RF Attenuators
Used to reduce input RF & Microwave power by a fixed ratio – expressed in dB. (www.e-meca.com)
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
Attenuator
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
Product
Dielectric Loss Tangent and Transmission Attenuation Measurement System
RTS03
-
RTS03 measures relative permittivity (dielectric constant), dielectric loss tangent in the frequency range between 5GHz and 26.5GHz based on a correlation between measurement frequency and transmission attenuation as the microwave passes through the flat plane sample.
-
Product
Process RF Analyzer
IMPS-4400
-
The Sensortech Instant Moisture Profiling System (IMPS-4400) is a non-contact RF moisture profiling system for board manufacturers to improve and optimize production processes and meet quality standards, reduce energy costs, increase productivity, and generate revenue. The IMPS-4400 utilizes radio frequency antennas to analyze board moisture characteristics below the surface, which is critical information to ensure consistent quality of finished boards.
-
Product
RF Shielded Chamber
MIL-STD
-
A high performance RF-shielded chamber specifically designed for radiated emissions testing in accordance with MIL-STD-461E/F. This chamber can be used for conducted emissions, conducted immunity, radiated emissions, and radiated immunity testing.
-
Product
RF Milliwatt Meters
Type NDB-2 and NDB-3
-
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
Product
RF Amplifiers
-
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
Product
RF Power Meters
-
Peak Power Analyzer has been totally redesigned from the inside out. This meter is taking performance to a new peak and changing the way the industry views and analyzes RF data.
-
Product
RF Front-End ICs
-
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Microwave& RF Signal Generator
-
Berkeley Nucleonics Corporation
A low-noise, fast-switching, high power and offers wide frequency ranges.
-
Product
SMART III RF Probe
-
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
Product
RF Mixers with Integrated LO
-
Analog Devices RF mixers/multipliers include both active and passive, as well as broadband and narrowband, products. These devices promise high performance and flexibility to help designers achieve their target specifications, reduce design time, and optimize costs. With leading specifications including speed, dynamic range, noise figure under blocking, SFDR, and ESD performance, ADI RF mixers and multipliers help to raise the bar within RF systems.
-
Product
Attenuators
-
The National RF line of attenuators are compact, affordable attenuators which are ideal for insertion between a direction finding antenna and a receiver/transceiver, to aid in the DF process. In addition, they may be used in the laboratory for a low-power, in-line attenuation purposes. The affordable price is achieved by utilizing standard 5% tolerance resistors and commercial hardware. For laboratory purposes, an attenuation versus frequency curve (to 500mMHz) is provided.
-
Product
LXI Video RF Multiplexers
RF Multiplexer
Pickering's LXI Video RF multiplexers, high performance MUXs suitable for video switching applications designed for the switching of RF signals in 75 systems at frequencies up to 1GHz. These multiplexers are also ideal for 75 monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment.
-
Product
RF SCOE System
-
RF SCOE Systems require fast yet reconfigurable data processing as well as RF Modulation capabilities.For which FPGA Cards inside the PXI Frames are well suited.
-
Product
Digital Step Attenuators To 18 GHz
-
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
Product
Custom RF and Microwave Solutions
-
When you need a custom RF/Microwave solution for your critical application, Mercury Systems is the supplier of choice. With extensive investments in R&D, a world class engineering team and a wide breadth of competencies; Mercury Systems is uniquely positioned to take on the toughest technical challenges. When the competitors cut R&D funding, Mercury Systems invests heavily to develop cutting edge capability in SWaP-optimized, high performing products. As the leader in OpenVPX and OpenRFM, you can count on Mercury Systems to develop products that perform in your system.
-
Product
RF Architectural Shielding Products
-
EMI (Electromagnetic Interference) is often used interchangeably with RFI (Radio Frequency Interference). However, EMI can be any frequency of electromagnetic noise, whereas RFI is a relatively narrow range of electromagnetic noise on the EM spectrum. EMI Shielding can be used to mitigate electric and magnetic radiation across various spaces. Radio Frequency (RF) Shielding can be used to mitigate RFI with specifically designed enclosures that can block RFI. As well, RF Shielding can include application of RF Shielding paints, fabrics, and other materials.
