Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 57851
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Low-noise High-voltage Amplifier For Tube-scanners -
HV200/5
-
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
Product
Panel-mounted Amplifier(Power System Simulation )
PA30Bi-H
-
PA30Bi-H is the panel-mounted type power amplifier model which can produce 3-phase current, with maximum RMS phase current of 30A and maximum output power of 450VA, and 4-phase voltage, with maximum RMS phase voltage of 250V and maximum output power of 75VA.
-
Product
High Speed High Voltage Amplifier
WMA-300A/360
-
The WMA-300A/360 model is a -180V to +180V (360Vpp) high speed, high voltage amplifier designed for driving capacitive loads, such as piezo actuators, capacitive MEMS and EO-modulators.
-
Product
Premium Headphone Amplifier
A 20
-
A new standard for headphone amplifiers that brings out the potential of Tesla drivers. Premium headphone amplifier that inherits the design of A 1.
-
Product
CATV Separate Raman Amplifier
RFA4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Amplifier is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. Raman amplifier is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Broadband Amplifier
BBA150
Amplifier
The R&S®BBA150 broadband amplifier family generates power in the frequency range from 4 kHz to 6 GHz. The compact amplifiers are rugged and feature high availability.
-
Product
Current Amplifier/Generator
ULCA-1
-
The Ultrastable Low-noise Current Amplifier ULCA-1 is designed to fulfill the needs of high-accuracy low-current generation and measurements in the range from 1 fA to 1 µA (licensed by PTB).
-
Product
Amplifier Module
LNAM-B
-
Fully differential ultra-low-noise voltage amplifier module (LNAM) with selected bipolar rf transistors at the input stage. The amplifier exhibits ultra-low voltage noise, very high speed, and good dc precision. 50 Ohm input termination realized by negative feedback allows for the lowest possible noise temperature.
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Semiconductor Optical Amplifiers
-
A Semiconductor Optical Amplifier (SOA) is essentially a laser diode (LD) with no feedback from its input and output ports and hence is also referred to as a Traveling-Wave Amplifier (TWA). Semiconductor Optical Amplifiers (SOAs) have proven to be versatile and multifunctional devices that are key building blocks for optical networks.
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
Product
UX Range Broadband Power Amplifiers 2 GHZ - 6 GHZ
UX Series
-
Class A solid stateBroadband (instantaneous single band): 2 GHz 6 GHzTypical output power : 15 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 12 W and H < -20 dBc up to 4 GHz andP1dB > 11 W and H < -20 dBc from 4 GHz to 6 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to UX 30 possible (4U)Reliable, efficient and robust19" Rack3 years standard warranty
-
Product
4-Channel 200 MHz A/D with DDC, Virtex-6 FPGA - 6U VPX
Model 57661
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- One multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Amplifier-in-Cable Small Proximity Sensor
EM Series
-
Amplifier-in-Cable Small Proximity Sensor. Ultra-small sensor head. Amplifier and operation indicator built into cable. Strong, flexible cable IP-67 waterproof housing
-
Product
1 GHz A/D and D/A with Virtex-6 FPGA - 6U VPX
Model 57630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
6-Channel VME Pulse Amplifier
V860
-
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
Product
Adaptive Relay, Virtex-6 FPGA - 3U VPX
Model 52624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
SMT & QFN Products
-
PMI offers custom surface mount (SMT) and QFN packaging for many types of devices. SDLVA's, Log Amplifiers, Phase Shifters, Attenuators, Switches, as well as Low Noise Amplifiers. PMI also offers multifunction options in a single QFN package such as Limiter / LNA or LNA / Detector. PMI has the experience to offer custom devices that meet your specific control function at high frequency. Mounting and integrating high frequency RF devices take skill and experience such that the package itself does not degrade the RF signal. PMI has the experience in selecting the proper package, integrating the RF devices and providing the required testing.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
4-Channel 200 MHz A/D with 1532 DDCs, Kintex UltraScale FPGA - 6U VPX
Model 58865
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete software radio receiver solution for extremely high channel-count applications- Uses Xilinx Kintex UltraScale KU035 FPGAs- Four 200 MHz 16-bit A/Ds- Eight wideband DDCs (digital downconverters)- Up to 1524 narrowband DDCs- Sample clock generation and synchronization to an external system reference- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Bi-Directional Amplifiers
-
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
Product
Isolation Amplifier
-
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
Booster and In-line Amplifier
-
Amonics' EDFA range adopts unique design to produce maximum signal gain and saturated output power while maintaining low noise figure, enabling test capabilities in system or component level manufacturing and characterizing processes, as well as facilitating highly demanding R&D applications. The compact turnkey benchtop or 19" rackmount unit incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power control knob and optical connectors. An integrated RS232 computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 6U VPX
Model 58751
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two or four 500 MHz 12-bit A/Ds- Two or four multiband DDCs (digital downconverters)- One or two DUCs (digital upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
