Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
2-26.5 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5026
The HMMC-5026 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-26 GHz frequency range. Typical applications of the HMMC-5026 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-26 GHz frequency range.
-
product
Variable Gain Optical Amplifier Module
VGA4700-FM06
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VGA4700-FM06 series is a next generation variable gain optical amplifier module, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-7 FPGA - 6U VPX
Model 58720
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- One or two DUCs (Digital Upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connectionsto the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Low Noise Pre-Amplifiers
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
product
USB Preamplifier, 2 to 50 GHz
U7227F
The U7227F, 2 to 50 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
product
4-Channel 200 MHz A/D with Multiband DDCs, Kintex UltraScale FPGA - 3U VPX
Model 52862
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four wideband DDCs and- 32 multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
-
product
Hybrid Raman/Er-doped Fiber Amplifier
HFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600nm.
-
product
Switched Limiting Amplifier With Detected Output
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
CATV Booster Optical Amplifier
HA5100
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
product
Amplified Spontaneous Emissions (ASE) Sources
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
product
Low Noise Amplifier
1010
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
product
Solid-State RF amplifier module for High Power Testing
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
-
product
Small Diameter Tubes Optical Bubble Sensor
BE-A
Panasonic Industrial Devices Sales Company of America
*One-touch Attachment*For Small Diameter Tubes*High Speed Response Time*Ultra Compact*For A Wide Range Of Power Supply Voltages*Built-In Amplifier*Allows For Close Proximity Attachment*CE Approved*CE: EMC Directive
-
product
Amplified Photodetectors
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
-
-
product
Amplified Torque & Load Cell Indicator
9834
For use with amplified load cells and rotary torque sensors. Features 120 readings per second, programmable +/-10V or 4-20mA analog output, peak and valley monitoring, RS232. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector.
-
product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
