-
Product
Industrial Gaussmeter
-
The industrial gaussmeter IGM11 is used to measure magnetic DC and AC fields. The measurands are flux density in Tesla or Gauss and the field strength in Amps per meter.
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
PSL-3424 Quick Test for 802.at and 802.3bt PSE's
-
Accessible from PSA Interactive or PowerShell PSA. Scans 2 to 8 PSE ports per test cycle. Automatically determines and adapts to PSE maximum assigned class. Tests PSE’s that grant full power via PD Classification or through PoE LLDP. Validates PoE Detection Acceptance and Rejection Range. Measures PSE Port Voltage at both minimum (DC MPS) and maximum (Pclass) load conditions. Reports PSE type (AT vs BT), maximum assigned class capability, and Pclass power capacity. Assesses Disconnect Power Removal response. Assesses Overload Power Removal response. Assesses LLDP Power Protocol and Allocations (PSL-3424L).
-
Product
Hi Pot Meters
-
The HI Pot Device is designed to Hi Pot de-energized 15kV class cables. The tool transforms 18 Volts from the battery to approximately 8,000 volts DC. When the battery is installed and the safety switch is in the closed down position, the unit is in voltage detection mode. The unit should be in this position when installing the device, as it will sound a warning alarm if you approach an energized source. When the safety switch is lifted and the toggle switch is switched up, the unit is in the Hi-Pot mode and the high voltage DC is being applied.
-
Product
5000 AMP DC Rectifier - Air Cooled, P/N 6037C1
-
Air Cooled SCR Controlled Power Supply, 50 KW, P/N 6037C1Input: 480 VAC, 60 Amps, 3 PH, 60 HzOutput: 6 to 10 VDC, 5000 Amps maxContactor and overload relay are installed for protectionStart / Stop capabilityEPO capabilityManual voltage control and current limitOutput voltage and current are displayed on the voltmeter and ammeterIndoor enclosure, 68″H x 65″W x 36″DAll input/output connections are inside the enclosuresEstimated weight: 1000 lbs.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785169-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Cable Assemblies
-
We offer a variety of cables covering DC to 110Ghz. Cable assemblies from 0-6Ghz we usually build in our Quick Turn Cable Assembly Shop, delivery is 1-2 days. We also offer some Low Loss Phase Stable from our quick turn shop; but some of the precision cables can take longer.
-
Product
Electronic Loads
SLM 1 / 4 Chassis
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
Programmable Step Attenuator, DC to 26.5 GHz, 90 dB, 10 dB steps
84906K
Attenuator
The Keysight 84906K programmable step attenuator offers coaxial measurements to 26.5 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 90 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with less than 2 dB of loss at 26.5 GHz. The compact size of the unit, 35 percent smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Conductivity / TDS Monitor / Controllers
750 Series II Conductivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Conductivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
16-Channel DAC Function Card
ProDAQ 3510
-
The ProDAQ 3510 DAC function card is a ProDAQ high-density card that fits into ProDAQ VXIbus motherboards and LXI function card carriers. This high-density card contains 16 independent, 16-bit DAC channels, and each channel is equipped with its own DAC. The ProDAQ 3510 DAC function card is specially designed for DC, low-frequency, and current loop applications.
-
Product
Active Splitter for CATV/SATV
HGS02
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Excellent, zinc alloy die-casting chassis. *All ports can be passed by DC.* 75ΩBritish F-type connector.* With separate holes for easy installation. *Low noise, high isolation design. *Frequency 950-2150MHz.
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
Stationary Battery Comprehensive Tester
SAT-AG Series
-
Shaanxi Aitelong Technology Co., Ltd
SAT-AG Series Stationary Battery Comprehensive Tester is a kind of product introduced according to the market demand, which integrates the two major functions: on-line monitoring and capacity check test, with higher integration and better functions.SAT-AG is specifically designed for the maintenance of the lead-acid battery discharge in the electricity and telecommunication sector. It is a new high-tech intelligent product that provides safe, reliable and convenient constant testing equipment for the DC system(Direct current system) users.
-
Product
AC & DC Electronic Loads
-
The Adaptive Power Systems Electronic Loads cover a wide range of power levels, voltage and current profiles and feature sets.Supported voltages range up to 1250Vdc or 350Vrms AC. From bench to system and DC or AC requirements, we can more than likely offer you the optimal programmable load to meet your needs.
