Pickering Interfaces Inc.
Pickering Interfaces designs and manufactures modular signal switching and simulation for use in electronic test and verification.
- 781 897 1710
- ussales@pickeringtest.com
- 170 Main Street
Unit 108
Tewksbury, Massachusetts 01876
United States of America
Categories
-
product
PXI 5A Power Multiplexer, 2-Bank, 24-Channel, Isolated Common
40-651A-012
The 40-651A-012 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
product
PXI 8-slot BRIC Multiplexer, 3-Channel, 160-Pole (5 Sub-cards)
40-570A-013
The 40-570A-013 is a 3-channel, 160-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
20-Pin GMCT Cable, Male to Female, 10A, 2m
A020GMR-020GFR-0B200
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-D/10/8
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm
40-294-023
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Single 48-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-001
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
product
Cable Assembly 44-Pin D-Type Male to Female, 0.5m
40-970-044-0.5m-MF
The 44-Pin D-Type Density and a Half cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
PXI 8-Slot BRIC Matrix, 55x16 2-Pole (5 sub-cards)
40-562B-122-55X16
The 40-562B-122-55X16 is a high density BRIC8 matrix module with a size of 55x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
200 Pin LFH Cables - 200 Pin to Unterminated
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin LFH connector.
-
product
High Voltage 9-Pin D-Type Connector & Cable Accessories
The High Voltage 9-Pin D-Type connector is used on high voltage PXI and LXI switching products to provide a high voltageconnector solution. Connection solutions for modules with Standard Voltage Rating D-Type connectors are also available.
-
product
200-Pin LFH Connector, Male, M3 Male Screwlocks
40-961A-200-M3-M
This connector is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector.
-
product
SIMRC Card Carrier
1050-001
The SIM Relay Carrier 1050 simplifies the custom integration of small format embedded switching cards. No additional PCB design is necessary. Due to the Eurocard format the carrier can be fitted into a standard case or can be mounted in a 19" rack with side rails. Plug in standard SIM Relay Cards and control your switch application with the provided Soft Front Panel without any additional programming.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
LXI Reed Relay Matrix - Single 128x4 Plugin, No Direct Y Access, 12 Analog Buses
65-221-102
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
40-876A-002
The 40-876A-002 (PXI) and 42-876A-002 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