-
Product
RF Shielded Box
LTL A4001
-
Liveon Technolabs LTL A4001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A4001 RF shielded test enclosure can comfortably house the intermediate device on test. LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
RF Management
-
ATX offers several high performance, modular and integrated, RF and L-Band signal management platforms. Operators can easily split/combine RF services in a cost-effective and space-efficient manner. The MAXNET II and SignalOn platforms are CCAP™ compliant and support DOCSIS® 3.1 services up to 1.2 GHz, and also deliver up to 4K QAM signals without impairment due to RF management. ATX also offers the most comprehensive line of RF amplifiers and related products on the market.
-
Product
RF Over IP
-
Quintech Electronics and Communications Inc.
Digital IF / RF Over IP Solutions.
-
Product
PXI Single 8 to 1 RF MUX MCX 75 Ohm
40-834-101
RF Multiplexer
The 40-834-101 is a 75 Ohm 8 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-834 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
RF Safety Monitoring
MVG EME Guard XS 40GHz
-
EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.
-
Product
USB/RS232/SPI Programmable Attenuator
RUDAT-13G-90
-
Mini-Circuits’ RUDAT-13G-90 is a general purpose programmable RF attenuator supporting frequencies from 10 to 13000 MHz with attenuation from 0 to 90 dB in 0.5 dB steps. Its unique design maintains linear attenuation change per dB, even at the highest attenuation and frequency settings. The attenuator is controlled via USB, RS232 or SPI. It comes housed in a compact, shielded metal case with SMA(F) input/ output RF ports (RF ports are interchangeable), a USB type Mini-B socket, and a 9-pin D-sub(F) RS232 and SPI port. Power can be supplied via either USB or the D-sub port. The RUDAT-13G-90 is supplied with our easy-to-install, user-friendly GUI software, API objects for Windows® environments, and complete programming instructions for 32 and 64 bit Windows® and Linux® operating systems. See p. 9 for a complete list of included accessories.
-
Product
13.56MHz RF Power
-
100 W to 2400 W. 13.56 MHz. Analog/Digital, RS-232, USB interfaces. Low Harmonic Distortion. Automatic and Manual Gain Control. High Speed Pulsing (Bursting) controls. Compatible with T&C's Matching Networks. GUI Software (complete PC control). Includes all essential RF power/communication cables and mounting brackets. Air cooled (Air & Water 1200 W +). Half rack mount or stand alone versions. Ideal for: Industrial, Scientific, and Medical Applications.
-
Product
RF Power Pallets
-
Macom Technology Solutions Holdings Inc.
MACOM is a leading provider of pallet amplifier solutions supporting applications such as avionics, radar, and industrial, scientific, and medical (ISM). Pallets are easy to use building block amplifiers ready to “drop-in” to higher level assemblies. Both standard and custom options are available to meet demanding customer requirements. We can design single or multi-stage pallets that integrate features including DC sequencing utilizing MACOM’s Power Management IC (PMIC), control/monitoring functions and output filtering to meet specific size and input/output requirements.
-
Product
Voltage Controlled Variable Attenuators
-
A voltage variable attenuator is an electronic device that provides a variable attenuation depending on the voltage applied
-
Product
High-Power Directional RF Wattmeters
81600-A Series
-
The 81600-A series of High-Power Directional RF Wattmeters are designed to measure RF power in 50-Ohm 6-1/8 inch coaxial transmission lines. The RF power is directly displayed on the 4-1/2 inch triple scale meter.
-
Product
RF PHY Tester
TLF3000
-
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
Product
RF ATE
-
IFF-7300S Series IFF/Crypto/TACAN Automated Test System. IRIS 2000/IRS 1200 ATE Software Revision Service. RF Expansion Module (RFEM).
