-
Product
Surge Generator
CFL SG 0810
-
SCOPE offers CFL SG 0810, Surge Generator with output of 8kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to MV. CFL SG series is equipped with different Protections, Interlocks and Auto-discharge facility to ensure user safety during operation. User friendly controls, adequate form factor, contact free HV terminations makes this CFL SG series most durable and best-designed sets in the segment
-
Product
Visual Fault Locator ( VFL)
TM315N
-
The TM315N Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network during and after installation.
-
Product
Surge Voltage Generator
SSG 3000
-
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
Product
Power Meter
-
OrienTek Optical Technology Ltd.
Power Meter and the Visual Fault Locator.The Optical Power Meter can measure dBm,dB and uW in the wavelength band of 850,1300 1310 1490 1550 and 1625nm.The Visual Fault Locator uses CW mode and Modulation mode and helps to detect the optical cable of up to 10km. Battery performance 50 hours operation,Dust and shock proof design,Auto Shut off function.
-
Product
Portable GIS Partial Discharge Detector
JHPD-10
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
Product
Surge and Test Generator
STG 600
-
Cable fault location with the BAUR STG 600. The STG 600 surge and test generator is a multifunctional cable fault locator for low voltage networks. The surge and test generator is used for cable testing as well as for precise location of high-resistive and intermittent faults in low voltage cables.* Specifically for use in low-voltage networks* High surge energy: 600 or 1000 J** Light, compact and transportable* Single systems for cable testing and faults location
-
Product
Time Domain Reflectometer
TDR 500
-
Handheld Time Domain Reflectometer. The handheld time domain reflectometer TDR 500 and TDR 510 are used for fault location in all metal cables such as power cables, coaxial cables, data cables and communication cables.* Configurable for various measurement ranges and cable types* Standard-compliant, safe measurements on life cables through the measurement category CAT IV / 600 V (with separation filter)* Ideal for fault location in the area of telecommunication, video technology, data and security technology
-
Product
Fault Locator
SNOOPi
-
SNOOPi employs a bespoke optical sensor to detect and discriminate between fault and natural gas.
-
Product
Intelligent Cable Fault Locator
TM800
-
TM800 Cable Fault Locator is a portable field instrument working on TDR and bridge methods, adopting advanced micro-electronics technology. It is designed to locate accurate fault points in such cables as telecommunication leadsheathed cable, plastic cable or user’s lead covered wire, while the faults include break, mix, earthing, defective insulation, or poor connecting. It is and ideal function-stable instrument for the field operator to improve work efficiency, in addition, it can also be used for circuitry project checking electric property testing of the cable.
-
Product
Search Receiver
KMF 1
-
Cable fault location with the BAUR KMF 1. The KMF 1 search receiver is used according to the step voltage method. The cable line is scanned with two measurement probes that can be dismantled during transport. The battery-operated device is also suitable for locating multiple consecutive sheath faults.* Battery mode* Zero point compensation* accurate location of cable sheath faults* battery test
-
Product
Traveling Wave Fault Locator
XC-2100E
-
XC 2100E, a Fault Location System based on principle of travelling wave detection is the solution to above problem. It can detect not only permanent fault, but also transient fault within one tower span accuracy (with best accuracy of ±50 meters). It is a kind of Line Monitor for continuous monitoring of transmission lines and gets triggered whenever travelling waves are generated on line due to switching, lightening or fault.
-
Product
Split-type Cable Fault Location System
-
Weshine Electric Manufacturing Co., Ltd
Electricity networks have had to become more flexible, reacting more quickly to the changes and needs of higher performance. This demand for flexibility is especially true where multiple generation sources occur, such as the intermittent power from renewables like solar and wind energy. While modern SMART grid technology can quickly identify faults in sub-station and generating units, cable faults can still occur anywhere on the network.
-
Product
Cable Test Van
-
Techno Instrumentation (India) Private Limited
Cable fault locating van with installation according to users specifications and requirement.
-
Product
Ground Fault Location
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of ground fault locator from basic to advanced model to fast detect, trace and pinpoint virtual grounding faults in DC systems when systems are LIVE (working online). Without injecting any signal to the DC system, they are safe to your existing system. With Kongter’s unique technique for signal tracing, these ground fault locators are much faster and more effective to find the earth fault in the field than its peers.
-
Product
Recloser Controls
-
Schweitzer Engineering Laboratories, Inc.
