LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
product
W Series Panel Meter
ST-475
Standard Electric Works Co., Ltd
● Measuring Range : DC uA-200, 500 DC mA -1, 5, 10,15, 20, 30, 50, 100, 150, 300, 500 DC A -1, 5, 10 DC V -5, 10,15, 20, 30, 50, 100, 150, 300, 500● Accuracy : Class 2.0● Case and Composition: Acrylic Resin front and ABS Resin case Bezel mounting● Color：Black case, yellow scale plate.● Pointer：Tube type, black or red LED Custom ranges depend upon warrant quantity Suitable for VU meters of Amplifier usage
-
product
LED626/620 Goniophotometer For LEDs
Hangzhou Everfine Photo-E-Info Co., LTD
It can measure the luminous intensity data and automatically plot the luminous intensity distribution curve and luminous flux, and the test conditions meet the CIE condition A (far field) or condition B (near field).In addition, the software can provide customers with 3D luminous intensity distribution graphic.
-
product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
product
Long Term Test Kit
When long term electro-chemical tests (>1000 hours) are run to monitor the cell degradation at the cathode for example, it is important to avoid any contaminant in the gas flow rate.Inconel 601 flange equipped with alumina housing and alumina tube to feed the gas to the electrode during long term test (>1000 h)Typical poisoning is coming from the chromium contained in the steel tubing. The volatile chromium species (Cr6+) will flow into the cathode (with the air) and thanks to the intake of electrons at the electrode, the chromium ion will transform to chromium oxide and be deposited at the cathode triple point. In such a case, the long term test kit is used. The Inconel 601 flange is equipped with an alumina housing (>96 % Al2O3) and the air (or other gas) is led through an alumina tube. The long term test kit is fully compatible with other functionalities proposed with the Open Flanges™ test Set-Up as the integrated steamer or the small pellet test kit. The long term test kit can be implemented on the fuel, on the air or on both sides.
-
product
Infrared T1 3/4 LED
350-00003
T1 3/4 Infrared light emitting diode, for breadboard or through-hole projects. Used with the LED Standoff and LED Light Shield to build the IR Transmitter Assembly (#350-00017). Frequently used with the IR Receiver for object detection and autonomous robot navigation, this is a compatible replacement wherever an Infrared LED is found in any of our Education Kits Components Listings.
-
product
2U Family of Programmable AC-DC Switching Power Supplies to 1400W
The 2U family of programmable AC-DC power supplies sets a new standard for flexible and reliable power for your application. Available in a Rack Mounting or Benchtop at 1400W power levels with single output voltages ranging from 10 to 270V and current capabilities up to 120A. A user-friendly front panel provides reliable linear controls for finer adjustment and digital LED voltage and current meters. Standard features include; 'soft start' operation and 'no load' operation, thermostatically speed controlled fans to limit acoustic noise, short circuit and overload protection, thermal protection, internal EMI filtering, RFI shielding and remote sensing.
-
product
Test Board For QSFP28 Transceiver
EQSFP28
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Frequency Demultiplexer
Becker Nachrichtentechnik GmbH
Modern receivers for broadcast have a large number of antenna inputs for the different radio bands. The devices of the FDMX series can be used to supply the antenna inputs with RF signals. The devices of the FDMX series splits a sum signal in frequency division multiplex into the individual broadcast bands and the L1 satellite navigation band (GNSS). Additionally, DC loads are provided for each antenna input to simulate active antennas. The presence of remote power supply is indicated by an LED on the units.
-
product
Built-in LED Gem Tester
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
Gem Tester Refractive index is one of most important optical parameter. Gloss of gem can be estimated by the parameter.The kinds of gem can be precisely determined in accordance with the measured value of refractive index because every kind of gem has its inherent refractive. Besides, index of double refraction can be also measured. Through the parameter you can judge whether a gem is uniaxial or biaxial photopositive or photonegative.
-
product
CAS-200 Compact Array Spectrometer
CAS-200
Hangzhou Everfine Photo-E-Info Co., LTD
CAS-200 can quickly and accurately measure the spectral power distribution in the range of 380nm ~ 780nm, mainly measuring: the relative spectral power distribution, chromaticity coordinate, color temperature, color rendering index, color tolerance, peak wavelength, FWHM, luminous flux (with integrating sphere) of traditional lamps/light sources, single LED, LED modules and other electric light sources.
-
product
3U CompactPCI Serial M.2/U.2/SATA Storage Carrier
cPCI-A3H20
- 1x NVMe M.2 and 1x NVMe U.2 drive slot- 1x optional SATA 6Gb/s M.2 drive slot shared space with NVMe U.2- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Operating temperature: -40°C to +85°C with qualified modules- EN50155 compliant
-
product
LED Test Instruments
Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
product
200 KHz LCR Meter w/RS-232 Interface
LCR 200
Measurement Parameters : Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and £c. Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz Basic Accuracy 0.1% ; Test Voltage: 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only). DMM Functionalities. Dual LCD Display with LED backlit
-
product
In-Line Wafer Surface Defect Inspection
ALTO-SD-150/200
ALTO-SD SERIES IS AN IN-LINE INSPECTION SYSTEM SUPPLYING HIGH THROUGHPUT, FULL SURFACE DEFECT INSPECTION FOR ALL KINDS OF WAFERS INCLUDING SILICON, QUARTZ, SAPPHIRE, COMPOUND AND MEMS WAFERS. HIGH-RESOLUTION CAMERA OPTICS PLUS LED ILLUMINATION GUARANTEE RELIABLE DETECTION OF ALL LOCAL DEFECTS. IT INSPECTS DEFECT SIZE OF 1~ 10 MICRONS, CONFIGURABLE INSPECTION RESOLUTION TO OPTIMIZE DEFECT SIZE VS. THROUGHPUT. THE SYSTEM COMBINES HIGH-PRECISION MEASUREMENT, POWERFUL DATA ANALYSIS AND USER-FRIENDLY OPERATIONS.
