EV Test Systems
See Also: Electric Vehicle Test Systems, EV Testers
-
Product
Switchgear Test Systems / Circuit Breaker Testing
-
ACTAS test systems provide precise information as to the condition of the chamber and drive unit without requiring them to be opened. The sheer number of parameters to be determined, the wide variety of different types of switchgear equipment in use and the harsh environmental conditions encountered during on-site tests place extreme demands on test equipment.
-
Product
Keypad Test system
Mistral
-
Engineering Solutions Inc. (ESi)
The Mistral Keypad Test System has been designed to be the least expensive, easiest to use full featured tester for membrane switch assemblies. The idea is to combine a small, smart "pod" with a PC running software that makes full use of the Windows® graphical interface. Make it as easy to set up and use as possible yet include all the features you need.
-
Product
HEV & EV Power Tester
EVd-40
-
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.
-
Product
Resilient Modulus and Asphalt Testing System
-
The Resilient Modulus software features built and test sequences, and the capability to specify user defined sequences. Contact stress is automatically adjusted according to the above procedures as selected. Available waveforms include haver sine, sine, square and triangular, along with a user defined waveform selection. Optional peak & valley compensation ensures proper and quick matching of the load parameters. Real time displays of the prescribed versus actual dynamic load or the dynamic deformation measurements by each sensor are always present. Deformation ratio of the two sensors, Rv (to ensure that the two deformation sensors are in agreement) and Mr are also calculated in real time. During export, curve fitting is done to fit the results to models that predict Mr as a function of σm, σd, and CP (cell pressure). Four different functions are calculated automatically
-
Product
4 Quadrant Dynamometer Test System
-
Magtrol’s 4 quadrant motorized dynamometers provides expanded testing flexibility over a typical braking dynamometer. With the ability to bring the motor under test (MUT) to synchronous RPM before beginning a test, repeatability is improved. Since the motor windings are at ambient temperature before starting a ramp test, wattage is more consistent.
-
Product
AUTOMATIC WINDING TEST SYSTEM
VE9036SU
-
6 CHANNEL Microprocessor based Automatic Test System for Automobile Coils, Magnetos, Alternator, Motor Winding. Can Test : Impulse Winding Tester (IW), AC/DC HiPot, Insulation Resistance (IR), Inductance (L), DC Resistance (DCR)
-
Product
Mezzanine System Carrier
MMS8010 / MMS8011
System
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
Product
Display Test System
-
PIMACS provides the broadest range of display optical performance measurement system for optical testing of various samples including flat panel displays. We are specialized in testing all sizes of display modules and panels ranging from various field.
-
Product
Battery Test Systems
-
The Intepro’s battery test systems are configurable systems designed to test the latest Lithium Ion batteries and other high power density batteries and chargers. Combining high resolution, high powered charge and discharge systems, Intepro IBT line of battery test systems link to the battery management through the bus communication and fail-safe external monitoring of key battery parameters.
-
Product
Test Systems
-
This measurement system is the state-of-the-art acoustical analyser from Norsonic. Using the experiences and accumulated know-how from the previous generations of analysers, Norsonic is offering a multi-channel system with focus on user friendliness, high efficiency, and accurate reporting. The system has been designed for field testing as well as demanding accredited lab measurements.
-
Product
EV Charging Station
Residentual
-
BENEFITS OF RESIDENTIAL CHARGING: *Charge up to 7x faster than the Level 1 cordset that came with your electric vehicle. *Level 2 (240V) charging stations are more affordable than ever – starting at just $379! *Tax incentives and rebates offset purchase and installation costs, up to 100% in some areas *It’s more convenient to charge at home than using a public station. *Indoor/Outdoor rated (fully sealed NEMA 4 enclosures) *The Level 1 cordset that came with your electric vehicle can be used as a portable charging station or for a second charging station when you have company with an EV.