Recloser controls provide fault location, isolation, and system restoration using protection and communications capabilities, such as Automatic Network Reconfiguration and single- and three-phase tripping. They allow you to automatically reconfigure your distribution system to isolate faults, quickly restore service, and reduce customer impact.
-
-
Product
Cable Test Van
BAUR Transcable 4000/S 110-1
-
Transcable 4000/S 110-1. The transcable 4000/S 110-1 cable test van is a 110 kV cable fault location system in single-phase version. The system is actuated with the semi-automatic MGS control unit. The high voltage switch unit is single-phase, up to 32 kV, the 110 kV switching level is designed as air-insulated ceiling switch.
-
Product
Cable Test Van
BAUR Transcable 4000/S 32-3
-
Transcable 4000/S 32-3. Thetranscable 4000/S 32-3 cable test van is a 32 kV cable fault location system in 3-phase version. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is maintenance-free and fully safe to touch.
-
Product
Visual Fault Locator
FFL-310-U
-
FFL-310-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in -CW (continuous) or … MOD (1Hz modulation) mode. There is one LED indicator：with RED or GREEN light; the RED one shows the operating mode of the laser diode output signal, and the GREEN one indicates low battery level. FFL-310-U is designed in a card-size dimensions.
-
Product
Audio Frequency System
Locator Set / UL 30
-
Cable fault location with the BAUR Locator Set / UL 30. The audio frequency system Locator Set is used to exactly determine the alignment of cables and metal gas or water pipes. With various accessories, this system becomes a universal, indispensable device for power companies, industries, installation companies and water suppliers.* Output energy up to 50 VA* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output
-
Product
Surge Generator
-
Techno Instrumentation (India) Private Limited
LT to HT 11 kV and 33kV Surge Generator is an all in one solution for thumping, DC high voltage testing(Hipot-test) and burning for effective fault location in LT to HT 11 kV and 33kV cables.
-
Product
25-Watt Transmitter
Loc3 25W
-
The powerful 25-watt transmitter is the go-to transmitter for cable fault locating, finding holidays on coated pipes, problematic deep-buried lines, and long-distance pipe and cable locating. The Loc3-25Tx is also well suited for applications for cathodic protected longline pipelines and gas distribution in city areas needing a low-frequency high output transmitter.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
Electrical Test Instruments
-
Transcat offers all types of electrical test instruments for diagnosis, troubleshooting, and repairing of any products and devices. Our wide array of handheld, bench, and portable equipment covers virtually every electrical testing application. Whether its battery testing, fault location, or resistance testing Transcat has all the essentials to outfit an electrician.
-
Product
Power Cable Fault Locator
TM500
-
TM500 Power Cable Fault Locator adopts international advanced electronic testing technologies and SCM technology, and combines low-voltage pulse reflection and pulse current testing methods, is suitable for the precise range finding of power cable high resistance, flashover, disconnection, and low resistance. Low-voltage pulse reflection method applies to test the range of the low resistance and broken line, and the length and wave velocity of various cables. Pulse current testing method can be divided into breakthrough high-voltage flashover and DC high-voltage flashover for the high resistance and flashover cable fault finding.
-
Product
VDSL Tester
X5008
-
X-5008 VDSL tester specially designed for slid line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL, VDSL2 etc) and maintenance It provides xDSL test, PPPoE dial test, DMM test, Modem emulation, line voltage indication and so on. X-5008 VDSL Tester also introduces the Optical Power Meter and Visual Fault Locator function into the unit, as well as the TDR function. It is one mufti-function tester with smart size, true color LCD and powerful management software as well as the 6600mAh rechargeable battery etc.
-
Product
Under Ground Cable Fault Locator
-
Widely used in electrical and power generation sector for testing underground cables in order to detect any fault.
-
Product
Fault Locator
WEEZAP
-
WEEZAP is an LV vacuum circuit breaker combined with advanced measurement and protection capability.
-
Product
Optical Visual Fault Locator
SAT-3C01
-
Shaanxi Aitelong Technology Co., Ltd
SAT-3C01 Optical Visual Fault Locator is used for optical identification, fault locating of SM fiber or MM fiber, which is a basic maintenance tool of optical network, LAN, FDDI, ATM optical system, and telecom network system, suitable for field working.
-
Product
Platinum Tools Fiber Optic Visual Fault Locator
#TVFL100
-
Fiber optic visual fault locator works with virtually all 1.25mm and 25mm fiber optic sizes and connector types.