-
product
Fibre Tracer
FT20
The KD Optics FT-20 is a small, hand-held, visible source used for tracing multimode fibre optic cables and is especially useful for identifing a single fibre in a multi-fibre cable. The unit has a bright LED output with a 2km range and is modulated at 2Hz.
-
product
Digital LOOP/PSC/LOAD Tester
2811 LP
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Displays and sound warning if external voltage present.● Displays mains voltage, scroll trough menus.● Checks wiring integrity (LEDs and display).● Single button operation.● Auto-off/auto-ranging.● Combined prospective short circuit current, PSC and LOOP tester.● Built-in carry case, test leads in separate pouch.● Loop test for L-E and L-N and PSC.● Voltage test L-N and L-E.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for special orders.● 60Hz available on request.
-
product
FMC SpaceWire/SpaceFibre Board
316
The FMC-SpaceWire/SpaceFibre board is an FPGA Mezzanine Card which is designed to extend the capabilities of an FPGA development board by adding support for SpaceWire and SpaceFibre interfaces. The board has four SpaceWire ports with accompanying status LEDs, and two SpaceFibre ports.
-
product
Radiation Survey Meter For First Responders
Radalert 200™
The Radalert 200 is a rugged solution for monitoring both ambient and elevated levels of ionizing radiation in challenging environments. Simplified user interface requires minimal training. Detects and measures alpha, beta, gamma, and X-radiation. Data is displayed in your choice of counts per minute (CPM), μSv/hr or mR/hr, or in accumulated counts. A red LED blinks and a beeper chirps with each count (can be muted). An audible alert sounds when the radiation reaches a user adjustable level.
-
product
Ultra-compact Photoelectric Sensor
EX-20 Ver.2
Panasonic Industrial Devices Sales Company of America
Using a single chip optical IC, Panasonic created the powerful EX-20 Ultra-Compact Photoelectric Sensors, which are among the smallest Photoelectric Sensors worldwide and in spite of their miniature size, the Sensors incorporate a sensitivity adjuster. Since a red LED dot light source is used, alignment and confirmation of the sensing position is easy, even if very tiny objects have to be detected.
-
product
Single Loop Controller
3200
The instrument has the largest red or green digital display in a 1/32 DIN package. In addition to the red or green display the 3200 benefits from three additional multi-colour LEDs to indicate process, alarm and configuration statuses.
-
product
13 Pin Towing Socket Tester ( For Halogen Light System)
7630
Peaceful Thriving Enterprise Co Ltd
The tester is to connect with the 12V 13-pin Euro-type socket. It can also connect with 7 pin socket through a 13-7 pin towing adaptor. The cable is long enough for user to do the test while sitting in the vehicle. The tester can also do self-test (not work for 7 pin socket), 12V power check, ignition and reversing light. Not available for Newer car with LED light. CAUTION: The self-test is not available with 13-7 pin towing adapter because there is no continuous feed via the 7-pin socket.
-
product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
product
Absolute Optical Encoder
A2
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
product
LEDs
Opto Diode manufactures best-in-class light-emitting diodes (LEDs) for a wide variety of applications that require rugged, hermetically-sealed packaging that can withstand extreme temperatures. Choose from our visible, near-infrared in wide, medium or narrow light patterns, our high-output visible LEDs in red or blue with narrow beam angles, or our high-power near-IR LEDs for night vision and surveillance applications. Ideal for medical, automotive, scientific, commercial, imaging, aerospace, and other demanding military or industrial tasks.
-
product
Wired Serial Device Server
SD-300
The Silex SD-300 and SD-310AN are designed to easily connect and share RS-232 serial devices over a wired or wireless network. Industrial automation, building automation, medical devices, security access and control, point of sale devices, LED signs, bar code/label and other specialty printers, or virtually any other device with a serial port can be now be enabled with secure, robust wired or wireless network capability.
-
product
PicoBuck LED Driver
The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.
-
product
High Power LED Photo-color-semi Automatic Selector
Shenzhen Chuangxin Instruments Co., Ltd.
Can divide LED in to several groups by chromatic coordinates, correlated color temperature, dominant wavelength or luminous flux.
-
product
LED Light Sources
LED light sources provide high power at a precise wavelength. A typical application for AvaLight-LED sources is fluorescence. They provide a long lifetime, short warm-up time, and high stability.
-
product
8-CH Relay Outputs & 8-CH Isolated DI Card
LPCIe-7250
LPCIe-7250 provides 8-CH SPDT (Form C) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are non-polarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments.
-
product
LED Illuminator
Luzchem's LED-Illuminator, is a compact system for irradiating samples from 3-200 ml in size. Features a unique 7-LED design with lenses that focuses all LEDs on one spot! LEDi-KIT3 includes Luzchem's standard RGB head, comprised of two red, two green, two blue and one white LED. Or, choose from our broad range of high-powered single-coloured LEDi-Heads.