-
Product
Automatic Hardness Testing System
AMH55
-
Maximize your productivity and easily measure impressions on various surface conditions for a wide number of applications with LECO’s new AMH55. The AMH55 introduces LECO’s innovative Cornerstone® brand software to our hardness testing platforms, for increased usability, simplified reporting, and streamlined analysis times. Supporting accurate and efficient microindentation and Macro/Vickers hardness testing in fully automatic, semi-automatic, and lite configurations, the AMH55 is a valuable resource for users needing precise and productive hardness testing while tailoring the data and results to their needs.
-
Product
Circuit Breaker Test System
TDR900
-
It operates and records a circuit breaker’s contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.
-
Product
Mobile Measuring & Testing Systems
-
Individual testing tasks for technical plants and large machines often require the use of a large number of measuring instruments on site, which are difficult to network with each other and which, in the case of complex measurements, require a lot of experience and time in operating the measuring equipment and analysing the recorded measured values. The applications and possible uses can be quite different:
-
Product
High Power Laboratory Testing System
FTF-HP
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery PacksBi-directional DC power supply
-
Product
Battery Test System
WBCS3000Ls32
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10mA
-
Product
Low Voltage Burn-in and Test System
Max 450
-
For burning-in and testing DUTs such as microprocessors, DSPs and logic devices, which require low voltage. Output monitoring gives functional test results for every device during burn-in
-
Product
Multi-Stage Functional Test Systems
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
VIP Inflight Entertainment Systems
System
Astronics can outfit your entire cabin with the perfect A/V system to match your needs. From a custom monitor to a robust speaker system, Astronics' integrations will improve your inflight entertainment experience.
-
Product
PXI Test System
APT-1000
-
18 Slot NI PXI chassis (PXIe-1065)Amfax MDU with E-StopMAC Panel SCOUT Receiver chassis and tableProgrammable DC power supply4 channels- 0-30V 2AFan Vented 29u Instrumentation rackIndustrial PC i7- Windows 7 or 1024 inch touchscreen LED Monitor on armLight TowerCE CertifiedFully wired and testedFull documentation packDelivery and commissioning on site
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Battery Test Systems
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10
-
Product
Engine Test Systems
TITAN Engine
-
The TITAN engine test system series contains fully equipped engine test stands which are designed for various categories of internal combustion engines, ranging from light-to heavy-duty engines and also offering solutions for component tests such as testing the exhaust line. Further adjustment for off-road engines, powered two-wheeler engines, small internal combustion engines from carts, snowmobiles or motorboats as well as aircraft turbines are available. Additionally, it is also possible to test alternative engine concepts.
-
Product
Automated Robot Test System
ATS-8000A
-
High Power Pulse Instruments GmbH
The ATS-8000A test system is a fully automated 2-pin probing solution for HBM, TLP, HMM and CC-TLP on package- and wafer-level.Future extension for CDM is optional.
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
Function Test Systems
-
These specialist Automeg models test the function and integrity of wiring harnesses combined with active components such as relays, switches, contactors, diodes, LEDS, actuators and other active components.Our software takes the complex and traditionally long task of creating functional tests away from the test engineer and allows these to be created automatically, from existing ECAD data and our component library and automated software routines. All the different routes and subtests are automatically calculated in seconds.
-
Product
Test System
ITC57300
-
The ITC57300 Dynamic Parametric Test System mainframe accepts Test Heads that perform nondestructive transient measurements on semiconductor devices such as Insulated Gate Bipolar Transistors (IGBT), power MOSFETs, diodes, and other bipolar devices(requires additional optional bias power supplies and custom personality boards). Included in the mainframe are all test equipment and software necessary to analyze and perform resistive and inductive switching time, switching losses, gate charge, Trr/Qrr, and other transient tests.
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
Engine Emission Test System
-
By adding transient operation functions (self-learning/predictive driving + each test mode performing) to measurement•control panel, Ono Sokki can build up engine test system that can perform transient mode tests supporting worldwide gas emission controls including TRIAS, FTP, EURO, and ISO. (e.g. WHDC, NRTC).This system provides good reproducibility for Transient mode test. Delay compensation and rotation inertia compensation function have greatly improved as well as self-learning / predictive driving function.Automatically processes from measurement to data output of test result, in conjunction with gas emission analyzer, tunnels, gas emission particle measurement system, smoke meter, etc.
