Crawford Cells
transversal electromagnetic mode cells.
-
product
Your Automated Microscope For Live Cell Imaging
ZEISS Celldiscoverer 7
Combine the ease of use of an automated microscope with the image quality and flexibility of a research microscope. Whether working with 2D or 3D cell cultures, tissue or small model organisms, you will acquire better data in shorter times with this automated live cell imaging platform. Add LSM 900 with Airyscan 2 to gently image dynamic processes with highest framerates in superresolution.
-
product
Load Cells
Applied Weighing International Limited
Range of tension load cells are suitable for smaller Silo, vessel and tank weighing applications. The load cell can be supplied as a fully welded stainless steel or tool steel. Capacities from 1000kg to 5000kg Fitting options available including threaded bar, rod end bearing and eyebolts. ATEX option available.
-
product
Reference Cells For PIV-IV Systems
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
product
Load Cells and Sensors
AMETEK Sensors, Test & Calibration
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.The full bridge load cells and sensors provide high precision measurements that ensure adherence to the international standards.
-
product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
product
Small Cell/ Outdoor DAS Antennas
*Omni, Quasi-omni, Trisector, Cardioid and Bi-sector formats*Pole mounted and Stadium style antenna configuration*High band, low band and dual band models available*Integrates GPS antenna available on select models
-
product
High Precision Compression Type Load Cell
IR
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
product
Fuel Cell Test Station
E1PS is glad to bring you a low cost method to test fuel cells and produce professional test data results for under $1,000.00, fuel cell included! The Fuel Cell Test Station comes complete with everything but the hydrogen. There are three meters*, a load box, forced air housing and a fuel cell.
-
product
Redox Flow Cell Testing
Specifically designed for use with our Redox Flow Cell Test System. All non-metallic flow paths are made with non-corrosive, chemically resistant plastics only!
-
-
product
Single Point Aluminium Load Cell
EST-6
Technopark Automation & Control
The EST-6 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 500 mm. This load cell is available in capacities 500 kg and 1000 kg.
-
product
TurboFan Test Cells
Atec, Inc. is an industry-preferred provider of full scale TurboFan test cell design, construction, maintenance, and refurbishment. Our seasoned aeroengine professionals and comprehensive network of international locations and resources provide our customers with unparalleled expertise and value for their most critical and complex test cell projects.
-
product
Multiple Cell Battery Chargers
Renesas' highly versatile battery charger ICs support devices with rechargeable 2, 3 or 4-cell batteries and include configurations such as a hybrid power boost (HPB), narrow output voltage DC (NVDC), buck-boost NVDC, and SMBus Level 2.
-
product
Live Cell Imaging And Analysis
The Incucyte Live-Cell Analysis system is designed to efficiently capture cellular changes where they happen - in the incubator. Capture high-resolution fluorescence and bright field images and record data in real time over hours, days or weeks. From proliferation assays to immune killing of tumor spheroids, this flexible system enables users to observe and quantify complex biological changes in real time. Integrated software simplifies data analysis to speed time to answer while producing publication-quality graphs and plots.
-
product
Cell, Module & Pack Testing
Cell, Module and pack battery formats are crucial for electrification in transportation and energy. Arbin Instruments' test equipment is designed for performance-based tests, to meet the needs of these complex formats.
-
product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Load Cells for Weighing
HBM provides the optimal Load Cell or Load Sensor for your application. Beam Load Cells: The All-Rounders For Weighing Technology. Ring-Torsion Load Cells: Low Profile And Powerful. Canister Load Cells: Maximum Capacities Up To 400 t. Single Point Load Cells: The Standard in Scales Manufacturing. Digital Load Cells: Ideal For Dynamic Weighing. Weighing Modules: Pre-assembled For Tank And Silo Weighing.
-
product
OEM Weigh Cells
Our weigh cells feature electromagnetic force compensation, strain-gauge type load cells, and electronic modules for various scenarios.
-
product
Canister Load Cells
PCB's cost-effective canister load cells are easy to install and ideal for low-capacity applications. Canister style load cells include a built-in mounting base for a simplified installation in both tension and compression applications.
-
product
12 kV Insulation Fluid Test Cell
CP TC12
The CP TC12 oil test cell is for determining the relative permittivity, the dissipation factor and the power factor of insulating liquids such as transformer oil.
-
product
NI Real-Time Test Cell Reference System
778820-35
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
product
Load Cell Power Supply Module
MODEL PSM-F10
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
-
product
Direct Burial Half Cell Reference Electrode
DB-A
Model DB-A Copper-Copper/Sulfate Reference Electrode designed for direct burial for long term monitoring of buried or earth contacting structures.
-
product
Load Cell Transmitter
MODEL SST-HV
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
Load Cells
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
product
High Precision Canister Load Cell
Model 2000 Series
The Model 2000 Series High Precision Canister Load Cell was designed to accurately and precisely measure force, which many other quantities such as torque, thrust, and pressure are based, for aerospace applications. The Model 2000 Series, available with load measurement capacities up to 750K lbf, offers high performance and linearity and very low hysteresis. ±0.02% FS Hysteresis
-
product
Load Cells & Force Transducers
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
product
Permeability Cells
Flexible Wall Permeameter
The Permeability Cells - Flexible Wall Permeameter for Soil Samples performs permeability tests on normal and contaminated soil samples. The permeability cells are available either in brass for normal use or in stainless steel for contaminated materials. Top caps and pedestals are available for normal or contaminated materials.
-
product
Single Cell Hardware
A Fuel Cell Hardware Assembly consists of a pair of Poco Graphite Blocks with a precision, machined flow-pattern (pattern is serpentine unless otherwise specified by the customer), and a pair of gold plated connectors fastened with aluminum end plates. Gas inputs and outputs are through Swagelok fittings. A thermocouple well and two cartridge heaters are also provided. A single Anode Reference Electrode may be added for an additional cost. The FCT Cell Hardware does not include a Membrane Electrode Assembly (MEA).
