ESD Simulators
create known values of electrostatic discharge.
See Also: ESD Test, ESD Test Systems, ESD Generators
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
LXI Simulation Tool
60-901-001
-
This tool will simulate all of our PXI & LXI switching products and most of our PXI simulation products allowing for code development independent from your application hardware
-
Product
ESD Testing & Latch-Up Testing Services
-
EAG is an industry leader in ESD testing (Electrostatic Discharge) and Latch up testing. Our highly experienced engineering team use their industry leading knowledge and years or real world experience of the latest semiconductor technologies, circuit design, and device physics to optimize our customer's ESD and latch-up results. Human Body Model (HBM) and Machine Model (MM), Charged Device Model (CDM), Latch-up, Transmission Line Pulse (TLP).
-
Product
Power System Simulator
F6150e
-
This power system simulator performs the simplest through the most complex tests. Meeting all your protective relay testing needs, the F6150e is available in different configurations.
-
Product
Capacitance Simulation Card
SET-1220
-
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
Transducer Simulator
Model 7V
-
Impedance: 350 ohms nominal. Output Ranges:Fixed rotary switch: 0 to 3 mv/v in 6 steps of .5 mv/v .
-
Product
Surge/wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Surge pulses occur due to direct or indirect lighting strokes to an external circuit. This leads to current or electromagnetic fields causing high voltage or current transients. Another source for surge pulsed is switching transients originating from switching disturbances and system faults.
-
Product
GNSS Testing & Simulation
-
Safran Federal Systems is a leading provider of advanced GNSS Testing & Simulation systems and tools for NAVWAR environments.
-
Product
ESD & Latch-Up Test Service
-
MASER Engineering has automatic test equipment for the most common ESD test pulse models. MIL - JEDEC - ESDA - IEC standards. IC level Human Body Model. IC level Machine Model. IC level Charged Device Model. System level IEC 61000 HBM. AEC-Q100 Field Induced Gate Leakage test. Static Latch-Up test. Dynamic Latch-Up test.
-
Product
Circuit Simulation Software
SIMetrix/SIMPLIS
-
SIMetrix/SIMPLIS is an advanced simulation tool optimized for efficient design of power electronics circuits. SIMetrix/SIMPLIS combines accuracy and convergence in a unique and powerful design environment, enabling 10-50x faster simulation for power supply designs. SIMetrix is a mixed-mode circuit simulation package designed for professional electronics engineers. SIMetrix comprises a substantially enhanced SPICE simulator, schematic editor and waveform viewer in a unified environment.
-
Product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
-
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
Product
Accelerometer Simulator
MTN/8302
-
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
Product
MIMIC sFlow Simulator
-
MIMIC sFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
Product
Target simulators
-
Simat simulator is an advanced hardware simulator capable to simulate in infrared range several targets on quasi uniform background. In detail Simat simulator is a modular image projector capable to simulate in infrared range variable intensity, variable angular size, variable spectrum, spatially and temporally dynamic airborne type targets on quasi uniform background. Basically the aim of Simat to enable simulation typical airborne targets like aircrafts or helicopters for infrared imaging sensors used for surveillance of these targets. Optionally Simat can be modernized to enable simulation in both IR and UV/visible ranges as the projectors are built using broadband reflective optical elements.
-
Product
NIBP Simulator
SC-3 SimCube®
-
This NIBP only simulator provides features to perform basic NIBP testing of a patient monitor. Features one-button operation for quick testing of patient monitors and optional Battery Boost Option. Optional accessories provide all you need to test the NIBP parameter on any type of patient monitor.
-
Product
OBD2/J1708/J1587 Simulator
DFLSOBD2
-
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
Product
IMU MODELING AND SIMULATION
-
CAST Navigation’s INS systems provide high rate inertial data with exceptional fidelity to support the integration and testing of today’s complex EGI and GNSS/INS navigation systems. The CAST system is designed for optimal performance when the inertial sensor and GNSS receiver are either loosely, tightly or ultra-tightly coupled, or when an INS aiding source can be utilized by any other type of device.
-
Product
The Imperas Instruction Set Simulator
ISS
-
The Imperas ISS is often the first simulation product used in an embedded software development project. The Imperas ISS allows the development and debug of code for the target architecture on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running the ISS with an argument to specify the name of the application object.
