-
Product
Solar Cell Tester
REOO RO-GTM2615
-
REOO RO-GTM2615 Solar Cell Tester is designed for PV cell manufacturing inspection, enabling fast cell performance inspection and stable electrical quality verification. Built for solar factories, it improves cell testing accuracy and maintains stable operation across PV cell production lines.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Benchmark, Competitive and Failure Analysis
-
Helping you determine the root cause of product failures and evaluate products against industry competition and standards.We provide third-party verification and support for claims related to performance versus competition, root product failure cause, and benchmark industry performance. As an independent laboratory with over 60 years of product testing experience, our expertise helps you evaluate products for a variety of performance related characteristics. Additionally, we can provide expert witness legal testimony for insurance claims, CPSC filings, and civil/criminal court cases through our testing results and data.
-
Product
Solar Analyzers
-
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
Product
Assembly and Testing of Power Steering Motors
-
Interlinked stations for assembly and testing of servo-electric steering drives*Station 1: Force / path monitored*Station 2: Verification of the software version, with variant-dependent parameterization*Station 3: Leak test as vacuum test as the overpressure test*Station 4: Function and noise testing and order analysis
-
Product
AS5653 Protocol Compliance Testing Solution
AS5653-PTP
-
Avionics Interface Technologies
Production Test Plan for SAE AS5653 - Full Suite of Verification tests to verify NC and NT operations in accordance with AS5653 - Utilizes AIT HS1760 Hardware - Automated Execution and Reports of Results - Python Test scripts - General exchange, sequence, and frame validation at the completion of each test - Production Test Plan for AS5653 Switch Compliance is also available
-
Product
EasyQRCode
-
Automatic detection of the code in the imageDecodes model 1 and model 2 QR codes, all versions, all levelsDecodes Micro QR codesVery fast operationImpressive robustness to noise, blur and distortionError detection and correctionRotation and flipping invariantPrint quality verification with grading standardsMultiple codes reading
-
Product
Automotive Ethernet Tx Test Software 10M To 10Gbp
AE6920T
-
Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The automotive Ethernet test solution AE6900T offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.
-
Product
JTAG (and IJTAG) Environment Tool Suite
SAJE
-
SAJE is the SiliconAid Suite of JTAG related standards focused tools for chip development, verification, validation and patterns generation of ATE, Board, and System Test. Each tool can be used as a point tool by itself to compliment other tools in your flow. However, the SAJE Tool Suite used together in a flow can provide a total solution that also leveraging previous steps for debug and analysis.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm - SPST
40-294-111
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Embedded Engineering Solutions
-
Our engineering solutions support the development of safety-critical embedded systems. We support systems, hardware and software engineering, software V&V including multicore timing analysis, the development of efficient automated test environments, and develop custom tools to meet verification needs.
-
Product
Handheld Raman Spectrometer
NanoRam® – BWT-840000341
-
The NanoRam is a state-of-the-art handheld Raman instrument for nondestructive identification and verification of materials such as APIs, excipients, intermediates, & finished products. Compact and agile, the NanoRam can be used by non-technical users to rapidly identify samples in the lab, warehouse, loading dock or field, helping to eliminate quarantine areas and expedite materials through the manufacturing lifecycle. Utilizing Raman technology, non-contact analysis can be performed through transparent containers, all while maintaining the volume and integrity of the sample.
-
Product
Services, testing
-
They are particularly the voltage tests, power, mechanical and electrical durability tests as well any verification of the LV and MV switchgears including the type tests.
-
Product
Engineering Design & Development
-
TPSA has over 20 years of experience in Engineering Design & Software Development including:Hardware & Software DesignOTPS Acquisition SupportSystems Installation & SupportAircraft Modification/CertificationEngineering Studies & AnalysesFunctional & Systems TestingIndependent Verification & Validation (IV & V)Test Program Set EngineeringReliability & Maintainability (R&M)Engineering Drawings & DataConfiguration Data ManagementReverse EngineeringRequirements AnalysisSupport Equipment (SE)Aircraft Launch & Recovery Engineering (ALRE)Engineering Change Proposal (ECP) ReviewTechnology Insertion (TI)PDR, CDR, FAT, Techeval, OSV Support
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Hybrid Wound Component EST Scanner
19035
-
Chroma Systems Solutions, Inc.
The quality verification test items for Wound Components consist of AC/DC Hipot tests and Insulation Resistance (IR) tests. Chroma integrates the above tests into the Hybrid 19035 Wound Component EST Scanner series to perform safety tests for motor, transformer, and heater related wound products. The wound component manufacturers performing quality verification testing will not only have reliable quality, but also can control product quality efficiently.
