz with a wide selection of connectors including SMA, N-Type, F-Type, BNC, and 2.92mm!
-
Product
Distributed Amplifiers
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support distributed amplifiers that provide a simple and easy solution for a wide variety of commercial and aerospace & defense applications. MACOM’s distributed amplifier family cover frequencies from DC to 80 GHz and are offered in both bare die and air cavity packages. These devices offer an excellent combination of broadband performance and ease of use for a variety of high-performance applications.
-
Product
RF Signal Generators
-
Value for money RF signal generators with frequency capability from 1.0GHz up to 6.0GHz.
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