-
Product
Avionics Test & Simulation Interfaces
Interface
Connect your PC laptop, desktop and tablet computers to avionics databuses with pocket-sized Ballard USB interfaces. Ease of use, versatility and comprehensive databus functionality have made these rugged adapters the industry favorite for avionics test, analysis and simulation in the lab and in the field. Avionics labs routinely integrate Ballard interface cards and full-featured network appliances into their test setups for powerful and reliable databus connection.
-
Product
Photovoltaic Array Simulation Solution
-
The Keysight N8937APV and N8957APV photovoltaic array simulators are capable of testing PV inverters up to 1,500 V, enabling designers to participate in the recent industry shift to the higher voltage. They can quickly simulate I-V curve characteristics under different environmental conditions (temperature, irradiance, age, cell technology and more), enabling the user to quickly and comprehensively test their solar inverters.
-
Product
Sunlite Solar Simulators
-
- Gen III Optics for High Efficiency Illuminati- Infinitely Adjustable Irradiance, Reproducibly Settable- Class A AM1.5G Spectral Match- ASTM Class A stability- 50×50 mm Class B uniformity- Manual Shutter Included, Electronic - Shutter Optional- Uninterrupted testing with the prealigned lamps- HEPA filtered air cooling
-
Product
Wafer ESD Tester lineup
-
Hanwa Electronic Ind. Co.,Ltd.
◆Correspond to 300mm Wafer. This tester can measure LED or the large sizes Wafer, such as a system LSI. And Zap of HBM/MM can be performed. The Automatic destructive judging by V/I measurement can also be performed after Zap.◆Waveform guarantee in Zap needles. HED-W5100D carries out the calibration before shipment in the place of Zap needles. Therefore, Correlation of the Result of a Package Device becomes clear easily.◆Correspondence to Standards This Tester corresponds to the Standard of JEITA, ESDA, and JEDEC. A Zap unit adopts the plug-in system and also has the waveform of Customer's requests.◆Connection with TLP This Tester is the best for TLP Testing with deep relation of ESD. The protection circuit of a device with an ESD problem is investigated.
-
Product
Radar Simulation Software
Pulse Sequencer
-
R&S®Pulse Sequencer software together with a vector signal generator from Rohde & Schwarz or just as software provides a compelling radar signal generation solution to engineers and technicians responsible for testing radar receivers. The solution is in line with the trend of testing more in the lab rather than expensive field testing. Co-engineered with the industry, the solution supports all relevant modern radar scenario test cases and can account for real-world environments. It uses commercially available R&S®Pulse Sequencer PC software and off-the-shelf Rohde & Schwarz vector signal generators.
-
Product
Simulating Optical Design Components
Wave Optics Module
-
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
Product
Hot Socket Simulator
Hot Socket Simulator
-
The new TESCO Hot Socket Simulator gives you the ability to investigate meter failure issues related to hot socket phenomenon. The Simulator is equipped with one 2S meter socket with four jaws, one of which is the heated jaw. The arcing/heating apparatus can be moved to any of the four jaws (jaw 1 is the standard). Additional arcing/heating elements can be provided as an option for multiple hot jaws on the existing socket.
-
Product
Simulation And Training
-
With more than 25 years of experience, Textron Systems Simulation and Training provides comprehensive end-to-end training solutions for air, land, sea, space, unmanned and electronic warfare platforms. We design, develop, and support integrated training devices, classroom courseware, virtual, live and constructive training, and software solutions. Our products and services support advanced platforms including C-17 Globemaster®, B-1 Lancer, F-35 Lightning II®, F-22 Raptor® and other high-value assets. Textron Systems also produces electronic, RF, and/or multispectral test equipment for verification and validation of these and various other air, land, sea, space, unmanned and electronic warfare platforms.
-
Product
Multifunctional Simulators
CCS600
-
Suzhou 3ctest Electronic Co.,Ltd.
CCS600 designed as a modular system is the most intelligent solution offering exactly what people need for full-compliant immunity tests against transient, surge and voltage dips. The max voltage is up to 6kV.
-
Product
SIMulation Workbench
-
A comprehensive framework for developing and executing real-time hardware-in-the-loop and man-in-the-loop simulations.
-
Product
LED solar simulators
-
We offer innovative A + A + A + LED solar simulators for the integration of the production process and for the stand-alone operation in the laboratory or goods receipt. Our LED solar simulators are characterized by maximum repeatability, a long pulse duration and very low maintenance.