-
Product
Mode-Conditioned Light Sources
-
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
Product
Automated And Connected Mobility Testing
-
The future of mobility will be highly automated. Most new vehicles already feature some sort of assistance systems and rapidly advance into more complex functionalities. But with such technological progress comes increased development effort, complexity, and time-to-market pressures. We offer a great variety of solutions for the calibration, verification, and validation of Advanced Driver Assistance System (ADAS) and Autonomous Driving (AD) features to ensure robustness, reliability, performance quality, safety, and user acceptance.
-
Product
Functional Testing For Critical Software
RapiTest
-
*Requirements-based testing for Ada, C & C++ on-host & target*Reduce test authoring effort through easy-to-use test formats*Manage project artifacts with requirements traceability*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
Product
Universal Programmer Superpro 7500
-
Until now,Support 396 IC manufacturer, 94596 pcs devices and keeps growing.Support devices with Vcc from 1.2V to 5V. The programming speed up further increase 30% compared to SUPERPRO 5000.The programmer support files up to 256 GBytesBuilt with 144 universal pin-drivers.Universal adaptors are available for varies packages up to 144 pins. New device support will be easier. PC hosted mode and stand-alone mode. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. Under stand-alone mode the programmer is controlled via the 6-KEY keypad and the 20 character by 4 line LCD display. A SD card is used to store the project files.User can operate multiple units to construct a concurrent multiprogramming system thank for the stand-alone mode. Only IC manufacturer approved programming algorithms are used for high reliability. (+5%~-5%) and (10%~-10%) Vcc verification enhances programming reliability.Advanced and powerful functions.Production mode start chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Serial numbers generators are available as standard or customer-specific functions.Log file is useful for quality tracking. Over-current and over-voltage protection for safety of the chip and programmer hardware. WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm - SPST
40-294-113
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
100 High Speed Programmer
Commander Accelerator
-
The Commander High Speed Programmer (HSP) is low overhead system designed to test Flash Memories, PLA's and Micro-controllers. The parallel multi-module architecture provides the flexibility to program and test multiple devices. It's full-featured capabilities support chip erasing and programming, sector erasing and programming, sector protect and unprotect, and data verification functions.
-
Product
Short Pulse High-Frequency Laser Marker
LP-RV SERIES
-
Panasonic Industrial Devices Sales Company of America
The LP-RV Series FAYb Laser Marker features:- Short Pulse 20W Fiber Laser Offers Excellent Mark Contrast On Difficult To Mark Plastics And Various Other Materials- Optional EtherNET/IP Or ProfiNET Interface Adaptor Card- Modular Laser Oscillator System Makes Servicing In The Field Possible - Direct Connection To Panasonic PV230 Vision System For Mark Verification, Auto-Targeting, And Other Machine Vision Functions- Compact IP64-Rated Marking Head For Use In Harsh Environments- Compliant With FDA Regulations, GB Standard, KC Mark, Machinery Directive (Declaration of Incorporation), EMC Directive, RoHS Directive
-
Product
System for the Analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel
SierraNet T328
-
The SierraNet T328 system provides for analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel data capture and protocol verification for developers & protocol test engineers in LAN, SAN, NAS and other Ethernet and Fibre Channel applications. Available with eight SFP28 FlexPorts™ for maximum configuration and utility, the SierraNet T328 includes an easy to use, customizable software interface, large capture buffers, and the most advanced T.A.P4 capture, triggering and filtering capabilities in the industry.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm
50-293-021
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 4-Channel 1R to 127R with SPDT
40-293-112
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Test Equipment
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Test Equipment, including handheld electrostatic fieldmeter, periodic verification system, charged plate monitor, contact voltmeter, and others.
-
Product
Framework for Soft-Error Protection
RobustScan™
-
RobustScan™ provides a platform for users to pick patented Configurable Soft-Error Resilience (CSER) cells or their preferred SER mitigation cells. First, Soft-Error Rate (SER) analysis is performed. Then it performs automatic robust-scan-cell and hardenedcombinational- cell selection and synthesis. Finally it generates verification testbenches for the final design. RobustScan™ can be used with scan chains inserted using third-party tools; it can be linked to third-party�s SER analysis programs and is fully compatible with SynTest�s existing DFT tools for test, debug, and diagnosis.
-
Product
Process Monitoring, DAQ & Software
sigPOD
-
sigPOD is Sciemetric’s out-of-the-box solution for monitoring test and assembly processes that standardizes part test and process monitoring onto a single platform for manufacturers. With sigPOD, process signature verification can be deployed across the production line on virtually any manufacturing process. Gain the data-driven insight you need to compete in an Industry 4.0 world.
