ESD Simulators
create known values of electrostatic discharge.
See Also: ESD Test, ESD Test Systems, ESD Generators
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
IBP Simulator
IBPS 2.0
-
The IBPS 2.0 is a PC controlled simulator to replace real IBP sensors. Originally designed for IEC 60601-2-34 testing, it can also be used by manufacturers to play their own test signals or database recordings.
-
Product
Camera Simulators
CoaXPress
-
Ideally suited for industrial, defense and aerospace Machine Vision Systems and applications, as well as for development and manufacturing purposes.
-
Product
Surge/wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Surge pulses occur due to direct or indirect lighting strokes to an external circuit. This leads to current or electromagnetic fields causing high voltage or current transients. Another source for surge pulsed is switching transients originating from switching disturbances and system faults.
-
Product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
-
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
Product
PXI Analog Output/Current Loop Simulator Module - 16 Channel
41-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Modbus Simulator
Modbus Slave
-
Modbus Slave is for simulating up to 32 slave devices in 32 windows!. Speed up your PLC programming with this simulating tools. Start programming and test before you receive your slave device from supplier.
-
Product
Cost-Effective Network Simulator
Emutel Maestro
-
Emutel Maestro brings you the perfect solution for testing your DSL equipment. Connect to your product while still in your own testing lab and perform those final tests in a real environment, enabling you to identify and solve any problems before they occur on site.
-
Product
2 PRI + 8 Port FXS PSTN Simulator Adv
CH-8FXS-MOD-2PRI-A
-
One of the most feature rich PSTN simulator on the market. Unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
VectorPro - Simulation Cyclizer for VCD to WGL/STIL
VectorPro
-
VectorPro is a low-cost, intuitive test development tool used to translate VCD/EVCD simulations into cyclized ATE Test Vectors in either WGL or STIL formats. This highly versatile tool reads in both VCD and EVCD formatted design simulations, and through the use of its flexible GUI, users are able to view and modify the simulation to fit the needs of their Test Environment.
-
Product
Voltage Dip, Interruption& Variation Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
Product
Field Simulation Software
QuickField™
-
QuickField™ is a very efficient Finite Element Analysis package for electromagnetic, thermal, and stress design simulation with coupled multi-field analysis.
-
Product
Power Supply Voltage Fluctuation Simulator
SG Series
-
Simulator to reproduce DC supply voltage variations phenomena in the vehicle environment for evaluating immunity of automotive electronics. This simulator can perform various tests against voltage variations required by ISO 16750 and other international standards. Please contact us for voltage variations testers to perform testing to manufacturers' private standards.
-
Product
ECU Simulator
PT-LabCar
-
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
Product
Lightning Impulse Simulation Tester
KT-6030iG
-
Most of all electric systems and equipments are weak against the lightings(direct, inductive lightning). In fact, those electric equipments are broken mainly by lightning.This Lightning Impulse Simulation Tester is certificated to IEC 61000-4-5, and generates the similar impulse with huge rush currents and tests the safety of the power systems and equipments.
-
Product
Ohm-Stat Ground/Circuit Tester to Test ESD Ground
-
Tests ground for all 110v electrical circuitsWill determine the status of all electrical groundsEasy to use LED lightsWarranteeProduct conforms to the ESD S.20.20 spec standardsIdentify electrical problemsUsed with the Ohm-Stat RT-1000 resistivity meter
-
Product
GNSS Modeling And Simulation
-
CAST Navigation’s GNSS simulation systems produce GNSS RF signals that provide a precise and repeatable testing signal, perfect for use either in the field or in the laboratory environment. These systems can be used for a wide range of testing and integration verification applications and they are an ideal choice for stimulating military or commercial devices where only GNSS signals are needed. Our simulators are powered by proprietary multi-frequency, multi-constellation GNSS RF signal generation technology. This technology provides you with highly accurate and fully programmable signals along with advanced vehicle trajectory capabilities allowing you to custom tailor parameters and trajectories to meet your simulation requirements.
-
Product
Electronic Warfare MMI and HMI Simulators
MS 1600
-
The EW IFU (Electronic Warfare Interface Unit) interfaces between Cockpit electronics viz., RWR Display Unit (DU), New control Box (NCB), CMDS Control/Display units and Simulator Host Computer (HOST). The EW IFU transmits the status of the cockpit control units to the host, receives display data from the host and transfers the same to RWR DU, NCB and CMDS CCU/CDU. The display data for the RWR DU received from the host would comprise of the complete symbol data in respect of emitters that are to be displayed based on the data from the Instructor Station (IS) and control input from the cockpit. The display unit receives and presents the data as symbology on the display screen. The EW IFU based on the PC–AT.
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
T400 Radar Emulation Simulator
-
Kratos Defense & Security Solutions, Inc.
The Radar Emulation Simulator provides a cost-effective solution for simulating targets and channel effects in an RF environment. The system can be controlled via a standalone graphical user interface for simplified scenario applications, a dedicated real-time interface, or remotely via the Ethernet interface.
-
-
Product
MIMIC SNMP Simulator
-
MIMIC SNMP Simulator creates a network of up to 100,000 SNMP manageable devices on one server. You can simulate any SNMP based device with any number of public or private MIBs to run a large variety of device configurations with your SNMP management application. It lets you generate thousands of traps to simulate disaster scenarios.
-
Product
2 PRI + 32 BRI-U ISDN Simulator
CH-32BRI-U-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
Stand-Alone Automated ESD Scanner
SmartScan 550
-
API's main hardware platform that most scan technologies can be integrated to this platform. 550 represents the four-axis robot arm size. It is a stand-alone model.:
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
Simulator
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
PXI Analog Output / Current Loop Simulators
-
These modules are aimed at simulating industrial control transceivers, utilizing 4–20mA current loops. The modules include built-in relays for shorts and opens functionality enabling fault insertion testing on every channel and also enable slew rates to be programmed so that different sensors can be effectively mimicked.
-
Product
Regenerative Grid Simulator
61800
-
Chroma Systems Solutions, Inc.
Power rating: Up to 300kVA, single or three phase outputOutput Voltage: 0~330V L-N / 0~570V L-L0~400V L-N / 0~692V L-L opt. without using a transformerOutput Frequency: DC, 30Hz~100HzMaximum power delivered down to 200VAC L-NFull 4 quadrant, fully regenerative up to 100% of output current ratingSpecifically designed for PV inverter, Smart Grid and EV related test applicationsProgrammable slew rate settings for voltage and frequencyProgrammable voltage and current limitsTurn on, turn off phase angle controlLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetParallel output for higher power applications (three phase only)
-
Product
Basic Rate and Primary Rate Simulator
emutel Pro
-
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
Product
EM & Thermal Simulation Software
SEMCAD X
-
Schmid & Partner Engineering AG
SEMCAD X is the latest generation of 3-D FDTD full-wave simulation software offering unprecedented levels of user-friendliness, speed & memory efficiency. Its application range has been further greatly extended by incorporating the world's first EM ADI-FDTD solver.