-
Product
Alternate 0.50 (14.00) - 2.50 (71.00) General Purpose Probe
P2662BG-1R2S
General Purpose Probe
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 30Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 68Full Travel (mm): 1.73Recommended Travel (mil): 50Recommended Travel (mm): 1.27Overall Length (mil): 575Overall Length (mm): 14.60
-
Product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
Simulator
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
Fluxgate Magnetometer Fluxmaster
-
Hand-held instrument for precise measurement of weak magnetic field from 0.1 nT to 200 µT (DC to 1 kHz). Typical applications are: Measurement of the Earth's magnetic field vector components, detection of AC fields from power lines, paleomagnetic investigations, package inspection according to IATA 953, and residual field measurement.
-
Product
PXI Dual 3-Channel 30A Solid State MUX
40-667-011
Multiplexer Module
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the 40-666/667 User Manual.
-
Product
6U Power Supply Mainframe. Accepts Two Programmable Power Modules
GX7400A
Power Module
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
Product
3GHz to 20GHz Microwave Mixer with Wideband DC to 6GHz I
LTC5552
-
The LTC®5552 is a high performance, microwave double balanced passive mixer that can be used for frequency upconversion or downconversion. The device is similar to the LTC5553, but with a broadband, differential DC to 6GHz IF port. The LTC5552 is recommended for applications where the IF frequency range extends below 500MHz. For applications where the IF frequency is always above 500MHz, the LTC5553 is recommended, since it includes an integrated IF balun.
-
Product
Integrated Balun Probes
-
This is an example of a 900 MHz Integrated Balun Probe. It incorporates a 50 ohm unbalanced to 200 ohm balanced differential transformer. The probe can be built with or without a center tapped ground needle and may also incorporate DC bias through the differential pair or via separate needle contacts.
-
Product
Adapter/Nickel
WADP-NFSM
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
-
Product
PXI Hybrid Dual Transfer Switch, DC to 26.5 GHz
M9156C
Switch Module
M9156C PXI Hybrid Dual Transfer Switch, DC to 26.5 GHz
-
Product
Standard 0.50 (14.00) - 3.40 (96.00) Non Replaceable General Purpose Probe
C-S-C
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 45Full Travel (mm): 1.14Recommended Travel (mil): 30Recommended Travel (mm): 0.76Overall Length (mil): 395Overall Length (mm): 10.03Rec. Mounting Hole Size (mil): 46.5Rec. Mounting Hole Size (mm): 1.18Recommended Drill Size: 56
-
Product
Environmental Chamber
REXMED REC-200
-
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Power Meters
Power Meter
Teledyne Test Tools range of digital power meters are for single-phase (1P/2W) AC power measurements with a test Bandwidth ranging from DC, 0.1 Hz to 100 kHz. The T3PM1006 model features a 4” TFT LCD screen with a five-digit measurement display. It offers 19 power measurement parameters to choose from, integration measurement function, front/rear panel input terminals, and various communication interfaces to help users to make convenient and accurate power measurement. The T3PM1100 model offers DC, 0.1 Hz ~ 100 kHz test bandwidth, 16 bits ADC, and 300 kHz sampling rate. It features a 5” TFT LCD screen with a five-digit measurement display. It also has options to display waveform (voltage/current/power), the integration measurement function, harmonic measurement and analysis of each order (meeting the IEC 61000-4-7 harmonics measurement requirements at 50/60 Hz), external sensor input terminals, and various communication interfaces to help users to make convenient and accurate power measurements.
-
Product
Insulation Resistance Meter
AMIC-5005
-
Insulation resistance measurement - 15TΩ: * 50 - 1000 V, in 10 V steps, * 1000 - 5000 V, in 25 V steps ; Memory of 999 results and transmission to PC ; Measurement of AC and DC voltage and capacity ; Measurement of leakage current ;Function with digital filter
-
Product
Programmable High Power DC Power Supply
ADG series
-
Preen’s ADG series is a programmable DC power supply with high power density and high output power, and offers many great advantages on response time, accuracy and output voltage range. ADG is an excellent source for testing or facility type applications, such as aerospace, renewable energy, automated test system, battery and server. With power level up to 80kW per unit, the ADG series provides output voltage up to 1000V and high output current of 2000A after custom modification.
-
Product
Unipolar D/A Converters
-
Analog Devices offers the broadest portfolio of low voltage single-supply d/a converters in the industry, which includes many leading products in performance and package size. A wide variety of applications use ADI precision nanoDAC® products because of their small footprint and robust range of features, including 8- to 16-bit resolution, low power, a fast 50 MHz SPI or 3.4 MHz I2C interface, and more, in a tiny package option. ADI’s nanoDAC+® products offer enhanced features such as higher accuracy, improved dc performance, increased robustness, and lower glitch energy, among other advantages.
