Product

Magnet Wheels Pulse Generators

199SM / 198EM Magnet Wheels

-

Electro-Sensors, Inc.

199SM / 198EM Magnet Wheels - Electro-Sensors, Inc.

Magnet wheels work with Electro-Sensors Hall Effect shaft speed sensors providing 120 alternating magnetic poles around the circumference of the 3.75" diameter. The 199SM models mount around shafts up to 3" in diameter and are secured with set screws (provided). The 198EM mounts on the end of a shaft with a 10-32 UNF screw (provided - requires center drilling and tapping the shaft).• Use with 906, 906B, 1101 and other Hall Effect, non-metallic-end-capped shaft speed sensors (consult factory)

Product

50MHz Single-Channel Pulse Waveform Generator

PM8571A

-

Tabor Electronics Ltd.

PM8571A - Tabor Electronics Ltd.

Model PM8571A is very high performance, single channel pulse/pattern generator that stretch normal pulse generators` spec to the limit, becoming by far the most advanced pulse waveform generator available in the market. In addition to its high performance pulse features, the new PM8571A generate a complete array of standard, arbitrary and sequenced waveforms which are necessities in today`s laboratories.

Product

Voltage Pulse Generator

SKS-IV10J

-

Shanghai Sanki Electronic Industries Co., Ltd.

SKS-IV10J - Shanghai Sanki Electronic Industries Co., Ltd.

The voltage pulse generator SKS-IV10J is completely designed in accordance with the requirements of the impulse voltage chapter in OIML R 46-1/-2; it meets the requirements of the new IEC60255-5 and GB14711 standards; the leakage current detection alarm function is added, and the leakage current limit can be Adjustment; using linearized high-voltage power supply, low noise, high stability, high voltage accuracy and long service life.

Product

Pulse Generator

Traction Wheel Assembly

-

Electro-Sensors, Inc.

Traction Wheel Assembly - Electro-Sensors, Inc.

The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies. • Square-wave frequency output, NPN open-collector • 5-28 VDC powered • 1 to 1,270 pulses per revolution (PPR - specify when ordering) • Optional bi-directional (quadrature) output models • 3 models: black neoprene rubber, smooth polyurethane, and diamond knurled aluminum tread

Product

High Voltage Pulse Attenuators

-

Barth Electronics, Inc

Barth Electronics, Inc

Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor.  These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators.  These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.

Product

High Voltage 50 Ω Pulse Generator

TLP-8010C

-

High Power Pulse Instruments GmbH

TLP-8010C - High Power Pulse Instruments GmbH

*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components